Panasonic WV-Q169E User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
Instructions
Ceiling Mount Bracket
Model No. WV-Q169E
ENGLISHDEUTSCHFRANÇAIS
ESPAÑOL
ITALIANOêìëëäàâ

2
All work related to the installation of this product should be made by qualified service
personal or system installer.
Use this apparatus for indoor use only.
Installation area
• Consult the dealer about the installation area to select a strong ceiling area. Make sure that
the installation area is strong enough to hold the total weight of the camera assembly
before installation.
Refer to the following about the weight of the camera assembly in accordance with the
model:
• WV-NW484S: approx. 2.2 kg
• WV-NW502S: approx. 2.15 kg
• WV-CW504S: approx. 2.05 kg
•WV-CW500S: approx. 2.25 kg
• The installation area shall have 210 mm or more space behind the ceiling.
• The thickness of the ceiling board for installation can range from 9 to 40 mm.
210 mm or more
Ceiling board: from 9 to 40 mm
CONTENTS
Preface ....................................................................................................................................... 2
Precautions ................................................................................................................................ 2
Major Operating Controls and Their Functions .......................................................................... 4
Installations ................................................................................................................................ 4
Specifications ............................................................................................................................. 9
Standard Accessories ................................................................................................................ 9
Precautions
Preface
The WV-Q169 is a ceiling embedded bracket that is exclusively designed to mount the color
CCTV camera: WV-CW504S, WV-CW500S, and Network camera: WV-NW484S, WV-NW502S,
on a ceiling. This bracket can be used for an area with weak pull-out strength such as plaster-
board in a double ceiling, and the embedded type makes the visible part of the camera small-
er.

3
Avoid installing in the following locations.
• Locations where it may get wet from rain or water splash
• Locations where a chemical agent is used such as a swimming pool (not only outdoor)
• Locations subject to steam and oil smoke such as a kitchen
• Locations where radiation or x-ray emissions are produced
• Locations where it may be damaged by briny air such as seashores
• Locations where the temperature is not within –30 °C to +50°C.
• Locations subject to vibrations (This product is not designed for on-vehicle use.)
• Locations where the temperature may rapidly change such as the peripheral areas of the
air outlets of air conditioners or doors facing outside. (In case of installing the camera in
such locations, the dome cover may become foggy or condensation may be caused on the
cover.)
Tightening the screws and bolts
• The screws and bolts must be tightened with an appropriate tightening torque according to
the material and strength of the installation area. After tightening the screws or bolts, per-
form visual check to ensure tightening is enough and there is no backlash.
• Required pull-out capacity of a single screw/bolt is 196 N or more.
Do not rub the edges of metal parts with your hand.
Failure to observe this may cause injury.
Be sure to remove this apparatus if it is not in use.
Be sure to install the safety wire.
Use the specified camera only.
Failure to observe this may cause a fall of an inappropriate camera resulting in injury or acci-
dents. Mount WV-CW504S, WV-CW500S, WV-NW484S, WV-NW502S on this bracket exclusive-
ly.
Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause a fall of the product resulting in injury.
Consult the dealer for the inspections.
ENGLISH

4
Major Operating Controls and Their Functions
WV-CW504S, WV-CW500S,
WV-NW484S, WV-NW502S
Roof space
Safety wire angle (Accessory)
Safety wire (Accessory)
* Read the manual of the camera as
well.
Installations
Be sure to read "Precautions" on the page 2 before installation. The manual of the camera, WV-
CW504S, WV-CW500S, WV-NW484S, WV-NW502S shall be read as well.
1. Put Template A (accessory) against the ceiling and make a hole.
qMake 4 holes of 12 mm in diameter.
wRemove the centre part from the tem-
plate.
eMake a hole of 180 mm in diameter.
The ceiling holes are shown
in the drawing at right. →
Ceiling face ø12 mm
(4 positions)
ø180 mm
Template A
Roof space

5
2. Install two anchor bolts (locally procured: M10 recommended) into the concrete ceil-
ing.
qInstall an anchor bolt in the
centre of the hole made in the
step 1.
wDetermine the anchor bolt
length by use of Template B
(accessory).
eUse Template B (accessory) to
decide the nut position, and fix
it.
(Mount the nut so that the dis-
tance between the bottom sur-
faces of the nut and ceiling is
adjusted to 134 mm.)
Note: If there is already an anchor bolt installed, the anchor bolt can be used as a 2nd anchor
bolt. Make sure that the distance between the 1st and 2nd anchor bolts is 1 000 mm or less
before use.
3. Mount the safety wire angle (accessory) on the 2nd anchor bolt and connect the safe-
ty wire (accessory) to the angle.
qDisconnect the safety wire from the safe-
ty wire angle.
wEngage the face marked qwith the
anchor bolt.
eBend the face marked w.
rConnect the safety wire to the safety wire
angle again.
Note: To use the anchor bolt that was already installed, the use of 2 spacer nuts (locally pro-
cured) is helpful.
Anchor bolts
Nut (locally procured)
Template B
Determine the anchor
bolt length
Ceiling board Install the anchor bolt in the centre
of the hole
134 mm
Upper side
Lower
side
Safety wire
wInsert
qDisconnect
eBend
Mark w
Mark q
rConnect
Safety wire angle
Anchor bolt
Spacer nuts
(locally procured)
Safety wire
Spacer nuts
Safety wire angle
Existing anchor bolt
2nd Anchor bolt
(locally procured) 1st Anchor bolt (locally procured)

6
Important: When securing this bracket on
the ceiling, make sure that the four ceil-
ing board fixing brackets are open as
shown in the following figure.
7. Use double nuts (locally procured) to
secure the mount bracket after insert-
ing the 1st anchor bolt.
8. Follow the procedure according to the
model of the camera to be installed.
<Installing WV-NW484S>
qUse the driver bit supplied with the cam-
era to remove the screws that secure the
camera enclosure and remove the enclo-
sure from the camera main body.
Important: Refer to the Operating inst-
ructions of the camera as well.
wPerform camera wiring.
eAlign the screw holes of the mount
bracket with the 4 mounting screws of
the camera main body and tighten them.
(Recommended tightening torque:
0.78 N·m)
4. Connect this mount bracket to the tip
of the safety wire.
5. Insert the 1st anchor bolt into the
mounting hole of the mount bracket.
6. Secure the mount bracket to the ceil-
ing board with the ceiling board fixing
screws (4 positions).
Turning the ceiling board fixing screws
clockwise provides ceiling board
tightening between the bottom of the
mount bracket and ceiling board fixing
bracket resulting in mount bracket
securing.
(Recommended tightening torque:
0.78 N·m)
Safety wire (Accessory)
Roof space
Insert the mount
bracket into the hole
Mount bracket
Mounting hole
1st anchor bolt
Ceiling
board fixing
screw
Ceiling board
fixing bracket
Turn clockwise
Double nuts (locally
procured)
Ceiling board

7
Note: The mount bracket supplied with
the camera is not used.
rMount the camera enclosure on the cam-
era main body.
<Installing WV-CW504S, WV-CW500S,
WV-NW502S>
qMount the camera attachment (supplied
with the camera) to this bracket.
Use 4 M4-L8 screws (supplied with the
camera) to secure the camera attach-
ment firmly as shown in the drawing.
(Recommended tightening torque: 0.78
N·m {0.58 lbf·ft})
wConnect the camera cables.
eAlign the “OPEN” mark of the camera
with the protrusion of the camera attach-
ment.
Engage the camera with the camera
attachment.
FRONT TOP
Bracket
Camera
attachment
M4-L8 screw
Screws of the main camera body
Ceiling mount
bracket
Screw
holes
LOCK
OPEN
FRONT TOP
Protrusion

8
rRotate the camera in the arrow direction
so that the protrusion of the camera
attachment is aligned with the "LOCK"
position to eliminate any backlash
between the camera and camera attach-
ment.
Engage the camera with the camera
attachment.
tUse the driver bit (supplied with the cam-
era) to loosen the screws that secure the
camera enclosure and remove the enclo-
sure from the camera main body.
Secure the camera to the camera attach-
ment with the camera fixing screw (red):
(Recommended tightening torque: 0.78
N·m {0.58 lbf·ft})
Important: The camera fixing screw shall be
securely tightened. Otherwise, water
exposure may cause damage or mal-
function of camera, or camera dropping
may result in injury.
(Recommended tightening torque: 0.78
N·m {0.58 lbf·ft})
yAdjust the camera.
Refer to the manual of the camera.
uUse the driver bit (supplied with the cam-
era) to tighten the screws that secure the
camera enclosure and mount the enclo-
sure on the camera main body.
9. Mount the decorative cover on this
mount bracket.
• Mount the decorative cover on the cam-
era mounting plate with engaging the
projections of the decorative cover with
the hooks for the decorative cover.
• Turn the decorative cover clockwise until
the cover clicks while pressing the cover
upward to lock the cover.
LOCK
OPEN
Protrusion
Enclosure
Camera fixing screw
Hooks for the
decorative
cover
Projections

9
Specifications
Ambient temperature –30 °C to +50 °C
Dimensions 204.4 mm in diameter x 143.4 mm in height
Weight Approx. 700 g
Finish Main body: Metal
Decorative cover: ABS resin with light silver coating

10
Standard Accessories
Instructions (this book) .................................. 1 pc.
The following are for installation.
Safety wire ..................................................... 1 pc.
Safety wire angle ........................................... 1 pc.
Template A .................................................... 1 pc.
Template B .................................................... 1 pc.
Decorative cover ........................................... 1 pc.
10