Suptek ML6802 User manual

ML6802
n1
h
o
o
INSTALLATION MANUAL
UNPACKING INSTRUCTIONS
Carefully open the carton, remove contents and lay out on cardboard or other protective
surface to avoid damage.
Check package contents against the Supplied Parts List in the next page to assure that
all components wete received undamaged. Do not use damaged or defective parts.
Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
Install and operate this device with care. Please read this instruction before installation,
and carefully follow all instructions contained herein. Use proper safety equipment during
installation.
Please call a qualified installation contractor for help if you
directions or have any doubts about the safety of the installation.
Do not use this product for any purpose or in any configuration not explicitly specified in
this instruction. We hereby disclaims any and all liability for injury or damage arising from
incorrect assembly, incorrect mounting, or incorrect use of this product.
Make the Necessary Adjustments
Step 5
Adjust and tighten the bolt with the
supplied Allen Key（O）to fix the tilt angle
By adjusting the tightness of the
screws, the height of the monitor
can be adjusted.
Step 6 Manage the Wires and Store the Allen Keys on Wire Clip
The wire is held in place with a cable clip (n1)
Attach the VESA Plate to the Monitor
Step 3
qs or g
r
For Monitor with Flat Back For Monitor with Curved or
Recessed Back
Step 4 Install the monitor to the pole
Secure and lock the panel with nut(h)
Insert the monitor into the head
attachment of the rotating arm
Thank you for choosing our products!

(2) Pole -a (2) Head sleeve -d (2) VESA Plate-e
(3) M5X16 Bolt -f (8) M8 Spacer -g (2) Nut -h
(2) Wire Clip -n1 (1) Allen Key -o
(1) M10 Bolt -i (1) Support Plate -j
(1) M10 Washer-k (1) Spring Washer -l
(1) Wrench -p (8) M4X12 Bolt -q (8) M4X30 Bolt -r (8) M8 Spacer-s
(3) M5X16 Bolt -b
a
j
l
k
i
b
o
d
Step 1 Install the Pole to the Desktop
Option B: Grommer Base Install
Self Drilled Grommet Hole Installation
1. Position the Pole(a) on the mounting
surface and amark the center hole. Drill a 3/8”
(10mm) diameter hole at the marked position
through the mounting surface.
2. Install the Grommet Base Plate(m) to the
Pole(a) using 3pcs M5x16 Bolts(f), and
tighten using the Allen Key(o), see Fihure 5.
3. Position the Pole(a) on the mounting
surface and secure using the Support Plate
(j). M10 Washer(k), Spring Washer(l) and
M10 Bolt(i), Fasten the M10 Bolt using
provided Wrench(p), see Figure 6.
a
m
fFigure 5
Figure 6
j
k
l
i
Install the head sleeve to Pole
Step 2
Place the head sleeve(d) over the pole,
and tighten with Allen Key（o）
Step 1 Install the Pole to the Desktop
u2
t
u1
upper base：
Remove the screw with a wrench to separate
the upper base(u2) and bottom base(u1)
Align bottom of Supporting Legs(t) with
bottom base(u1), face of them with upper
base(u2), then tighten them with screws.
Option A: Desk Clamp Install
Figure 1
1. Install the Pole(a) to the Weighted
Base(b), using 3 pcs M5X12 Bolts(e) ,
see Figure 1.
2. Optionally, you can drill a 10mm
diameter hole in your desk and secure
using the Support Plate(j), M10 Washer
(k), Spring Washer(l) and M10 Bolt
(i), Fasten the M10 Bolt by provided
Wrench(p), see Figure 2.
Figure 2
a
m
f
j
k
i
l
Option B: Grommet Base Install
Existing Grommet Hole Installation
If the existing grommet hole comes with a
plastic protector, remove it to ensure a flat
surface before installing the desk mount.
1. Install the Grommet Base Plate(m) to the
Pole(a) using 3 pcs M5x16 Bolts(f) , and
tighten using the Allen Key(o), see Fihure 3.
2. Position the Pole(a) on the mounting
surface and secure using the Suport Plate
(j), M10 Washer(k), Spring Washer(I), and
M10 Bolt(i). Fasten the M10 Bolt using
provided Wrench(p), see Fihure 4.
Figure 3
Figure 4
WARNING
CAUTION!
This monitor desktop mount must be securely
attached to the horizontal desk. If the mount is
not properly installed it may fall, resulting in
possible injury and/or damage.
Tools Required Phillips Screwdriver
Supplied Parts List
(1) Grommet Base
Plate-m
(2) Supporting leg-t (1) bottom base-u1 (1) upper base-u2
Tighten and splice two poles into one,
then tighten the stud with wrench to secure