Priefert LOG22 User manual

ASSEMBLY& OPERATING INSTRUCTIONS
LS123-806-0909
Rev 0
THIS SAFETY ALERT SYMBOL IDENTIFIES IMPORTANT SAFETY MESSAGES IN THIS MANUAL
Owner’s Manual
MODEL NO. LOG22
22 TON
MODEL NO. LOG28
28 TON
MODEL NO. LOG34
34 TON
VERTICAL/HORIZONTAL
LOG SPLITTERS

Table of Contents
Page(s)
Important Safety Information................................................................................................................. 1-6
Intended Use ......................................................................................................................... 1
Personal Protective Equipment ............................................................................................... 1
Safety Decals ....................................................................................................................... 1-2
General Safety ...................................................................................................................... 3
Preparation of the Log ........................................................................................................... 3
Work Area ........................................................................................................................... 3
Operation of the Log Splitter .................................................................................................. 3-4
Repair and Maintenance Safety ............................................................................................. 4
Hydraulic Safety .................................................................................................................. 5
Fire Prevention ..................................................................................................................... 5-6
Towing Safety ...................................................................................................................... 6
Assembly Instructions ...................................................................................................................... 7-19
LOG22 ................................................................................................................................ 7-9
LOG28 ................................................................................................................................ 11-13
LOG34 ................................................................................................................................ 16-19
Operating Instructions ....................................................................................................................... 22-23
Engine Oil Recommendations ................................................................................................ 22
Starting Instructions ............................................................................................................... 22
Towing .................................................................................................................................. 23
Operation .............................................................................................................................. 9
Maintenance ...................................................................................................................................... 23
Parts Lists .........................................................................................................................................
LOG22 ................................................................................................................................. 9-10
LOG28 ................................................................................................................................. 14-15
LOG34 ................................................................................................................................. 20-21
Notes ................................................................................................................................................ 24
Specifications .................................................................................................................................. Back Cover

WARNING: Read and thoroughly understand all instructions and safety information before assembling
or operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone
to operate this log splitter who has not read this manual. As with all power equipment a log splitter
can be dangerous if assembled or used improperly. Do not operate this log splitter if you have doubts
or questions concerning safe operation. Call our customer service department at 1-800-527-8616 to
address these concerns.
Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.
NEVER use this log splitter for any other purposes than splitting wood. It is designed for this use only.Any other use can
cause serious injury or death.
PEPER
PERPERSONALSONAL PROTECTIVE EQUIPMENT
BEFORE operating this log splitter make sure that you wear safety gear such as goggles or safey glasses, steel toed
shoes and tight fitting gloves (without loose cuffs or draw strings). Always wear a protective hearing device when operat-
ing this log splitter.
NEVER wear loose clothing or jewelry that can be caught by moving parts of the log splitter. Keep clothing and hair away
from all moving parts when operating this log splitter.
PERSONAL PROTECTIVE EQUIPMENT
SAFETY DECALS
Make sure that all safety warning decals are in good condition and readable. Always replace missing or defaced decals.
Write us or call 1-800-527-8616 and they will be sent to you at no charge.
DL-52-8
DL52-2-8
INTENDED USE
Page 1
PARTNUMBER: 52020000
LOCATION: TOP, FRONT END OF TONGUE

Page 2
PARTNUMBER: 51018900
LOCATION: TOP OF HYDRAULIC CYLINDER
PARTNUMBER: 52023200
LOCATION: HYDRAULIC TANK
LOWER TANK, RIGHT CORNER
PARTNUMBER: 52055200
LOCATION: TOP, FORWARD
SECTION OF CYLINDER AND
SIDES OF STRIPPER PLATES

GENERAL SAFETY
EVER
NEVER allow children or adults lacking proper instructions and understanding to operate this log splitter.
KEEP all people and pets a minimum of 10 feet away from your work area when operating this log splitter. Only the
operator is to be near the log splitter during use.
If a helper is assisting in loading logs, NEVER actuate the control until the helper is clear of the work area.
NEVER operate the log splitter when under the influence of alcohol, drugs or medication.
NEVER allow a person who is tired or otherwise not alert to use your log splitter.
PREPARATION OF THE LOG
Both ends of the log should be cut as square as possible to help prevent the log from riding out of the splitter during
operation. Do not split logs greater than 26 in. in length.
WORK AREA
NEVER operate the log splitter on slippery, wet, muddy or icy ground.
ONLYoperate your log splitter on level ground. Operating on a slope could cause the log splitter to roll over or logs to fall
off.
NEVER operate your log splitter in an enclosed area. Exhaust fumes contain carbon monoxide which can be deadly when
inhaled.
NEVER attempt to move your log splitter over hilly or uneven terrain without a tow vehicle or adequate help.
ALWAYS block the wheels to prevent movement of the log splitter while in operation.
ONLYoperate your log splitter in daylight or under good artificial light.
ALWAYS keep the work area clean. Remove split wood around your log splitter immediately so that you don’t stumble
over it.
OPERATION OF THE LOG SPLITTER
ONLY operate the log splitter from the operator zone* as
shown in the diagrams. The operator has the safest and
most efficient access to the control valve and beam in
this
location. Failure to operate the log splitter in this location
can result in serious injury or death.
*Shown in horizontal position Page 3
Failure to follow these instructions may result in serious injury or death.
Operator
Zone LOG22 MODEL
ENGINE
TONGUE
BEAM
FOOT PLATE ENGINE
BEAM
TONGUE
Operator
Zone
LOG28 & LOG34
MODELS

KNOW how to stop the log splitter and disengage the controls before operating it.
NEVER place hands or feet between the log and splitting wedge during forward or reverse stroke. Serious injury or death
could result.
NEVER straddle or step over the log splitter during operation.
NEVER reach or bend over the log splitter to pick up a log.
NEVER try to split two logs on top of each other.
NEVER try to cross split a second log.
NEVER allow one person to operate the valve while another is positioning the log.
NEVER attempt to load your log splitter when the ram or wedge is in motion.
ALWAYS use your hand to operate the control lever on the valve. NEVER use your foot, a rope or any extension device.
NEVER move the log splitter while the engine is running. Shut off the engine even if you are leaving the log splitter for a
short period of time.
ALWAYS avoid contact with the muffler and other hot areas of the engine during operation to prevent burns.
REPAIR AND MAINTENANCE SAFETY
NEVER operate your log splitter when it is in poor mechanical condition or in need of repair.
Periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamps are tightened.
NEVER alter your log splitter in any manner such as adding a rope or extenstion to the control lever or adding to the
width or height of the wedge. Such alterations may cause your log splitter to be unsafe and will void the warranty.
Perform all recommended maintenance procedures before using your log splitter.
Replace all damaged or worn parts immediately.
NEVER tamper with the engine to run it at excessive speeds. The maximum engine speed is preset by the manufacturer
and is within safety limits.
ALWAYS remove the spark plug wire before performing any service or repair on your log splitter.
ALWAYS check the level of hydraulic oil and engine oil before operation.
ALL replacement parts must meet manufacturer’s specifications.
Page 4

HYDRAULIC SAFETY
The hydraulic system of your log splitter requires careful inspection along with the mechanical parts. Be sure to
replace frayed, kinked, cracked or otherwise damaged hydraulic hose and components.
NEVER check for leaks of hydraulic fluid with your hand. Fluid escaping from a small hole can be almost invisible.
Escaping fluid under pressure can have sufficient force to penetrate skin causing serious personal injury or even death.
Leaks can be detected by passing a piece of cardboard over the suspected leak and looking for discoloration.
ALWAYS seek professional medical attention immediately if injured by escaping hydraulic fluid. Serious infection or
reaction can develop if proper medical treatment is not administered immediately.
ALWAYS be sure to relieve all pressure by shutting off the engine and moving the valve control handle back and forth
should it become necessary to loosen or remove any hydraulic fitting.
NEVER remove the cap from the hydraulic tank or reservoir while the log splitter is running. Hot oil under pressure
could result in serious injury.
NEVER adjust the hydraulic valve. The pressure relief valve on your log splitter is preset at the factory. Only a qualified
service technician should perform this adjustment.
FIRE PREVENTION
NEVER operate your log splitter near a flame or spark. Hydraulic oil and gasoline are flammable and can explode.
NEVER fill the gas tank while the engine is hot or running. Allow the engine to cool before refueling.
NEVER smoke while operating or refueling your log splitter. Gas fumes can easily explode.
ONLYrefuel your log splitter in a clear area with no gas fumes or spilled gas.
ALWAYS use an approved fuel container.
ALWAYS replace the gas cap securely.
If gasoline has spilled, move the log splitter away from the area of the spill and avoid creating any source of ignition
until the spilled gas has evaporated.
ALWAYS take a Class B fire extinguisher with you when operating this log splitter in dry areas as a precautionary
measure against possible flying sparks.
ALWAYS drain the fuel tank prior to storage to avoid the potential fire hazard.
ALWAYS store gasoline in an approved, tightly sealed container. Store the container in a cool, dry place.
NEVER store gasoline in the house or near a heating appliance.
Page 5

IMPORTANT NOTE:
This log splitter is equipped with an internal combustion engine and should not be used on or near any unimproved
forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark ar-
rester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in efffective
working order by the operator. In the state of California a spark arrester is required by law. Other states have similar laws.
Federal laws apply on federal lands. Aspark arrester muffler (optional by manufacturer) is available as an accessory at
your nearest engine dealer. Always check the legal requirements in your area.
TOWING SAFETY
ALWAYS check all local and state regulations regarding towing, licensing, and lights before towing your log splitter.
ALWAYS check before towing to make sure that the log splitter is correctly and securely attached to the towing vehicle
and that the safety chains are secured to the hitch or bumper of the vehicle with enough slack to allow turning. Always
use a Class I, 2” ball with this log splitter.
NEVER carry any cargo or wood on your log splitter.
NEVER allow anyone to sit or ride on your log splitter.
ALWAYS disconnect your log splitter from the towing vehicle before operating it.
ALWAYS be careful when backing up with your log splitter in tow. It could jackknife.
ALWAYS allow for added length of your log splitter when turning, parking, crossing interesections and in all driving
situations.
NEVER exceed 45 mph when towing your log splitter. Towing the log splitter at speeds higher than 45 mph could result in
loss of control, damage to the equipment, serious injury or death. Adjust towing speed for terrain and conditions. Be
extra cautious when towing over rough terrain especially railroad crossings.
Page 6

ASSEMBLYINSTRUCTIONS LOG22
NOTE: This log splitter was partially assembled at the factory. Refer to the drawings and parts list should it become neces-
sary to disassemble the unit for repair or replacement of parts
1401411B22 Beam Assembly 1
2401193B22 Tank/Engine Assembly 1
3400312B0 Tire and Wheel assembly 2
440126300 Tongue Assembly 1
40115500 Hardware Kit 1
STEP 1: Remove all the components from the shipping container.Inspect each piece for shipping damage. If any part is
damaged, contact your dealer or delivering carrier.
STEP 2: Attach the two wheels (2) to the tank assembly (1) wheel spindles using the 3/4” light flat washers(3) ,3/4” NF
slotted nuts (4), 1/8” x 1-1/2” cotter pins (5) and the hub caps (6). These items are in the hardware package.
Tighten the slotted nuts and make sure the wheels rotate freely.
ITEM NO. PART NO. DESCRIPTION QTY.
1401193B22 Tank Assembly 1
2400312B0 Wheel Assembly 2
3O/L 3/4” Light Flatwasher 2
417012000 3/4” Slotted Nut 2
5O/L 1/8*’ x 1-1/2” Cotter Pin 2
640033200 Hub Cap 2
Page 7
O/L- Obtain locally. Common fasteners available through hardware
and farm stores.

STEP 3: Attach the tongue assembly (5) to the tank assembly (4) using two 1/2” NC x 4-1/2” hex cap bolts (1), two 1/2” lock
washers (2) and two and two 1/2” hex nuts. Tighten. (3).Tighten.
ITEM NO PART NO. DESCRIPTION QTY.
1O/L 1/2”NC x 4-1/2” Bolt 2
2O/L 1/2” Lock Washer 2
3O/L 1/2” NC Hex Nut 2
4401193B22 Tank Assembly 1
540126300 Tongue Assembly 1
STEP 4: Stand the beam (1) up on end. Two people may be needed for this step to ensure safety. Make sure that the beam
is stable and on a level surface.Remove the pivot pin (2) and clip pin (3) from the tank assembly.Roll the tongue/
tank assembly into position between the two tabs on the beam (1). Slide the pivot pin (2) through the aligned holes
and lock in place with the clip pin (3)
ITEM NO. PART NO. DESCRIPTION QTY.
1401411PB Beam 1
2071022WC Pivot Pin 1
3O/L 1/2”-3/4” R Clip Pin 1
Page 8
O/L- Obtain locally. Common fasteners available through hardware
and farm stores.
O/L- Obtain locally. Common fasteners available through hardware
and farm stores.

Page 9
STEP 5: Connect the end of the 1/2” ID x 44” hydraulic pressure hose (1) coming from the fitting on the pump to the fitting
on the valve . See illustrations below.
STEP 6: Slide one hose clamp on the end of the 3/4” x 44” hydraulic return hose (3) that comes from the fitting on the
filter . Then connect the hose to the fitting on the valve. See illustrations below.
TANK/ENGINE ASSEMBLYBREAKDOWN
Area of
Detail
View from Top
ITEM NO. PART NO. DESCRIPTION QTY.
139024600 1/2” x 44”Pressure Hose 1
239031600 Worm Gear Clamp 3
339025200 3/4” x 44” Return Hose 1
4390406SC Auto-Return Valve 1
5
ITEM NO. PART NO. DESCRIPTION QTY.
1O/L 5/16”-18 UNC Nylock Nut 7
2O/L 5/16” x 2-1/2” GR 5 Hex Bolt 1
3 O/L 5/16” x 1 GR5 Hex Bolt 4
4O/L 5/16” x 1-1/2” GR5 Hex Bolt 2
539024600 1/2” x 44” Hydraulic Pressure Hose 1
639025200 44” Return Hose 1
739026800 3/4” x 12” Suction Hose 1
839032000 3/4” NPT x 3/4” Tube Fitting 1
939034100 1/2’” Street Elbow 1
10 39034900 3/4” Hex Nipple 1
11 39038300 Straight Pipe Fitting; 3/4” NPT to 1
3/4” ID Tube
12 39052900 190cc Briggs & Stratton Engine 1
13 39060400 Filter Assembly 1
14 390705B0 11 GPM Pump 1
15 39031600 Worm Gear Clamp 3
16 40032100 3/16” x 1-1/2” Square Key 1
17 40117400 Grommet 1
18 401193B Tank 1
19 400833L0 Jaw Coupler , 1/2” Bore 1
20 400834L0 Rubber Spider 1
21 400838L0 Jaw Coupler, 7/8” Bore 1
22 071022WC Pivot Pin 1
23 07092400 1/2”-3/4” Hairpin Cotter 1
24 3903750 BreatherCap/Dip Stick 1
25 390604B Filter Base 1
O/L- Obtain locally. Common fasteners available through
hardware and farm stores.
O/L- Obtain locally. Common fasteners available through
hardware and farm stores.

TONGUE ASSEMBLYBREAKDOWN
ITEM NO. PART NO. DESCRIPTION QTY.
1O/L M10 x 1.5 Nylock Nut 3
2O/L M10 x 1.5 x 100mm GR5 Bolt 1
3O/L M10 x 1.5 x 120mm GR 5 Bolt 1
4O/L M10 x 1.5 x 90mm Gr5 Bolt 1
5O/L M10 Flat Washer, narrow 2
607095800 5/16” Square Lock Pin 1
707080900 Stabilizer Pin Assembly 1
840034600 Hitch Ball Assembly 1
9O/L M10 Flat Washer 6
10 40126100 Tongue 1
11 40126000 Ground Stand 1
12 40032300 20 Link Chain with Hook 2
BEAM ASSEMBLYBREAKDOWN
ITEM NO. PART NO. DESCRIPTION QTY.
1O/L 1/2” X 3-1/4” GR 5 Hex Cap Bolt 1
2O/L 1/2” Regular Lock Washer 1
3O/L 1/2” Hex Nut 1
4401411PB Beam 1
5 40141700 Wedge 1
6 390118BC 4” Cylinder 1
707073100 Cylinder Pin 1
8 390406SC Valve 1
9 39034700 1/2” Pipe to Steel To Steel Tube 2
10 39034300 1/2” NPT Nipple 1
11 39032000 3/4” NPT x 3/4” Tube Fitting 1
12 39039000 45° Fitting, 3/4” Male, 1/2” Female 1
13 39034600 1/2” Steel Tube 1
O/L- Obtain locally. Common fasteners available through
hardware and farm stores.
O/L- Obtain locally. Common fasteners available through
hardware and farm stores.
Page 10

ASSEMBLYINSTRUCTIONS LOG28
NOTE: This log splitter was partially assembled at the factory. Refer to the drawings and parts list should it become neces-
sary to disassemble the unit for repair or replacement of parts
STEP 1: Remove all the components from the shipping container.Inspect each piece for shipping damage. If any part is
damaged, contact your dealer or delivering carrier.
STEP 2: Attach the two wheels (2) to the tank assembly (1) wheel spindles using the 3/4” light flat washers(3) ,3/4” NF
slotted nuts (4), 1/8” x 1-1/2” cotter pins (5) and the hub caps (6). These items are in the hardware package.
Tighten the slotted nuts and make sure the wheels rotate freely.
1401612PB Beam Assembly 1
240127500 Beam Lock Assembly 1
3401609PB Tank Assembly 1
4400312B0 Tire and Wheel 2
540127300 Tongue Assembly 1
40115400 Hardware Kit 1
ITEM NO. PART NO. DESCRIPTION QTY.
1401609PB Tank Assembly 1
2400312B0 Wheel Assembly 2
3O/L 3/4” Light Flatwasher 2
417012000 3/4” Slotted Nut 2
5O/L 1/8*’ x 1-1/2” Cotter Pin 2
640033200 Hub Cap 2
Page 11

STEP 3: Attach the tongue assembly (5) to the tank assembly (1) using two 1/2” NC x 4-1/2” hex cap bolts (2), two 1/2” lock
washers (3) and two and two 1/2” hex nuts (4). Tighten.
STEP 4: Stand the beam (1) up on end. Two people may be needed for this step to ensure safety. Make sure that the beam
is stable and on a level surface. Remove the pivot pin (3) and clip pin (2) from the tank assembly.Roll the tongue/
tank assembly into position between the two tabs on the beam (1). Slide the pivot pin (3) through the aligned holes
and lock in place with the clip pin (2)
ITEM NO. PART NO. DESCRIPTION QTY.
1401609PB TankAssembly 1
2O/L 1/2” NC x 4-1/2 Hex Bolt 2
3O/L 1/2” Lock Washer 2
4O/L 1/2” NC Hex Nut 2
540127300 Tongue Assembly 1
ITEM NO. PART NO. DESCRIPTION QTY
1401413PB Beam 1
2O/L 1/2”-3/4” R Clip Pin 1
3071022WC Pivot Pin 1
Page 12

STEP 5: Connect the end of the 1/2” ID x 44” hydraulic pressure hose (1) coming from the fitting on the pump to the fitting
on the valve. See illustrations below.
STEP 6: Slide one hose clamp on the end of the 3/4” x 44” hydraulic return hose (2 ) that comes from the fitting on the
filter. Then connect the hose to the fitting on the valve. See illustrations below.
STEP 7: Attach the latch (3) to the bottom side of the beam as shown in the diagram using the two 1/2” x 1-1/4” Grade 5
hex cap bolts (4), the two 1/2” lock washers (1) and the two 1/2” hex nuts (2 ). Lower the beam onto the
tongue.Position the latch assembly on the tongue and tighten hardware.
ITEM NO. PART NO. DESCRIPTION QTY.
1O/L 1/2” Lock Washer 2
2O/L 1/2” Hex Nut 2
340127500 Beam Lock 1
4O/L 1/2” x 1-1/4” Bolt 2
4
Area of
Detail
Page 13
DETAIL A
SCALE 1:3
ITEM NO. PART NO. DESCRPTION QTY.
139027500 1/2” X 38” Pressure Hose 1
239027400 3/4” x 56” Return Hose 1
339031600 Worm Gear Clamp 3

ITEM NO. PART NO. DESCRIPTION QTY.
1O/L 5/16”-18 UNC Nylock Nut 4
2O/L 5/16” Flat Washer 8
3O/L 5/16” x 1-1/2” GR5 Hex Bolt 4
439027400 Return Line Hose 1
539027500 1/2” x 38” Hydraulic Pressue Hose 1
639032000 3/4” NPT x 3/4” Tube 1
739034900 3/4” Hex Nipple 1
839038100 Straight Fitting, 3/4”NPT to 1/2” Tube 1
939038900 1” ID Suction Hose 1
10 39060400 Filter Assembly 1
11 39073200 Briggs & Stratton 1350/Pump Assy.1
12 39031600 Worm Gear Clamp 3
13 401188PB Tank 1
14 071022WC Pivot Pin 1
15 O/L 1/2”-3/4” Hairpin Cotter 1
16 3903750 Dip Stick/Breather Cap 1
17 390601A0 Filter Element 1
O/L- Obtain locally. Common fasteners available through hardware
and farm stores.
PUMP/ENGINE ASSEMBLYBREAKDOWN
ITEM NO. PART NO. DESCRIPTION QTY.
1O/L 5/16”-18 UNC Nylock Nut 4
2O/L 5/16” Regular Lock WAsher 4
3O/L 5/16” x 1-1/4”GR5 Hex Bolt 4
4O/L 5/16” x 1 UNF GR5 Hex Bolt 4
539054500 Briggs & Stratton 1350 Engine 1
640034300 1/4” Square x 1-1/2” Square Key 1
740081800 Pump Mount 1
8400825L0 Jaw Coupler 1” Bore 1
9400826L0 Jaw Coupler 1/2” Bore 1
10 400827L0 Rubber Coupler Spider 1
11 39070900 16 GPM Pump 1
TANK/ENGINE ASSEMBLYBREAKDOWN
Page 14

BEAM ASSEMBLYBREAKDOWN
ITEM NO. PART NO. DESCRIPTION QTY
1O/L 1/2” Hex Nut 1
2O/L 1/2” Regular Lock Washer 1
3O/L 1/2” x 3-1/4” Hex Bolt 1
4390119B0 4.5” x 24” Hydraulic Cylinder 1
539032000 3/4” NPT x 3/4” Tube 1
639034300 1/2” NPT Nipple 1
739034600 1/2” Steel Tubing 1
839034700 1/2” Pipe to Steel Tubing 2
939039000 45° Fitting, 34” Male, 1/2” Fem. 1
10 390406SC Auto-Return Valve 1
11 401413PB Beam 1
12 40141800 Wedge 1
13 07073100 Cylinder Pin 1
O/L- Obtain locally. Common fasteners available through hardware
and farm stores.
TONGUE ASSEMBLYBREAKDOWN
O/L- Obtain locally. Common fasteners available through
hardware and farm stores.
ITEM NO. PART NO. DESCRIPTION QTY
1O/L M10 x 1.5 Nylock Nut 2
2O/L M10 x 1.5 x 100mm GR5 Hex Bolt 1
3O/L M10 x 1.5 x 120mm GR5 Hex Bolt 1
4O/L M10 Flat Washer 5
5401273A0 Tongue 1
640034600 Hitch BallAssembly 1
7400323A0 Chain 2
840127400 Ground Stand Assembly 1
99114-1 Retaining Ring 1
10 9132-1 Spacer Washer 1
Page 15

ASSEMBLYINSTRUCTIONS LOG34
NOTE: This log splitter was partially assembled at the factory. Refer to the drawings and parts list should it become
necessary to disassemble the unit for repair or replacement of parts
ITEM NO. PART NO. DECSRIPTION QTY.
1401610PB Beam Assembly 1
240127500 Beam Lock Assembly 1
3401609PB Tank Assembly 1
4400312BO Tire and Wheel Assembly 2
540127200 Tongue Assembly 1
640142200 Fender 2
Page 16

STEP 1: Remove all the components from the shipping container.Inspect each piece for shipping damage. If any part is
damaged, contact your dealer or delivering carrier.
STEP 2: Attach the two wheels (1) to the tank assembly wheel spindles using the 3/4” light flat washers(2) ,3/4” NF
slotted nuts (3), 1/8” x 1-1/2” cotter pins (4) and the hub caps (5). These items are in the hardware package.
Tighten the slotted nuts and make sure the wheels rotate freely.
STEP 3: Attach the tongue assembly (5) to the tank assembly (1) using two 1/2” NC x 4-1/2” hex cap bolts (2), two 1/2” lock
washers (3) and two 1/2” hex nuts (4). Tighten.
ITEM NO. PART NO. DESCRIPTION QTY.
1400312B0 Tire and Wheel 2
2O/L 3/4” Light Flat Washer 2
317012000 3/4” Slotted Nut 2
4O/L 1/8” x 1-1/2” Cotter Pin 2
540033200 Hub Cap 2
O/L- Obtain locally. Common fasteners available through hardware
and farm stores.
Page 17
ITEM NO. PART NO. DESCRIPTION QTY.
1401609PB TankAssembly 1
2O/L 1/2” NC x 4-1/2 Hex Bolt 2
3O/L 1/2” Lock Washer 2
4O/L 1/2” NC Hex Nut 2
540127200 Tongue Assembly 1
O/L- Obtain locally. Common fasteners available through
hardware and farm stores.

STEP 4: Stand the beam (1) up on end. Two people may be needed for this step to ensure safety. Make sure that the beam
is stable and on a level surface.Remove the pivot pin (3) and clip pin (2) from the tank assembly.Roll the tongue/
tank assembly into position between the two tabs on the beam (1). Slide the pivot pin (3) through the aligned holes
and lock in place with the clip pin (2).
STEP 5: Connect the end of the 1/2” ID x 38” hydraulic pressure hose (1) coming from the fitting on the pump to the fitting
on the valve . See illustrations below.
STEP 6: Slide one hose clamp (3) on the end of the 3/4” x 56” hydraulic return hose (2 ) that comes from the fitting on the
filter . Then connect the hose to the fitting on the valve . See illustrations below.
ITEM NO. PART NO. DESCRIPTION QTY.
1401413PB Beam 1
2O/L 1/2”-3/4” R Clip Pin 1
3071022WC Pivot Pin 1
Area of
Detail
Page 18
ITEM NO. PART NO. DESCRPTION QTY.
139027500 1/2” X 38” Pressure Hose 1
239027400 3/4” x 56” Return Hose 1
339031600 Worm Gear Clamp 3
DETAILA
SCALE 1:3