VidaBox VB VESA MNT FXSL User manual

7 Secure FXSL Mount onto Circular Retainer Piece
INSTALLATION GUIDE
Fixed Surface Lite VESA Mount
VB_VESA_MNT_FXSL
Ideal for VidaMount VESA Tablet Enclosures
VESA 100x100 Compatible
125 Newtown Rd, Ste 100
Plainview, NY 11803 USA
Toll-free US: (844) 4-KIOSKS
Worldwide: [phone]
Australia: [phone] VIDA
EU/UK: [phone] VIDA
B
A
B
Once aligned, place the Assembly onto the Circular Retainer [Step A].
Then, start rotating the assembly CLOCKWISE [Step B].
Eventually, you’ll hear a SNAP sound.
This conrms the FRONT spring is engaged and locked onto the assembly - we are ALL SET!
Spring Release Hole:
UNLOCKED Position
(Leans right-of-center)
ROTATE
CLOCKWISE
If the assembly is still loose, start again from Step 4.
Proper alignment is needed for the design to“lock” in place.
Front
Direction
(Center)
Spring Release Hole:
LOCKED Position
(Hole lines up and coincides
with front direction / center)
OPTIONAL : To Remove / Disassemble the FXSL Mount
B
C
B
ROTATE
COUNTER-
CLOCKWISE
To take apart the assembly:
Step A:
Step B:
Step C:
A
Insert and PUSH the L-shaped
Allen Key into the Spring Release Hole.
ROTATE COUNTER-CLOCKWISE to
loosen the FXSL Mount
The assembly will loosen -
lift up to remove the FXSL mount!

2 Run Cable through FXSL Mount
5 Locate the Spring Release 6 Align Mount to Circular Retainer
1 Install Circular Retainer Piece onto Table
Installation Instructions
Fixed Surface Lite (FXSL) Mount : VESA Compatible
Important Note:
If charging is desired, please prepare the extension cable and / or charging solution for the VESA device / enclosure rst.
Installing the charging solution / extension cable will be easier to do now rather than later.
VESA : 100 x 100mm (4" x 4") compatible. 75 x 75mm (3" x 3") compatible with Optional adapter [Sold separately]
Component Checklist:
FXSL Mount
[Main Assembly]
Countersink
Flat Head Screws
(4) x M4 x 16mm
Wood
Screws
(4) x M5 x 30mm
?
Using this with a VidaMount tablet enclosure?
Before proceeding: Install your
tablet & charging cable into the enclosure
FIRST - as per the included instructions.
Circular
Retainer Piece
4mm (1/6”)
wood bit
B. Mark the (4) top surface holes with a pencil,
using the Circular Retainer as a drilling template.
[Optional] Drill a 1” [25mm] hole in the
center, so that USB and/or other cables
can pass through the surface. C. Drill (4) x Wood Screws
through Circular Retainer & secure
it onto table/desk surface
L-Shaped
Allen Key
A. Place Circular Retainer at the center
of where the mount should be installed,
with the FRONT spring facing
the intended user.
3 Install VESA Device onto Mount
Feed USB or other
charging / data cables
through the
hollow core of
the mount now.
Flip the FXSL mount UPSIDE DOWN, then install
your VESA Device onto the mount, using the
(4) x M4x16mm Countersink Flat Head Screws.
After the VESA device
is secured onto the
Mount, look for a
small, half-oval on the
front of the Mount.
This is the
SPRING RELEASE.
Spring Release
(Half-oval, rounded front hole)
Hold the FXSL Mount above
the Circular Retainer Piece.
Angle the assembly’s
Spring Release so that it’s
pointing ~45º oset, to the
RIGHT of the FRONT spring.
~45º
4 Decide Where to Route the Cable(s) / Where do they Exit Out?
If Cable(s) CAN go through desk
Option A:
Route cable(s) and run them
through the centered exit
or Thru Hole.
If Cable(s) CANNOT go through desk
Option B:
Route cable(s) out the larger, pointy
(not rounded) rear exit hole in the back
1/16” [4mm]
wood bit
WIRE
GUIDE
WIRE
GUIDE
WIRE
GUIDE
Confirm Hole Locations
BEFORE drilling these pilot holes!
If the charging cable from
step 2 isn’t aligned with the
center of the FXSL mount,
use the built-in Wire Guides.
Route the cables
carefully and pull any
cable slack out of the
FXSL mount’s exit hole.
!
Flip mount UPSIDE
DOWN for this step
Installation is easier &
prevents damage to the
VESA device