Presidential Billiards LEGEND User manual

1
LEGEND BILLIARD TABLE INSTALLATION INSTRUCTIONS
Tools required by the installer:
3/8” Drive ratchet and Extension
1/2” Sockets for above
1/2” Combo end wrench
# 2 and # 3 Phillips screwdriver
Electric drill/ driver
1/8” & 3/16” Drill bits
Speed Square
Prior to installation of the table please check for damaged or missing parts. Call Presidential Billiards at
866-728-2253 if there is a problem. The assembly hardware is packed according to the steps below to
facilitate the cabinet assembly.
STEP 1 ASSEMBLE THE CABINET
1.1 Lay the cabinet panels upside down on a clean, flat, level surface.
1.2 Attach Leg braces to cabinet using bolt and washer from hardware pack.
1.3 Loosely assemble the legs to cabinet panels.
1.4 Place lower board in dowel holes while attaching legs.
1.5 Do not tighten at this time. Very Carefully Turn table over.
STEP 2 ATTACH BEAMS
2.1 Attach beam bracket to cabinet using bolt from hardware pack
2.2 Place beams in beam brackets.
2.3 Use bolt, square washer, round washer and nut from hardware pack, loosely fasten beam to
beam bracket.
2.4 Using a square, pull the beam flush with the top of the cabinet while making sure the bottom of
the beam in resting fully on the brace.
2.5 Tighten beam to the bracket. (Note: Long beam must be flush or slightly below short cross
beams or slate will not set level on table.)
2.6 Starting in one corner tighten bolts connecting cabinet to leg. (Use a square to make sure the
panels are flush with the top of the leg.)
2.7 Attach Slate blocks to long panels using bolt and washer from hardware pack.

2
STEP 3 LEVELING THE TABLE & INSTALLING THE SLATE
3.1 Place the cabinet in the desired location in the room.
3.2 Level the cabinet to the floor, shimming under the legs.
3.3 Set the 3 slate pieces in place and pre drill the slate screw holes into the slate support/wings
with a 3/16" drill bit. Level the table and slate combination with a spirit level both lengthwise
and cross wise, shimming as necessary.
3.4 Fasten the slate to the slate support/wings using the screws provided.
3.5 Fill the joints and install the bed cloth.
STEP 4 ASSEMBLING THE CUSHION RAILS & POCKETS
4.1 Remove the packaging from the cushion rails and apply the billiard fabric to the cushion rails.
Note: This step may have been completed before the table was delivered.
4.2 Lay out all the rails upside down and install the pockets using the bolts supplied. Keep the
rail/pocket joint as tight as possible.
WARNING: Use of non-Presidential Billiards pocket bolts will result in damaged rails.
4.3 Having bolted the U frame rails together turn the rail and pocket assembly right side up and
place on the table.
Caution: Be very careful at this point to avoid cracking a rail.
STEP 5 INSTALLING THE CUSHION RAIL / POCKET ASSEMBLY
5.1 Align the rail/pocket assembly and loosely bolt it to the slate surface using the bolts and dome
washers provided.
5.2 Align the rail/pocket assembly to the slate and tighten the bolts by hand. (No power tools
please!)
WARNING: Do not over tighten!
Should there be any problems please contact us at:
Presidential Billiards, L.P. Tel: [phone]
20221 Carolina Way Fax: [phone]
New Caney, TX 77357 Revised: 6/15/15

3
Legend Billiard Table Hardware
STEP 1
STEP 2
2.1
24
5/16 –18 x ¾” Flange Bolt
NU3960
8
Beam Brackets “L” shape
NE90702
2.3
8
5/16 - 18 x 3 ½” bolts
NU00961
8
5/16 Flat Washer
NE3526
8
5/16 Dome Tooth Washer
NE3648
8
5/16 - 18 hex nuts
NU0012
2.7
8
5/16 –18 x 2” Bolt
NU4915
8
5/16 Flat Washer
NE3526
STEP 3
3.4
17
# 14 x 2 ½” Slate screws
NU3940
STEP 4
4.2
12
5/16 –18 x 3/4” Phillips head bolts
NU3971
STEP 5
5.1
18
3/8 –18 x 2” Bolts
NU3950
18
3/8” Dome washers
NE3527
1.2
16
5/16 Flat Washer
NE3526
16
5/16 –18 x 1 ½” Bolt
NU1092
1.3
16
3/8 –16 x 2 3/4" bolt
NU4914
16
3/8 Heavy duty washers
NE46481