Premier Mounts PSD-TS User manual

PLASMA STAND MODEL
I N S T A L L A T I O N M A N U A L
3130 E. Miraloma Ave. Anaheim, CA 92806 Phone: [phone] Fax: [phone]
www.mounts.com
PREMIER MOUNTS ©2004/ REV 00

- 2 -
oSafety & precautions
oFloor stand diagrams
oParts List
o(Optional) Accessories
oInstalling the Posts to the base
oSecuring the adapter
oInstalling the back plates
o(Optional) Shelf
o(Optional) Magnetic covers
oChecking for proper safety and security
When combined with a mount, our floor stand allows you to place a flat panel display in a horizontal or vertical position (with the PSM mount
only). The floor stand can be configured for single flat panel display. Height adjustable to any points along the stand’s vertical post to
achieve the perfect viewing height. The flat panel display then locks into place. The post also serves as a conduit for cabling.
The PSD-TS stand could mate directly to our CTM or PSM series of mounts.
Contents
Introduction

- 3 -
The entire installation instructions should be fully read and understood, including all of the safety symbols and safety precautions, before
beginning installation. The installation instructions should be read, understood and followed to prevent personal injury or property damage.
Keep these installation instructions in an easily accessible location for future reference.
Indicates that the power plug is to be disconnected from
the power outlet.
Safety precautions must be taken at all times.
Contact Premier Mounts for an
y
q
uestions
Warning and caution in general
Do not install in locations where there is vibration, movement or danger of impact. Failure to do so could result personal injury and
damage to the flat panel display.
Do not install near heater, fireplace, direct sunlight or air conditioning or any other source of direct heat energy. Failure to do so may
result in damage to the flat panel display and could cause a risk of fire.
At least two qualified people should always perform the installation work. Injury and damage can result from dropping or mishandling
the flat panel display.
Safety & Precautions
WARNING: Safety precaution measures must be practiced at all times during the installation of this product. Use proper safety gear and tools for the
installations procedure to prevent personal injury or damage to the flat panel display or mounts.
The floor structure should be capable of supporting a max weight of 160 Lbs., the weight of the flat panel display. More than 160 Lbs the
floor must be reinforced. Proper installation procedure by qualified personnel as outlined in the installations instructions must be adhered
to. Failure to do so could result in serious personal injury.
The maximum weight of the shelf is 25 lbs max load.

- 4 -
R33.89
R33.89
R24.39
19.68
14.75
29.50
.250
Ø.38 (X5)
27.22
R1.00
Ø.38
35.50
R24.39
60"
72"
84"
Our PSD-TS floor stands will mate directly with our CTM and PSM series mounts.
Floor stand diagrams
PSD-TS BASE
MATERIAL:
¼" Steel plate
COLOR:
Silver, Sinterflex gray
MATERIAL:
2" (dia) Posts
COLOR:
Chrome or Black
OPTIONAL POST SIZES
60" Height posts
72" Height posts
84" Height posts
NOTE: Use the four .38" diameter securing points to
secure the base to the floor.

- 5 -
oPhillips screwdriver, used on the PSM-Series and (optional) accessory shelf
o17 (mm) Socket head
oWrench
QTY SIZE DESCRIPTION
1 BASE
1 PSD-SPA ADAPTER
1 5/32" ALLEN WRENCH
2 M8 x 10 SOCKET HEAD SCREWS
4 M10 x 12 HEX HEAD SCREWS/ FLAT
WASHERS
1 M10 ALLEN WRENCH
Parts List
Accessories (Optional)
TOOLS & SUPPLY NEEDED
EQUIPMENT SHELF
MATERIAL: 12 (GA) CRS
MAGNETIC CABLE COVERS
MATERIAL: 18 (GA) CRS
PSD-SHA: Sinterflex Gray
PSD-SHP COLOR: Silver
CPA COLOR: Sinterflex Gray
CPB COLOR: Black
CPP COLOR: Silver
2" Posts
Magnetic
stri
p
s
Rear
cable covers
(optional)
Front
cable covers
Accessory overview
Equipment
Shelf assy
NOTE: The quantities of the
magnetic covers vary depending
on the height of the system that
was ordered.

- 6 -
(2) Inner tube
clam
p
s
(2) 2" Tubes
Allen wrench
PSD-TS Base
Installing the posts to the base
The PSM and CTM series mount is required to complete the PSD-CS system. Refer to its installation instructions to install the flat plasma display bracket.
The location of the stand must be a flat surface. Remove the stand out of the box and check for all proper hardware, if missing any hardware please call Premier Mounts.
Insert the tubes over the base columns making sure they are fully seated on the base and the cable access facing the rear of the base. Secure the tubes with two (2) of the M10 Socket
head screws with the hex key (supplied). Do not over tighten the hex screws. See figure 1.
(2) M10 Hex
screws
PSD-TS Base
(2) 2" Tubes

- 7 -
(2) 2" Tubes
PSD-SP
A
adapter
(2) M8 x 10
Hex screws
Allen wrench
Installing the back plate to the adapter
Install the PSD-SPA (stand adapter) through the top of the tubes and secure it to your desired height with the two (2) M8 x 10 Allen screws (supplied) found on the back of the
adapter. Use the 5/32" allen wrench (supplied) to secure the adapter to the posts. See figure 2.
NOTE: The back plate will vary depending on the system ordered. There are two (2) different systems for this stand PSM series and CTM series.
CAUTION: Arrow must be pointing up prior to installation. Secure the following plates to the secured PSD-SPA on the tubes.
For the PDB-UWFB (PSM-Series) secure the back plate to the four (4) threaded mounting points found on the PSD-SPA with the four (4) M10 x 12 bolts and flat washers (supplied).
For the CTM-Back plate (CTM-Series) secure the back plate to the four (4) threaded mounting points found on the PSD-SPA with the four (4) M10 x 12 bolts and flat washers
(supplied). See figure 3.
Installing the adapter to the posts
PDB-UWFB
Back plate
CTM
Back plate
(4) Flat washers
(4) M10 x 12 Hex
bolts
(2) 2" Tubes

- 8 -
CAUTION: The flat panel display is very heavy two people are required to lift the flat panel and secure it to the stand.
NOTE: To install the PSM-series or CTM-series mounting brackets to the flat panel refer to its installation instructions.
The flowing diagrams show the CTM and PCM series systems.
PSM-Series: Raise the flat panel display with the mounting bracket secured and insert the four (4) tab openings from the PSM mount to the four (4) receiving tabs found on the PDB-
UWFB back plate push the to slide the flat panel display down, right and down again to lock the mounts together. Make sure all tab openings are interlocked with the receiving tabs before
letting go of the flat panel. Secure the brackets with the two (2) M6 x 12 (mm) Phillip (supplied) screws for additional security.
CTM-Series: Raise the flat panel display with the left and right brackets secured to the plasma and insert the bottom and top hooks from the mounting arms to the top and bottom rods
found on the CTM back plate. Secure the mounting arms with the two (2) M6 x 12 Safety knobs (supplied).
CAUTION: The safety knobs MUST be used failure to do so may result in damage to the flat panel display or personal injury. See figure 4.
PSM
Series
CTM
Series
PSM-Back
plate
PSM-Series
mounting bracket
Flat panel
display
PSD-TS Base
Flat panel
display
CTM-Series
mounting
brackets
(2) M6 x 12
Safety knobs
CTM-Back plate
PSD-TS Base
Installing the plasma to the stand
Securing the base to the floor (Optional)
If securin
g
the base to the floor use
(
commerciall
y
available
)
suitable hardware de
p
endin
g
on the installation environment hardware,
PSD-TS Base
Suitable hardware
(commercially available)
(2) M6 x 12
Security
screws
1
2
3

- 9 -
1
2
3
4
5
CAUTION: Do not over tighten the M6 x 12 (mm)
Phillip security screw to the shelf.
NOTE: Do not install the shelf before the PSD-SPA.
The shelf must be added after the flat panel display has been installed to the stand. Install the shelf to the poles in a vertical position bypassing the poles then set the
shelf back to horizontal position. Install the shelf adapter as shown and secure the M6 x 12 (mm) Phillip screw. Set the desired height. The shelf adapter will secure
the shelf to the posts. See figure 5
(Optional) shelf installation
PSD-TS Base
Optional shelf
M6 x 12 Security
screw
If using the cable covers the optional shelf must be installed. Draw all your cables through the center of the posts and install the cable covers to the post. The magn-
etic strips will snap on the poles. The smallest cover (6") must always be installed above the shelf for cable management.
(Optional) Cable covers
PSD-TS Base
Magnetic covers
Flat panel display
6" Magnetic cover
Cables
Equipment shelf
Equipment shelf