Prime KC King 300 User manual
Prime Pellet Grill - KC King 300
Item#: 81222
1. Please read this entire manual before
installation and use of this pellet fuel-
burning appliance. Failure to follow these
instructions could result in property
damage, bodily injury, or even death.
about restrictions and installation
inspection requirements in your area.
3. Save these instructions for future
reference.
For Outdoor Use Only
Keep a copy of your proof of
which will be needed if you
need to contact us about
warranty coverage.
Purchase Date:
This product can expose you to chemicals including
Lead, Chromium (hexavalent compounds), Di(2-
ethylhexyl) phthalate (DEHP) and Diisononyl
phthalate (DINP), which are known to the State of
California to cause cancer and birth defects or other
reproductive harm. For more information, go to
www.P65Warnings.ca.gov.
12032019
Questions, problems, missing parts?
Before returning to your retailer, our exceptional customer service is available.
Call toll-free
-7877 9 a.m. – 9 p.m., EST
Email [email protected]
Live chat primepelletgrills 9 a.m. - 4 p.m., EST, Monday - Friday
Ignite, Inspire, Indulge
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com TABLE OF CONTENTS | 2
Please read and understand this entire manual before
attempting to assemble, operate or install this appliance.
If you have any questions regarding the product,
please contact Customer Service.
Safety precautions are essential when any mechanical or
wood pellet fueled equipment is involved. Always heed
these precautions, as they are essential when using any
mechanical or wood pellet fueled equipment. Contact
installation inspection requirements in your area.
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com COMPONENTS | 3
2
1
4
3
5
6
7
8
9
q
w
e
e
1
2
3
4
5
6
7
8
9
q
w
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com HARDWARE | 4
A
G
B
H
C
I
D
J
E
F
NOTE: It is best to use TWO people to
assemble this appliance.
(Not included)
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com SAFETY INFORMATION | 5
• Keep solid combustibles, such as building
materials, paper, or cardboard a safe distance
away from the grill as recommended by the
instructions.
• Provide adequate clearances around air
openings into the combustion chamber.
• Never use the grill in spaces which do or may
contain volatile or airborne combustibles,
or products such as gasoline, solvents, paint
thinner, dust particles, or unknown chemicals.
• During operation, this appliance can be a
source of ignition. Keep grill area clear and
free from combustible materials, gasoline,
paint thinner, cleaning solvents and other
grill in areas with high dust content. When
operating this grill, maintain a minimum
distance of 30.48 cm./12 in. from the grill to
combustibles.
• When operating this grill under overhead
combustibles, a minimum of 101.6 cm./40 in.
Is required.
• Only use this grill outside on a
noncombustible surface and away from all
combustible materials.
• Never use gasoline, gasoline-type lantern fuel,
all such substances far away from this grill.
WARNING indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury.
• Installation and repair should be done by
be inspected before use and annually by
cleaning may be required as necessary.
• This grill is a combustion appliance. All
combustion appliances produce Carbon
Monoxide (CO) during the combustion
process. This product is designed to produce
extremely minute, non-hazardous amounts
of CO if used and maintained in accordance
with all warnings and instructions.
• Carbon Monoxide (CO) poisoning produces
dizziness, fatigue, and possible death. You
can’t see and you can’t smell it. It is an
invisible killer. If these symptoms are present
during operation of this product, get fresh air
immediately!
• For outdoor use only. Never use inside house,
building, or other unventilated or enclosed
areas.
• This grill consumes air (Oxygen). Do not use
in unventilated or enclosed areas to avoid
endangering your life.
• Alcohol consumption and drug use increase
the effects of Carbon Monoxide poisoning.
• Carbon Monoxide is especially toxic to mother
and child during pregnancy, infants, the
elderly, smokers, and people with blood or
circulatory system problems, such as anemia
or heart disease.
• Never leave grill unattended when hot or in
use.
• Keep out of reach of children. Children should
be supervised while in the vicinity of the grill.
• Never move the grill while it is operating.
• The grill must cool completely before being
moved, transported, or cleaned.
• Alert children and adults to the hazards of
high surface temperatures. Stay away from
these surfaces to avoid burning skin or
igniting clothing.
• By-products of the combustion fuel used
by this product contain chemicals known to
the State of California to cause cancer, birth
defects, or other reproductive harm.
• Make sure grill is plugged in to an appropriate
3-prong outlet.
• An electrical supply with a GFCI protection
is required. In order to protect against shock
hazard, locate a grounded 3-prong receptacle
in reach of the 1.8 m./6 ft. power cord. When
installing the receptacle, follow the National
Code and local codes and ordinances.
• This grill must only be assembled and
operated in accordance with this instruction
manual and its warnings.
• Never use heating fuel pellets in this grill due
to potential hazardous contaminants and
additives that may be present.
Prime Pellet Grills brand wood pellets.
• Wood pellets must be stored in a dry location
and away from heat-producing appliances
and other fuel containers.
• Keep this grill clean. Please refer to the
cleaning instructions in this instruction
manual.
with this grill.
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com ASSEMBLY | 6
Before beginning assembly, be sure to empty contents of carton and make sure all parts are present. READ ALL INSTRUCTIONS BEFORE INSTALLING AND USING THE APPLIANCE.
Place all parts on a nonabrasive, level surface for assembly.
Estimated Assembly Time: 60 Minutes | DO NOT over tighten hardware!
On a protected, level surface on the ground, turn the 1upside-down.
Attach the 3inside the corners of the skirt of the , as
shown: Align the bolt eyelets in each leg with the eyelets in corners of the skirt
panels of the . Insert Cinto the front skirt panel of the grill and through
the leg, fastening with H, I, and E. Repeat with
the same hardware on the back leg. Insert 2 Dinto the two eyelets in the side
skirt panel on either side of the hopper, and through the . Secure with
the same combination of fastening hardware H/I/E.
Attach the 4to the opposite end of the , as shown: First
make sure that the wheels are positioned on the sides of the legs AWAY FROM
the grill. Insert Cinto the front skirt panel of the grill and through the leg,
fastening with H, I, and E. Repeat with the
same hardware on the back leg. Insert 2 Dinto the two eyelets in the bottom
edge of the side skirt panel, and through the . Secure with the same
combination of fastening hardware H/I/E.
Hardware Used:
CBolt (5/16x55) x 4 DBolt (5/16x75) x 4
EFlange Nut (5/16) x 8 HWasher (5/16) x 8
ISpring Washer (5/16) x 8
3
3
4
C
C
C
C
D
1
HIE 4
1
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com ASSEMBLY | 7
Install the 9: Open the grill door. Align the q
with the open end of the , then align both with the eyelets on
either side of the exhaust hole on the body of the grill. Insert 2 Ainto the
eyelets and fasten them on the inside of the grill using a Gand
Fon each .
Fully tighten Chimney hardware.
Hardware Used:
ABolt (1/4x20) x 2
FFlange Nut (1/4) x 2
GWasher (1/4) x 2
3
Carefully turn the grill back upright. Install the 2by sliding the Fire
Pot into the large opening on the side of the 1. (NOTE: both parts have a
wire extending from the facing sides. Pull these up and out of the way until the
is fully installed. Fasten the to the using B/ J/
Gas shown in the illustration: place a , then a on
each . From inside the , insert each through 1 of the 4 eyelets drilled
through the side of the Grill Body and into the . Once all 4 sets of hardware are
placed, fully tighten all using the included .
After installing , connect the two wires together as shown in the circled
portion of the diagram at right, then tuck the wires into the space between the Hopper
and the Grill Body.
Hardware Used:
BBolt (1/4x20mm) x 4
GWasher (1/4) x 4
JSpring Washer (1/4) x 4 2
2
GJB
F G
q
A
9
GJB
2
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com ASSEMBLY | 8
Attach the e: Loosen and remove the two and from either end
of the . Place the on the , and from the inside of the door, insert
one through each eyelet in the grill door into either end of the . Fully tighten both
using the included .
Hardware Used (pre-installed in handle):
Bolt (1/4x20) x 2
Washer (1/4) x 2
4
Attach the w: Loosen and remove the two and from
either end of the . Insert the threads on the into the eyelets below the
. From inside the , slide a onto each set of threads, then secure each
end with a . Fully tighten both using the .
Hardware Used (pre-installed on Haul Handle):
Flange Nut (10-32) x 2
Spring Washer (10-32) x 2
5
e
w
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com ASSEMBLY | 9
Position the 6over the in
the bottom of the grilling chamber. Ensure that it
is seated securely to avoid shifting.
Hang the 5below the grease
drain hole on the back of the.
Place the interior components: First insert the 7, ensuring that the
drain tube is inserted into the drain hole in the rear of the grilling chamber. Then,
add the 8.
You’re almost there! Follow the instructions for Initial Firing and Seasoning your Prime
Pellet Grill on Pages 10-14.
6 7
8
K
D
A
J
8
7
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com OPERATION | 10
Take out the interior components including cooking grates, grease
Turn the switch to OFF (O) and plug the power cord into a
grounded household outlet.
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com GRILL OPERATION | 11
FIRST START-UP
INITIAL FIRING INSTRUCTIONS
Remove the porcelain-coated grill
grate, grease drain pan, and both
the inside of the grill.
With the switch in the OFF ( O)
position, plug the power cord into an
appropriate grounded electrical outlet.
ellets.
auger tube to be “charged” with pellets.
1 2
INITIAL FIRING INSTRUCTIONS
375Smoke
Shut Down
Cycle High
Power
OFF
ON
Smoke
Shut D
Cy
Po
Remove the porcelain-coated grill
grate, grease drain pan, and both
the inside of the grill.
auger tube to be “charged” with pellets.
1
1 Take out the interior components including cooking grates, grease
2Turn the switch to OFF (O) and plug the power cord into a
grounded household outlet.
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com
Check the pellet hopper and the auger for foreign objects, which
can jam the auger. Turn the switch to ON (I) and rotate the dial to
IGNITE. Verify that the auger is rotating inside the hopper.
begin to redden as it heats up. CAUTION! Do not touch the heating rod.
OPERATION | 11
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com
Check the pellet hopper and the auger for foreign objects, which
can jam the auger. Turn the switch to ON (I) and rotate the dial to
IGNITE. Verify that the auger is rotating inside the hopper.
begin to redden as it heats up. CAUTION! Do not touch the heating rod.
OPERATION | 12
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com OPERATION | 12
Pour Prime Pellet Grill Hardwood Pellets into the hopper and set
the temperature dial to MAX.
temperature to BURN OFF. Wait a moment, then with pellets still in the
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com OPERATION | 13
Pour Prime Pellet Grill Hardwood Pellets into the hopper and set
the temperature dial to HIGH.
temperature to BURN OFF. Wait a moment, then with pellets still in the
F
225
180
325
275
375Smoke
Shut Down
Cycle High
Power
OFF
ON
CALL
SERVICE
Fill t he hopper with Traeger H ardwood
Pellets and turn thetemperature dial
to HIGH .
When the pellets begin to fall into the
SHUT DOWN CYCLE to reset the hot
turn the temperatu re dial back to
SMOKE.
5 6
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com OPERATION | 13
Pour Prime Pellet Grill Hardwood Pellets into the hopper and set
the temperature dial to HIGH.
temperature to BURN OFF. Wait a moment, then with pellets still in the
F
225
180
325
275
375Smoke
Shut Down
Cycle High
Power
OFF
ON
CALL
SERVICE
Fill t he hopper with Traeger H ar dwood
Pellets and turn thetemperature dial
to HIGH .
When the pellets begin to fall into the
SHUT DOWN CYCLE to reset the hot
turn the temperatu re dial back to
SMOKE.
5 6
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com OPERATION | 13
dial to BURN OFF and turn the switch to OFF (O). Let the grill cool.
The interior components can now be placed in their proper
the Upper Cooking Grate.
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com OPERATION | 14
Recommendation:
g
foil. Be su
tight against the bottom of the g
pan. Replace foil after each cook to
for mo
SHU T DOWN C YCLE and switch to
OFF. Let the grill cool down.
7
225
180
325
375Smoke
Shut Down
Cycle High
Power
OFF
225
180
325
375Smoke
Shut Down
Cycle High
Power
OFF
225
180
325
375Smoke
Shut Down
Cycle High
Power
OFF
ON
Fill t he hopper wit h Traeger H ardwood
Pellets and turn the temperature dial
to HIGH .
When the pellets begin to fall into the
SHUT DOWN CYCLE to reset the hot
turn the temperatu re dial back to
SMOKE.
5 6
F
225
180
325
275
375Smoke
Shut Down
Cycle High
Temperature
Power
OFF
ON
Now you’re ready to place the
drain pan, and po rcelain-coated grill
grates back into the grill.
SHU T DOWN C YCLE and switch to
OFF. Let the grill cool down.
7 8
dial to BURN OFF and turn the switch to OFF (O). Let the grill cool.
The interior components can now be placed in their proper
the Upper Cooking Grate.
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com OPERATION | 14
Leaving the grill door up, turn the switch to ON (I) and the dial to
IGNITE. Within minutes, pellets will begin to ignite and give off light
gray smoke. Once smoke rises, close the door and turn the dial to your
following step.
to properly season it: after following the steps for Initial Firing,
turn the temperature dial to MAX and let it run for 45 minutes with the
door closed.
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com OPERATION | 15
225
180
325
275
375Smoke
Shut Down
Cycle High
Power
OFF
ON
With the door open, turn the switch
ON ( I) and the temperature dial to
SMOKE. In about 2 minutes, the pellets
will ignite and whitish-gray smoke will
come out of the grill. After the pellets
have ignited, close the door and turn
the temperature dial to any cooking
setting desired.
Before
time, it will need to be seasoned.
Turn the temperature dial to HIGH
and let run for 45 minutes with the
door closed.
910
INITIAL FIRING INSTRUCTIONS (cont.)
WARNING!
·Start the grill on SMOKE setting with the door open. Once the pellets a
the temperature dial to any desired cooking temperature.
·When operating this grill, maintain a minimum clearance of 30.48 cm / 12 in f
·
in the grill.
·
more details.
225
180
Smoke
Shut D
Cy
P
With the door open, turn the switch
ON ( I) and the temperature dial to
SMOKE. In about 2 minutes, the pellets
will ignite and whitish-gray smoke will
come out of the grill. After the pellets
have ignited, close the door and turn
the temperature dial to any cooking
setting desired.
910
INITIAL FIRING INSTRUCTIONS
CONTROLLER SHUT D
Leaving the grill door up, turn the switch to ON (I) and the dial to
IGNITE. Within minutes, pellets will begin to ignite and give off light
gray smoke. Once smoke rises, close the door and turn the dial to your
following step.
to properly season it: after following the steps for Initial Firing,
turn the temperature dial to HIGH and let it run for 45 minutes with the
door closed.
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com OPERATION | 15
225
180
325
275
375Smoke
Shut Down
Cycle High
Power
OFF
ON
With the door open, turn the switch
ON ( I) and the temperature dial to
SMOKE. In about 2 minutes, the pellets
will ignite and whitish-gray smoke will
come out of the grill. After the pellets
have ignited, close the door and turn
the temperature dial to any cooking
setting desired.
Before
time, it will need to be seasoned.
Turn the temperature dial to HIGH
and let run for 45 minutes with the
door closed.
910
INITIAL FIRING INSTRUCTIONS (cont.)
WARNING!
·Start the grill on SMOKE setting with the door open. Once the pellets a
the temperature dial to any desired cooking temperature.
·When operating this grill, maintain a minimum clearance of 30.48 cm / 12 in f
·
in the grill.
·
more details.
225
180
Smoke
Shut D
Cy
P
With the door open, turn the switch
ON ( I) and the temperature dial to
SMOKE. In about 2 minutes, the pellets
will ignite and whitish-gray smoke will
come out of the grill. After the pellets
have ignited, close the door and turn
the temperature dial to any cooking
setting desired.
910
INITIAL FIRING INSTRUCTIONS
CONTROLLER SHUT D
Leaving the grill door up, turn the switch to ON (I) and the dial to
IGNITE. Within minutes, pellets will begin to ignite and give off light
gray smoke. Once smoke rises, close the door and turn the dial to your
following step.
to properly season it: after following the steps for Initial Firing,
turn the temperature dial to HIGH and let it run for 45 minutes with the
door closed.
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com OPERATION | 15
Always start the grill with the door open and the dial set to IGNITE. After
pellets ignite and produce smoke, close the lid and adjust the dial to your
preferred cooking temperature.
• Whenever the grill is in use or cooling down after grilling, you must
maintain a minimum of 30.48 cm / 12 in between the grill and any
combustibles, including stored pellets.
Prime Pellet Grill Hardwood Pellets. NEVER use heating fuel pellets to
cook food.
• Keep the grease drain pan and the interior of your grill clean to reduce
This grill features an automatic shut down cycle. When you’re done cooking,
while running the circulation fan. In ten minutes, the grill will shut down and the
fan will stop.
Your Prime Pellet Grill has two emergency shutoff safety features.
If the RTD temperature sensor detects sustained temperatures below 125°F, the control will trigger an alarm state and the display will show “LEr.” Power will be cut
to the internal components of the grill (auger and heating rod) until the main power switch is turned OFF (O).
If the RTD temperature sensor detects an internal temperature exceeding 550°F, the control will trigger an alarm state and the display will show “HEr.” Power will
be cut to the internal components of the grill (auger and heating rod) until the main power switch is turned OFF (O).
and remedy the issue.
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com TITLE | 16
If the temperature reading has not reached the set temperature
after ten minutes of preheating, turn the dial to BURN OFF. Now re-set to
your preferred temperature.
If the grill still fails to reach set temperature, consult Troubleshooting
(pages 24-25) for more information on grilling issues.
Open the door and turn the grill power to ON (I). Set the
within about two minutes, creating light gray smoke. Once you see
smoke, close the door and turn the dial to your preferred cooking
temperature.
Prior to adding food, let the grill preheat for 10 minutes with the
door closed.
OPERATION | 16Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com OPERATION | 15
225
180
325
275
375Smoke
Shut Down
Cycle High
Power
OFF
ON
With the door open, turn the switch
ON ( I) and the temperature dial to
SMOKE. In about 2 minutes, the pellets
will ignite and whitish-gray smoke will
come out of the grill. After the pellets
have ignited, close the door and turn
the temperature dial to any cooking
setting desired.
Before
time, it will need to be seasoned.
Turn the temperature dial to HIGH
and let run for 45 minutes with the
door closed.
910
INITIAL FIRING INSTRUCTIONS (cont.)
WARNING!
·Start the grill on SMOKE setting with the door open. Once the pellets a
the temperature dial to any desired cooking temperature.
·When operating this grill, maintain a minimum clearance of 30.48 cm / 12 in f
·
in the grill.
·
more details.
225
180
Smoke
Shut D
Cy
P
With the door open, turn the switch
ON ( I) and the temperature dial to
SMOKE. In about 2 minutes, the pellets
will ignite and whitish-gray smoke will
come out of the grill. After the pellets
have ignited, close the door and turn
the temperature dial to any cooking
setting desired.
910
INITIAL FIRING INSTRUCTIONS
CONTROLLER SHUT D
Leaving the grill door up, turn the switch to ON (I) and the dial to
IGNITE. Within minutes, pellets will begin to ignite and give off light
gray smoke. Once smoke rises, close the door and turn the dial to your
following step.
to properly season it: after following the steps for Initial Firing,
turn the temperature dial to HIGH and let it run for 45 minutes with the
door closed.
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com OPERATION | 15
225
180
325
275
375Smoke
Shut Down
Cycle High
Power
OFF
ON
With the door open, turn the switch
ON ( I) and the temperature dial to
SMOKE. In about 2 minutes, the pellets
will ignite and whitish-gray smoke will
come out of the grill. After the pellets
have ignited, close the door and turn
the temperature dial to any cooking
setting desired.
Before
time, it will need to be seasoned.
Turn the temperature dial to HIGH
and let run for 45 minutes with the
door closed.
910
INITIAL FIRING INSTRUCTIONS (cont.)
WARNING!
·Start the grill on SMOKE setting with the door open. Once the pellets a
the temperature dial to any desired cooking temperature.
·When operating this grill, maintain a minimum clearance of 30.48 cm / 12 in f
·
in the grill.
·
more details.
225
180
Smoke
Shut D
Cy
P
With the door open, turn the switch
ON ( I) and the temperature dial to
SMOKE. In about 2 minutes, the pellets
will ignite and whitish-gray smoke will
come out of the grill. After the pellets
have ignited, close the door and turn
the temperature dial to any cooking
setting desired.
910
INITIAL FIRING INSTRUCTIONS
CONTROLLER SHUT D
Leaving the grill door up, turn the switch to ON (I) and the dial to
IGNITE. Within minutes, pellets will begin to ignite and give off light
gray smoke. Once smoke rises, close the door and turn the dial to your
following step.
to properly season it: after following the steps for Initial Firing,
turn the temperature dial to HIGH and let it run for 45 minutes with the
door closed.
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com
If the grill fails to light or goes out unexpectedly, turn the switch
OFF (O) and unplug the grill from power. Allow the grill to cool
completely.
After the grill is cool, remove any food and the grates, drain pan,
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com
If the grill fails to light or goes out unexpectedly, turn the switch
OFF (O) and unplug the grill from power. Allow the grill to cool
completely.
After the grill is cool, remove any food and the grates, drain pan,
375Smoke
Shut Down
Cycle High
Power
OFF
ON
DANGER! If the grill failed to light or
(O) and disconnect the power cord.
If the grill is still hot, allow it to cool
thoroughly.
Open the door and remove all food,
the porcelain-coated grill grates, the
grease drain pan, and the upper and
WARNING!
1 2
REIGNITING YOUR GRILL
DANGER! If the grill failed to light or
(O) and disconnect the power cord.
If the grill is still hot, allow it to cool
thoroughly.
WARNING!
1
REIGNITING YOUR GRILL
OPERATION | 18
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com
If the grill fails to light or goes out unexpectedly, turn the switch
OFF (O) and unplug the grill from power. Allow the grill to cool
completely.
After the grill is cool, remove any food and the grates, drain pan,
375Smoke
Shut Down
Cycle High
Power
OFF
ON
DANGER! If the grill failed to light or
(O) and disconnect the power cord.
If the grill is still hot, allow it to cool
thoroughly.
Open the door and remove all food,
the porcelain-coated grill grates, the
grease drain pan, and the upper and
WARNING!
1 2
REIGNITING YOUR GRILL
DANGER! If the grill failed to light or
(O) and disconnect the power cord.
If the grill is still hot, allow it to cool
thoroughly.
WARNING!
1
REIGNITING YOUR GRILL
OPERATION | 18
OPERATION | 17
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com
WARNING! You must remove all unburned pellets and ash
information on ash removal.
Plug the grill back in to a grounded power outlet. Turn the grill
back to ON and the dial to IGNITE. The auger should push pellets
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com
WARNING! Remove all unburned
pellets and ash from inside and
for proper handling and disposal of
ash on page 19.)
Plug power cord into an appropriate
grounded electrical outlet and restart
the grill. Pellets should fall into the
to heat (it will start to turn red).
CAUTION! Do not touch the hot rod.
3 4
Power
ON
DANGER! If the grill failed to light or
(O) and disconnect the power cord.
If the grill is still hot, allow it to cool
thoroughly.
Open the door and remove all food,
the porcelain-coated grill grates, the
grease drain pan, and the upper and
1 2
20
WARNING! Remove all unburned
pellets and ash from inside and
for proper handling and disposal of
ash on page 19.)
3
WARNING! You must remove all unburned pellets and ash
information on ash removal.
Plug the grill back in to a grounded power outlet. Turn the grill
back to ON and the dial to IGNITE. The auger should push pellets
OPERATION | 19
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com
WARNING! Remove all unburned
pellets and ash from inside and
for proper handling and disposal of
ash on page 19.)
Plug power cord into an appropriate
grounded electrical outlet and restart
the grill. Pellets should fall into the
to heat (it will start to turn red).
CAUTION! Do not touch the hot rod.
3 4
Power
ON
DANGER! If the grill failed to light or
(O) and disconnect the power cord.
If the grill is still hot, allow it to cool
thoroughly.
Open the door and remove all food,
the porcelain-coated grill grates, the
grease drain pan, and the upper and
1 2
20
WARNING! Remove all unburned
pellets and ash from inside and
for proper handling and disposal of
ash on page 19.)
3
WARNING! You must remove all unburned pellets and ash
information on ash removal.
Plug the grill back in to a grounded power outlet. Turn the grill
back to ON and the dial to IGNITE. The auger should push pellets
OPERATION | 19
OPERATION | 18
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com OPERATION | 13
Pour Prime Pellet Grill Hardwood Pellets into the hopper and set
the temperature dial to HIGH.
temperature to BURN OFF. Wait a moment, then with pellets still in the
F
225
180
325
275
375Smoke
Shut Down
Cycle High
Power
OFF
ON
CALL
SERVICE
Fill t he hopper with Traeger H ar dwood
Pellets and turn the temperature dial
to HIGH .
When the pellets begin to fall into the
SHUT DOWN CYCLE to reset the hot
turn the temperatu re dial back to
SMOKE.
5 6
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com
to OFF (O) and let the grill cool. After the grill is cool you can
Leaving the grill door open, turn the switch ON (I) and the dial
to IGNITE. The pellets will ignite and light gray smoke will rise.
After seeing smoke, close the door and adjust the dial to your desired
cooking temperature.
OPERATION | 19
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com
O).
Let the grill cool down. Now you’re
ready to place the upper and lower
porcelain-coated grill grates back into
the grill.
NOTE: If the procedure is not successful, see “FREQUENTLY ASKED QUESTIONS” on page 22 for
troubleshooting tips or contact Traeger's VIP-365 Customer Service (see page 26) to help diagnos
problem.
5
375
Shut Down
Cycle High
ower
OFF
ON
With the door open, turn the switch
ON ( I) and the temperature dial to
SMOKE. In about 2 minutes, the pellets
will ignite and whitish-gray smoke will
come out of the grill. After the pellets
have ignited, close the door and turn
the temperature dial to any cooking
setting desired.
O).
Let the grill cool down. Now you’re
ready to place the upper and lower
porcelain-coated grill grates back into
the grill.
5 6
to OFF (O) and let the grill cool. After the grill is cool you can
Leaving the grill door open, turn the switch ON (I) and the dial
to IGNITE. The pellets will ignite and light gray smoke will rise.
After seeing smoke, close the door and adjust the dial to your desired
cooking temperature.
OPERATION | 20
225
180
325
275
Shut Do
Cycle
Power
ON
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com
O).
Let the grill cool down. Now you’re
ready to place the upper and lower
porcelain-coated grill grates back into
the grill.
NOTE: If the procedure is not successful, see “FREQUENTLY ASKED QUESTIONS” on page 22 for
troubleshooting tips or contact Traeger's VIP-365 Customer Service (see page 26) to help diagnos
problem.
5
375
Shut Down
Cycle High
ower
OFF
ON
With the door open, turn the switch
ON ( I) and the temperature dial to
SMOKE. In about 2 minutes, the pellets
will ignite and whitish-gray smoke will
come out of the grill. After the pellets
have ignited, close the door and turn
the temperature dial to any cooking
setting desired.
O).
Let the grill cool down. Now you’re
ready to place the upper and lower
porcelain-coated grill grates back into
the grill.
5 6
to OFF (O) and let the grill cool. After the grill is cool you can
Leaving the grill door open, turn the switch ON (I) and the dial
to IGNITE. The pellets will ignite and light gray smoke will rise.
After seeing smoke, close the door and adjust the dial to your desired
cooking temperature.
OPERATION | 20
225
180
325
275
Shut Do
Cycle
Power
ON
Contact us for assistance: (866) 985-7877 | www.primepelletgrills.com
1. During grilling, adjust the dial at any time to grill hotter or cooler, or to adjust smokiness. The HIGH setting is for grilling, while the IGNITE setting is for smoking or adding
2. This Prime Pellet Grill is a cooking appliance fueled by food-grade hardwood pellets. A heating element inside the grill chamber serves as the ignition point to start the
5. Always account for ambient temperatures when estimating grilling times. Your grill will reach cooking temperatures quickly on a hot sunny day, and more slowly on cold,
wet, or windy days.
6. Controller Function: After dialing in cooking temperature, the auger will operate until the desired temperature is reached. To maintain cooking temperature, the digital
controller will activate the auger as necessary to maintain temperature.
has cooled completely, remove the grate and any foil used to protect the grease drain pan. Clean the grate, pan, drain, and drain tube of any accumulation of grease. Line
the pan with new foil, then put the drain pan and the cooking grate back in position, restart the grill, and resume cooking.
OPERATION | 20
This manual suits for next models
1
Table of contents
