Premio FlacheSAN1N8M-D4 User manual

Installation and service of this product should be conducted by trained
personnels to avoid any bodily injury from electric shock or heavy object
Observe ESD (Electrostatic Discharge) practices during integration to avoid
possible damage to the board and / or other components
FlacheSAN1N8M-D4 Quick Guide
Version 1.00 –2017.11.29
1. Check the content of the box. Please verify that
your package contains the following:
#
Description
Image / Description
Qty
1
Enclosure
1
2
Motherboard
Asrock EP2C612D16FM
1
3
OS drive
optional
1 or 2
4
CPU and memory
(optional)
Pre-installed upon request
2 sets
5
Heat sink
(optional)
2
6
Power Cable*
2
7
Slide Rail Kit (opt)
1
8
This Quick Guide
1
9
Packaging
1 set
* Inside the accessories box. If any items are missing, please contact
your authorized reseller or sales representative
2. Get familiar with the unit.
FlacheSAN1N8M-D4 is a 4-Bay NVMe storage server
supporting 8x M.2 NVMe modules, Intel Xeon E5-2600v3/v4
processor, front hot-swap low profile PCIe3 x8 NVMe cards,
up to 2x PCIe3 x16 expansion slots, and PCIe3 x8 IOM.
Front View
Rear View
NVMe Carrier
FlacheSAN1N NVMe carrier supports multiple M.2 module in
110mm and 80mm form factor NVMe such as SM951-NVme.
To hot swap the NVMe carrier, press the Power Off button,
wait until the button is completely off before replacing it.
3. Install M.2 NVMe modules to the carrier as
follows. One carrier supports two M.2 NVMe modules.
4. Install Expansion Card to the unit. Expansion
module support up to 2x PCIe3 x16 low-profile or full-height
cards.
5. Remove the top cover to install or inspect the
internal of the system.
Thank you for your purchase of FlacheSAN1N8M-D4, 1U 8x M.2 NVMe Haswell Server!

FlacheSAN1N8M-D4 Quick Guide
For more information please visit our website at www.premioinc.com
Copyright © 2017, Premio Inc. All rights reserved.
6. Inspect the internal of the system. By default, it
consists of an Asrock EP2C612D16FM Haswell Dual Processor
motherboard, a switch board, 3x blower modules. Optionally,
OS drive (up to 2x), IOM card (Gen3x8), M.2 modules (Gen3x4
each) and Expansion cards (Gen3x16 each) are installed by
request.
PSU
Switch
Board
OS Drive
x2
Blower
x3
Motherboard
NVMe #3 (top)
NVMe #4 (bottom)
NVMe #1 (top)
NVMe #2 (bottom)
Exp. card #1 (top)
Exp. card #2 (bottom)
CPU2
CPU1
2
IOM Card
2
NVMe #1, NVMe #2, and Expansion card #1 are associated
with CPU1. NVMe #3, NVMe #4, and Expansion card #2 are
associated with CPU2. IOM card is connected to CPU1.
7. Install CPU and memory (may be sold separately)
to their respective slots on the motherboard. Please be aware
of each component’s installation requirements and
prerequisites. Refer to the motherboard’s TPS for details.
Processor:
· Intel Xeon E5-2600/
4600 v3/v4 series CPU
· Dual Socket LGA 2011
R3
· Intel C612 Chipset
Memory:
· 16 DIMM slots
· Quad channel memory
· DDR4 2400*/2133/
1866/1600 RDIMM and
LRDIMM
· 1.2V
· RDIMM: 32, 16, 8, 4GB
· LRDIMM: 64GB, 32GB
* Only for E5-2600 v4
8. Install OS disk(s) into the bracket as follows:
1. Remove the OS disk bracket
2. Install the OS disk and
secure with M3 screws
(red circles)
3. Place the disk bracket assembly
back to the enclosure
4. Install the SATA and power cables to the disks
9. Replace the top cover. Once we are finished with
the internals of the system, close the top of the chassis.
1. Slide the cover back to the enclosure
2. Apply four 6-32 screws to secure the cover
10.Prepare rack mounting by installing inner rail to
the enclosure.
1. Install stand-offs (yellow circles) when necessary
2. Secure inner rail with M4x4L screw (red circle)
Install the outer rail to the rack. Use 6-32 x16L screws to
secure the rail (red circles –rear only).
1U
11. Mount the enclosure to the rack. Secure the
enclosure with 6-32 x16L by the ears.
1. Slide the inner rail of the enclosure
to the outer rail of the rack
2. Pull the latch (red circle) to
push the unit all the way
12. Plug in the power cords to the AC receptacles
on the back of the unit and secure it with the wire lock.
13. Press the power button on the
front of the unit after connecting a monitor
and input devices, and get ready for
software setup.