Pridiom AOS090HR User manual

1
* Selection of installation positions for indoor unit *
*To be installed at the position where the air delivered from the unit can reach every corner of
the room;
*To avoid being affected by the outdoor air;
*To avoid blockage to the air inlet or outlet of the unit;
*To avoid too much oil smoke or steam;
*To avoid possible generation, inflow, lingering or leakage of flammable gases;
*To avoid high-frequency facilities (such as high frequency arc welders, etc.);
*To avoid the places where acid solutions are frequently used;
*To avoid the places where some special sprayers (sulfides) are frequently used.
*Not to install a fire alarming device near the air outlet of the unit (during operation, the fire alarm
device might be erroneously triggered by the warm air from the unit);
Above 100mm(4")
Left side: 150mm(6")
and above
Right side: 150mm (6")
and above
Ceiling
Wall hanging plate
ground
2300mm(7'6")
and above
* Make sure of enough space for installation and maintenance.
*To take into consideration the operational convenience and safety in installation, it is recommended
to ensure enough space between the unit and the walls.
* Height limits of indoor and outdoor units.
*Either the indoor unit or the outdoor unit can be higher, but the height difference must comply the stated
requirements.
*Try to reduce the bending of the piping line as much as possible so as to avoid possible negative impacts upon the
performances of the units.
Indoor unit
outdoor
unit
5m(16'5")max.
INSTALLATION & REPAIR GUIDE
Split Wall-Mounted Air Conditioner

2
* Selection of installation positions for outdoor unit *
*To install the outdoor unit at the places which can stand the load of the machine weight and will
not cause big vibrations and noises;
*To install the unit at the places not to be exposed to rain or direct sunshine, and the places with
good ventilation;
*The noises generated from the unit will not affect the neighboring places;
*Do not install the unit on non-metal frame;
*Not to install the unit at the places where there might occur the generation, inflow, stay or
leakage of inflammable gases;
*Pay attention to the drainage of the condensed water from the base plate during operations;
*To avoid the air outlet being directly against the wind.
Detailed space requirements around the outdoor unit
1. When there are obstacles above
the unit 2. When the front (air outlet) is open 3. When there are obstacles only in
the front (air outlet)
4. When there are obstacles at the front and rear sides.
5. When there are obstacles all around
the unit on four sides.
Although the top side is open, the
installation is not to be done if there
are obstacles all around.
Space for maintenance
Shown as in the following figure. Keep
the maintenance space in front of the
unit.
500mm(1'8") min
100mm(4") min
500mm(1'8") min
200mm(8") min
500mm(1'8") min
500mm
(1'8")min
200mm
(8")min
Space for maintenance
*At least two sides should
be kept open.
200mm(8") min
300mm(1') min
1000mm(3'4") min
100mm(4") min
INSTALLATION & REPAIR GUIDE
Split Wall-Mounted air conditioner

3
* Installation fixture of indoor unit *
INSTALLATION & REPAIR GUIDE
Split Wall-Mounted air conditioner
1.Installation of wall-mounting plate
Fix the wall-mounting plate firmly on the wall with screws.
Make sure of the leveling of the plate. Slanted wall-mounting
plate might jeopardize the smooth discharge of the condensed
water.
2.Drill holes on the wall
3.Installation of drain pipe
Install the pipelines of the indoor unit in accordance with
the direction of the wall holes. Wrap tightly the drain pipe
and the pipelines with tape. Make sure that the drain pipe
is underneath the pipelines. (Fig.3) (When the drain pipe
passes the room interior, some condensed water might
occur to its surfaces if the humidity is very high).
4.Installation of indoor unit
Pass the connection wires, connecting pipelines and drain
pipe through the wall hole. Hang the indoor unit on the
hooks at the top of the wall-mounting plate so that the
hooks at the bottom of the indoor unit match the hooks of
the wall-mounting plate. (Fig.4)
Fig.2
Fix with a tape
Wall cap Wall pipe
Interior Exterior
5-10mm lower
(1/5-2/5")
Wall
Fig.3
Pipelines of indoor unit
Drain pipe
Rear pipe
Bottom hooks
Hook supports
Top hooks
Fig.4
Drill holes at places slightly below the wall-mounting plate,
with hole diameter of 65mm(2-3/5") and the outer edge of
the hole 5-10mm(1/5-2/5") lower (Fig.2) so that the condensed
water can smoothly flow out. Cut the wall penetrating pipe
to proper length according to the thickness of the wall (3-
5mm(1/10-1/5") longer than the wall thickness) and insert
the pipe as indicated in Fig.2.