Premio FlacheSAN1N8U-D4 User manual

Installation and service of this product should be conducted by trained
personnels to avoid any bodily injury from electric shock or heavy object
Observe ESD (Electrostatic Discharge) practices during integration to avoid
possible damage to the board and / or other components
FlacheSAN1N8U-D4 Quick Guide
Version 1.10 –2017.03.03
1. Check the content of the box. Please verify that
your package contains the following:
#
Description
Image / Description
Qty
1
Enclosure
1
2
Motherboard
Asrock EP2C612D16FM
1
3
OS drive
optional
1 or 2
4
CPU and memory
(optional)
Pre-installed upon request
2 sets
5
Heat sink
(optional)
2
6
Power Cable*
2
7
Slide Rail Kit (opt)
1
8
This Quick Guide
1
9
Packaging
1 set
* Inside the accessories box. If any items are missing, please contact
your authorized reseller or sales representative
2. Get familiar with the unit.
FlacheSAN1N8U-D4 is a 8-Bay NVMe storage server
supporting Intel Xeon E5-2600v3/v4 processor, front hot-
swap low profile PCIe3 x4 NVMe disk in 2.5” form factor, up
to 2x PCIe3 x16 expansion slots, and PCIe3 x8 IOM.
Front View
Rear View
NVMe Carrier
FlacheSAN1N8U-D4 NVMe carrier supports 2.5” NVMe disk
drives such as Samsung XS1715, Intel 750 series.
3. Install NVMe drive to the carrier as follows. One
carrier supports one PCIe3 x4 NVMe disk in 2.5” form factor.
4. Install Expansion Card to the unit. Expansion
module support up to 2x PCIe3 x16 low-profile cards.
Thank you for your purchase of Premio FlacheSAN1N8U-D4, 1U 8x NVMe 2.5” SSD
Haswell Server!

FlacheSAN1N8U-D4 Quick Guide
For more information please visit our website at www.Premioinc.com
Copyright © 2017, Premio Inc. All rights reserved.
5. Remove the top cover to install or inspect the
internal of the system.
6. Inspect the internal of the system. By default, it
consists of an Asrock EP2C612D16FM Haswell Dual Processor
motherboard, a set of CPU and memory, a switch board, 3x
blower modules. Optionally, OS drive (up to 2x), IOM card
(Gen3x8), NVMe disks (Gen3x4 each) and Expansion cards
(Gen3x16 each) are installed by request.
NVMe #1 to #4 and Expansion card #1 are associated with
CPU1. NVMe #5 to #8, and Expansion card #2 are associated
with CPU2. IOM card is connected to CPU1.
7. Install CPU and memory (may be sold separately)
to their respective slots on the motherboard. Please be aware
of each component’s installation requirements and
prerequisites. Refer to the motherboard’s TPS for details.
Processor:
· Intel Xeon E5-2600/
4600 v3/v4 series CPU
· Dual Socket LGA 2011
R3
· Intel C612 Chipset
Memory:
· 16 DIMM slots
· Quad channel memory
· DDR4 2400*/2133/
1866/1600 RDIMM and
LRDIMM
· 1.2V
· RDIMM: 32, 16, 8, 4GB
· LRDIMM: 64GB, 32GB
* Only for E5-2600 v4
8. Install OS disk(s) into the bracket as follows:
1. Remove the OS disk bracket
2. Install the OS disk and
secure with M3 screws
(red circles)
3. Place the disk bracket assembly
back to the enclosure
4. Install the SATA and power cables to the disks
9. Replace the top cover. Once we are finished with
the internals of the system, close the top of the chassis.
10.Prepare rack mounting by installing inner rail to
the enclosure.
1. Install stand-offs (yellow circles) when necessary
2. Secure inner rail with M4x4L screw (red circle)
Install the outer rail to the rack. Use 6-32 x16L screws to
secure the rail (red circles, for rear posts only).
1U
11. Mount the enclosure to the rack. Secure the
enclosure with 6-32 x16L by the ears.
1. Slide the inner rail of the enclosure
to the outer rail of the rack
2. Pull the latch (red circle) to
push the unit all the way
12. Plug in the power cords to the AC receptacles
on the back of the unit and secure it with the wire lock.

FlacheSAN1N8U-D4 Quick Guide
For more information please visit our website at www.Premioinc.com
Copyright © 2017, Premio Inc. All rights reserved.
13. Press the power button on the front of the unit
after connecting a monitor and input devices, and get ready
for software setup.