Premier Mounts LPSA3747 User manual

INSTALLATION INSTRUCTIONS
LPSA3747
Universal Low Profile Swingout Arm for 37” to 47” Flat Panels
NORTH AMERICA
3130 East Miraloma Avenue
Anaheim, CA 92806 USA
USA and Canada –
Phone: [phone]
Fax: [phone]
EUROPE
Swallow House,
Shilton Industrial Estate,
Shilton, Coventry, England CV79JY
Phone: [phone]
Fax: [phone]
Other Locations – Phone: [phone]; Fax: [phone]
©Premier Mounts 2009
9531-211-001-04

Page 2 Installation Instructions
Table of Contents
Warning Statements
Warning Statements 2
Parts List 3
Installation Tools 3
Wood Stud Installation 5
Concrete Surface Installation 6
Determining the Mounting Hardware 8
Universal Spacer Installation 8
Attaching the Flat Panel (75mm/100mm Mounting Points) 9
LPSA3747 Installation 10
Tilt/Pivot Adjustment 10
Assembling the Adapter Plate 11
Universal Washer Installation 12
Attaching the Adapter Plate to the Flat Panel 12
Attaching the Flat Panel with the Adapter Plate 13
LPSA3747 Installation with the Adapter Plate 14
Tension Adjustment 15
Cable Management 15
Technical Specifications 16
Warranty 17
LPSA3747
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND
COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND
PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE
REFERENCE.
PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS
PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED
ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS,
ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER
RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.
THE SURFACE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE FLAT PANEL. IF NOT, THE
STRUCTURE MUST BE REINFORCED. THE MAXIMUM WEIGHT THAT CAN BE USED WITH THIS PRODUCT IS 80LBS. PROPER
INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUC-
TIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN DEATH.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER SAFETY
GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.
At least two qualified people should perform the assembly procedure. Injury and/or damage can result from dropping or mishandling the flat
panel.
If mounting to studs, make sure that the mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud finder is
recommended.
Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical
wires in wall. Cutting/drilling into an electrical line may cause serious injury.
Make sure there are no water lines inside the wall where the mount is to be located. Cutting/drilling into a water line may cause severe water
damage to the mounting surface.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact
Contact Premier Mounts with any questions
[phone]
[email protected]

Installation Instructions Page 3
Parts List
Installation Tools (not supplied)
Cover Plate (Qty 1)
Universal Adapter Plate Hardware
Adapter Arms (Qty 2)
Adapter Plate (Qty 1)
Plastic Wall Anchors
(Qty 4)
#14 x 2” Wood Screws (Qty 4)
4” Cable Ties (Qty 2)
Universal
Spacers (Qty 30)
Pencil
5/32” Allen
Wrench (Supplied)
M3 Allen
Wrench (Supplied)
Thread Depth
Indicator (Supplied)
Level
1/8” Drill Bit
(pilot holes)
Electronic Studfinder Socket Wrench
Phillips Tip
Screwdriver
Tape Measure
Hand Held Drill
Wall Plate (Qty 1)
Hammer
LPSA3747
M6 Set Screw (Qty 4)
LPSA3747 Hardware
Congratulations on the purchase of your new Premier Mounts LPSA3747 flat panel mount. This
mount is shipped with all proper installation hardware and components. Make sure that none of these parts are
missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the
installation and contact Premier Mounts [phone].
14mm Socket
Universal Washers (Qty 6)

Page 4 Installation Instructions
LPSA3747
M4 x 8mm (Qty 4)
M4 x 10mm (Qty 6)
M4 x 16mm (Qty 6)
M4 x 25mm (Qty 6)
M4 x 30mm (Qty 6)
M6 x 30mm (Qty 6)
M6 x 25mm (Qty 6)
M6 x 16mm (Qty 6)
M5 x 30mm (Qty 6)
M5 x 25mm (Qty 6)
M5 x 16mm (Qty 6)
M8 x 30mm (Qty 6)
M8 x 25mm (Qty 6)
M8 x 16mm (Qty 6)
If your unit requires alternative mounting hardware, use commercially available hardware or contact Premier Mounts [phone].
M4 x 45mm (Qty 6)
M6 x 45mm (Qty 6)
M5 x 45mm (Qty 6)
M8 x 45mm (Qty 6)

Installation Instructions Page 5
LPSA3747
Wood Stud Installation
Step 3. Once the center of the stud has been
located and the wall plate is level, use a
pencil and mark the mounting hole
locations.
Before proceeding, remove the wall plate from the cover plate.
The end of the wall plate with the two
closely spaced holes should be pointing
up when mounting the wall plate. The flat
side of the wall plate will mount flush to
the wall.
Step 1. Determine the mount’s location on the
wall.
Step 2. Use a stud finder to locate the nearest
wall stud closest to your desired
location.
Stud
Electronic
Studfinder
Center Line Wall Plate
Positioning the Wall Plate
Front
View
Side
View
Mounting
Holes Wall
Side
Level
Step 4. Using a 1/8” drill bit and drill, pre-drill the
pilot holes where the first mark was made.
1/8” Drill Bit
Pilot Hole

Page 6 Installation Instructions
LPSA3747
Level
#14 x 2” Screws
Screwdriver
Step 5. Insert one (1) #14 X 2” screw into
the pre-drilled mounting hole.
Step 6. Tighten the top screw.
Step 7. Re-level the mount and make any
adjustments at this time. Step 8. Pre-drill the remaining three mounting
holes.
Step 9. Insert and tighten the remaining three
(3) #14 x 2” screws. Do not over-tighten
the screws.
Concrete Surface Installation
Concrete Bit
Level
Step 1. After leveling the wall plate mark all
four (4) mounting hole locations.
Step 2. Drill four (4) pilot holes using a
drill and a (commercially available)
concrete drill bit.
Level the wall plate before
proceeding.

Installation Instructions Page 7
LPSA3747
Step 5. Place the wall plate over the
wall anchors once the
wall anchors have been
correctly inserted into the
mounting surface.
Step 6. Using a screwdriver, insert
and tighten four (4) #14 x
2” screws.
Do not over-tighten the
wall anchors.
Screwdriver
Wall Anchor
Step 3. Once the holes have been
drilled, place the wall
anchors into the hole. Using
a hammer, gently tap into
place.
Make sure the mounting
surface area is smooth and
that the wall anchors are not
protruding from the wall.
Hammer
#14 x 2” Screws

Page 8 Installation Instructions
LPSA3747
Figure 1
Figure 2 Figure 3
Inverted Flat
Panel Display
Marking the
Depth
Thread Insert
Thread Depth
Indicator
Thread Depth
Indicator
Marking
Screw
Marking
Screw
Thread Depth
Indicator
Determining the Mounting Hardware
Step 1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the flat panel.
Step 2. Using a pencil, mark the depth of the thread insert on the thread depth indicator (Figure 2).
Step 3. Compare and verify the depth of the remaining thread inserts.
Step 4. Locate the correct diameter screw for the thread insert.
Step 5. Compare your thread depth indicator marking to the screw length.
When using the universal spacers in
the installation, make sure to account
for the appropriate spacing depth
when measuring with the thread depth
indicator. Using the universal spacers
will change the overall length of the
hardware used.
If your selected screw is longer than
the marking on the thread depth
indicator, do not use this screw. The
screw length must not bypass the
marking. If so, select another screw
size (Figure 2 and 3) until you find the
screw the comes closest to your mark
without going past the marking.
Universal Spacers Installation (optional)
The universal spacer may be stacked five (5) high, for a total stacking height of 1-1/4”. The universal spacers must be stacked in the
direction shown above. The universal spacers must be placed between the mounting bracket and the flat panel.
The universal spacer will fit M4, M5, M6 and M8 screws sizes.
Use the universal spacers to compensate for any indentations or recessed mounting points, if needed.

Installation Instructions Page 9
LPSA3747
Attaching the Flat Panel (75mm/100mm Mounting Points)
LPSA3747
Mounting Hardware
Universal Spacers (see NOTE)
Flat Panel
Mounting Hardware
Use the universal spacers to
compensate for any indentations
or recessed mounting points, if
needed.
Step 1. Fasten, to 1/2 the depth of the screws,
two (2) M4 x 10mm screws to the top
two mounting points on the flat panel.
Do not completely tighten these screws
at this time.
Step 2. Insert the head of the screws through
the keyhole slots on the cover plate.
Step 3. Insert and tighten the bottom two (2)
M4 x 10 Phillip screws to secure the
flat panel to the mount.
Step 4. Use a Phillips tip screwdriver to
tighten all mounting hardware.
Do not over-tighten the mounting
screws.
It is recommended that the flat
panel rest on a soft and flat
surface while the mount is
attached.
These installation steps should
be performed by two qualified
individuals.
If your flat panel comes with
75/100 mounting points on the
back (see illustration to the
right), the adapter plate will not
be used.
75/100 Mounting Points

Page 10 Installation Instructions
LPSA3747
LPSA3747 Installation
Step 1. The cover plate of the LPSA3747 must be
mounted to the wall plate that is attached to the
wall.
Step 2. The wall plate receptacle must be placed over
the top of the wall plate, so that the entire mount
“hangs” on the wall plate.
Step 3. Use the M3 Allen wrench (supplied) to tighten
the locking screw that is located on the bottom of
the mount base.
This locking screw will prevent the mount and flat panel
from being lifted off of the wall plate.
Failure to fully tighten the locking screw may
result in possible damage to your flat panel.
Locking Screw
M3 Allen
Wrench
Set Screw
Allen Wrench
Step 1. Once the viewing angle has been determined, use the 5/32” Allen
wrench to adjust the tilt/pivot adjustment screw.
The tilt/pivot adjustment screw comes pre-installed. The tilt/pivot
adjustment screw allows you to lock in the tilt/pivot viewing angle.
The final viewing angle will be determined once the flat panel has been
mounted on the wall.
Tilt/Pivot Adjustment
Rear Facing View

Installation Instructions Page 11
LPSA3747
Assembling the Adapter Plate
Step 1. Slide each mount arm onto the assembly plate
mounting rods.
Step 2. Insert four (4) M6 set screws into the mount arms
(two per arm). Use the M3 Allen wrench (supplied) to
tighten the set screws.
In the event that the mounting points on your flat panel exceed the standard 75/100 mounting pattern on the LPSA3747, the adapter plate
will have to be used. The adapter plate will accommodate mounting patterns of 600mm x 400mm.
Mount Arm
Assembly Plate
Assembly Plate Mounting
Rods
M3 Allen Wrench
M6 Set Screw - 4 Total
These screws should remain loose until the
adapter plate is attached to the display.
The illustration to the left shows
the two placement positions
for the mounting arms. Either
configuration is acceptable and
is dependant upon your flat
panel’s mounting hole pattern
Set Screw Mounting Point
Set Screw Mounting Point
Set Screw Mounting Point
Set Screw Mounting Point

Page 12 Installation Instructions
LPSA3747
The universal washer will fit M4, M5 M6 and M8 hole
patterns that your flat panel requires.
EXAMPLE: If your flat panel uses M8
screws, use the M8 mounting
points.
Universal Washer Installation
Pre-install the mounting screws, spacers and
washers. Once mounted, push down to
eliminate movement from the bracket. Then
proceed to tighten the rest of the hardware. Repeat
this process for the installation of the remaining
mounting bracket.
M4,M
M6
M8
5

Page 13 Installation Instructions
LPSA3747
Attaching the Adapter Plate to the Flat Panel
Step 1. Place the flat panel on a soft and flat surface.
Step 2. Locate the mounting holes that are on the back of the
flat panel.
Step 3. Place the mounting arms over the mounting points.
Step 4. Insert and tighten the mounting hardware using a
Phillips head screwdriver.
If your flat panel has uneven mounting points,
or recessed mounting points, please use the
provided universal spacers (please see page 8).
Please see page 8 on how to determine which
mounting hardware is most appropriate for your
flat panel.
Step 5. At this time, use an M3 Allen wrench and tighten the
M6 set screws that are located on the mounting arms
(four total).
Attaching the Flat Panel with the Adapter Plate
Use the universal spacers to
compensate for any indentations
or recessed mounting points, if
needed.
Step 1. Fasten, to 1/2 the depth of the screws,
two (2) M4 x 10mm screws to the top
two mounting points on the adapter
plate.
Do not completely tighten these screws
at this time.
It is recommended that the flat
panel rest on a soft and flat
surface while assembling the
mount.
LPSA3747
M4 x 10mm Phillips Head Screws
Adapter Plate
Flat Panel
Adapter Plate
Mounting Hardware
(see NOTE)
Universal Spacer
(see NOTE)
Mounting Point
Universal Washer

Installation Instructions Page 14
LPSA3747
M4 x 10mm Phillips Head Screws
Step 2. Insert the head of the screws through
the keyhole slots on the adapter plate.
Step 3. Insert and tighten the bottom two (2)
M4 x 10 Phillip screws to secure the
adapter plate to the mount.
Step 4. Use a Phillips tip screwdriver to
tighten all mounting hardware.
Do not over-tighten the mounting
screws.
LPSA3747 Installation with Adapter Plate
Step 1. The cover plate of the LPSA3747 must be
mounted to the wall plate that is attached to the
wall.
Step 2. The wall plate receptacle must be placed over
the top of the wall plate, so that the entire mount
“hangs” on the wall plate.
Step 3. Use the M3 Allen wrench (supplied) to tighten
the locking screw that is located on the bottom of
the mount base.
This locking screw will prevent the mount and flat panel
from being lifted off of the wall plate.
Failure to fully tighten the locking screw may
result in possible damage to your flat panel.
Locking Screw
M3 Allen
Wrench

Page 15 Installation Instructions
LPSA3747
Tension Adjustment
The mount shown in this illustration is upside down
to demonstrate how to access the adjustment nuts.
This unit comes pre-tensioned at the factory. To adjust the
swingout arm, perform the following steps:
Adjustment Nuts
Plastic End Caps
Top
Bottom
Step 1. Remove the plastic end caps.
Step 2. Take a socket (supplied) and ratchet and tighten/loosen
the nut to the desired tension.
Step 3. Replace the plastic end caps.
Cable Management
LPSA3747
Cable Tie
Cable
Flat Panel
Step 1. Route all cables along the LPSA3747.
Step 2. Use a cable tie to attach the cable to the LPSA3747 (as shown above).
Step 3. Cut off excess cable tie.
Before routing the cables and attaching the tie wraps, the LPSA3747 must be fully extended away from the wall.
Cable Access Ports
The cable access ports may be accessed by removing the plastic caps. The cable access ports allow you to route your
cables through the base of the LPSA3747 and into the wall.

Installation Instructions Page 16
LPSA3747
Technical Specification
All measurements are in inches(mm).

Page 17 Installation Instructions
LPSA3747
Warranty
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of
the original owner of this product. The limited warranty is valid only for the original purchaser of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is
defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will
be shipped to you at no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DIS-
PLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN
PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER
MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUD-
ING BUT NOT LIMITED TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOV-
ING AND REPLACING DEFECTIVE PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to
the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original con-
sumer purchaser must accompany all warranty claims. Warranty claims must also include a description of the
problem, the purchaser’s name, address, and telephone number. General inquiries can be addressed to Premier
Mounts Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or by fax.
Premier Mounts
Attn: Warranty Claim
3130 East Miraloma Ave.
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.