Pro Breeze PB-AC05 User manual

Instruction manual
Mode d’emploi
Manuale di istruzioni
Bedienungsanleitung
Manual de instrucciones
Model PB-AC05
12000 BTU Portable Air Conditioner

02 | English
Portable Air Conditioner
Thank you for choosing to purchase a product from Pro Breeze. Please read the entire
manual carefully prior to rst use and keep in a safe place for future reference.
Safety Warning
• Use the appliance only as described
in this instruction manual.
• Check that the voltage of the main
circuit corresponds with the rating of
the appliance before operating.
• This appliance is suitable for indoor
use only.
• This appliance is not a toy. Never
leave unattended around children or
pets.
• This appliance can be used by
children aged from eight years above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
• Children shall not play with the
appliance.
• Cleaning and user maintenance shall
not be made by children without
supervision.
• Keep the appliance and all parts out
of the reach of children.
• This appliance is intended for
domestic use only. It should not be
used for commercial purposes.
Contents Pg
Safety Warning 02
Specic Information Regarding R290 Refrigerant Gas 04
Caution | Specications 05
Parts 06
Control Panel 07
Installation 08
Controls 10
Emptying the Water Tank 14
Connecting the Water Hose for Continuous Drainage 15
Cleaning | Storage | Safety Features 16-17
Disposal 18
Helpful Information 19

English | 03
• Place the appliance on a at and
dry surface. Keep it at least 50cm
away from surrounding walls and/or
objects.
• When moving the appliance ensure it
is kept in an upright position.
• When adjusting the louvres do so
gently so as not to cause damage.
• Ensure the power cord plug is
properly inserted into the power
socket before operating.
• Where there is the need to install a
continuous drainage hose ensure the
connection of the drainage hose is in
good condition without exure.
• Do not cover the power cord.
• Do not insert ngers or objects into
the air inlet or air outlet. Be sure
to keep the air inlet and air outlet
unblocked.
• Do not operate the appliance with
wet hands.
• Do not leave the appliance
unattended whilst connected to the
power supply.
• Do not pull the power cord to stop
the appliance.
• Do not unplug the appliance until it
has been switched off.
• Do not modify the appliance or use
any accessories other than those
supplied.
• Do not place or use the appliance,
power cord, or any accessories in a
bathroom, wet, or damp place.
• Do not cover the appliance whilst in
use.
• Do not use pressurised containers
(e.g. aerosol cans) or other ammable
substances near the appliance.
• Do not use the appliance near petrol,
ammable gases, ovens, or other
heating sources.
• Do not allow water or other liquids
to enter into the appliance or
contaminate electrical parts.
• Do not attempt to repair or adjust
any electrical or mechanical elements
in the appliance. Doing so may be
unsafe and will void your warranty.
• Do not operate the appliance if
there are signs of damage to the
appliance, power cord, or any of the
accessories.
• Do not wipe or wash the appliance
with chemical solvents. Prior to
cleaning ensure the appliance is
turned off and unplugged from the
power supply.
• Avoid placing the power cord in
areas where it can become a tripping
hazard.
• Avoid using extension cables as they
may overheat and cause a re risk.
• Unplug the appliance and store in a
cool and dry place when not in use.
• Never place anything on top of the
appliance.

04 | English
Specific Information
Regarding R290
Refrigerant Gas
• The appliance must be installed, used
and stored in an area that is greater
than 13m2.
• This appliance contains 265g of R290
refrigerant gas.
• R290 is a refrigerant gas that
complies with the European directive
on the environment.
• Do not puncture any part of
refrigerant circuit.
• Be aware R290 refrigerant is
odourless and does not have the
odour normally associated with
natural gas and propane tanks.
• The appliance must be placed in an
area without any continuous sources
of ignition such as open ames, gas,
or electrical appliances in operation.
• Do not puncture and do not burn.
• If the appliance is installed, operated
or stored in a non-ventilated area, the
room must be designed to prevent
the accumulation of refrigerant leaks
resulting in a risk of re or explosion
due to ignition of the refrigerant
caused by electric heaters, stoves, or
other sources of ignition.
• The appliance must be stored in
such a way as to prevent mechanical
failure.
• Individuals who operate or work on
the refrigerant circuit must have the
appropriate certication issued by an
accredited organisation that ensures
competence in handling refrigerants
according to a specic evaluation
recognised by associations in the
industry.
• Maintenance and repairs that require
the assistance of other qualied
personnel must be performed under
the supervision of an individual
specied in the use of ammable
refrigerants.

English | 05
Caution
• Do not operate the appliance if the
room temperature is greater than 32°C
in cooling mode or lower than 5°C in
dehumidifying mode.
Specifications
• Size: 36cm x 43cm x 73cm
• Net Weight: 29.5kg
• Input Voltage: 220V-240V~
• Frequency: 50Hz
• Cooling Capacity: 12000 BTU/H
• Heating Capacity: 12700 BTU/H
• Refrigerant: R290 (265g)
• Energy Efciency Class For Cooling: A
• Energy Efciency Class For Heating: A+
• Rated Capacity For Cooling: 3520W
• Rated Capacity For Heating: 3300W
• Rated Input For Cooling: 1350W
• Rated Input For Heating: 1500W
• Rated Current For Cooling: 5.5A
• Rated Current For Heating: 6.0A
• EER For Cooling: 2.6
• EER For Heating: 2.6
• Moisture Removal: 1.1L/H
• Air Flow Volume: 480m3/H
• Applicable Area: 30m2
• Operating Temperature Range: 5-32°C
• Available Temperature Settings: 16-30°C
• Noise Level | High: 65dB
• Noise Level | Low: 56dB

06 | English
Parts
Front View
1. Control panel
2. Swinging louvre
3. Body
4. Wheels
Rear View
5. Body
6. Remote control
7. Remote control holder
8. Evaporator lter cover /
evaporative lter
9. Handle
10. Handle
11. Power cord tidy
12. Continuous drainage cap /
continuous water outlet
13. Radiating lter
14. Heat exhaust hose connector
15. Condenser lter
16. Wheels
17. Bottom drainage cap /
bottom water outlet
Accessories
18. Remote control
19. Circular heat exhaust hose connector
20. Heat exhaust hose
21. Heat exhaust hose short connector
22. Sliding window sealing board
assembly
23. Hinged window fabric sealing
assembly
24. Sealing velcro
25. Water hose
18
22
21
20
19
23
24
25
6510 7 8
3
9
11
12
13
14
4
16 17 15
1
2

English | 07
Control Panel
1. Buttons moving from left to right
• Power button
• Mode button
• Up button
• Down button
• Fan speed button
• Timer button
2. Indicator light symbols moving from
top to bottom and left to right
• Cooling mode indicator light
• Fan-only mode indicator light
• Dehumidifying mode indicator light
• Heating mode indicator light
• High fan speed indicator light
• Medium fan speed indicator light
• Low fan speed indicator light
• WiFi indicator light
• Timer indicator light
3. Digital display panel moving from top
to bottom
• Degrees celsius indicator light
• Degrees fahrenheit indicator light
Remote Control
1. Timer button
2. Swing button
3. Temperature unit change button
4. Up button
5. Fan speed button
6. Power button
7. Mode button
8. Down button
Note: Two AAA batteries included.
1
5
2
3
4
6
7
8

08 | English
Installation
Prior to and after installation adhere to
the below:
• When moving the appliance to the
chosen location ensure it is kept in an
upright position.
• Do not place or use the appliance,
power cord, or any accessories in a
bathroom, wet, or damp place.
• Place the appliance on a at and
dry surface. Keep it at least 50cm
away from surrounding walls and/or
objects.
• Leave the appliance in an upright
position for at least two hours prior
to first use.
Heat Exhaust Hose Installation
1. Insert the circular connector into the
heat exhaust hose connector.
2. Rotate the circular connector
counterclockwise to lock it into place.
Sliding Window Sealing Board Assembly
Installation
1. Insert panel B into panel A and adjust
to the length or height of the window.
2. Open window and place the sealing
board assembly into window.
3. Adjust to ensure an exact t and
secure with the provided screw.
4. Close window to lock everything into
place.
5. Attach the heat exhaust hose short
connector to the elliptical hole.
6. The sealing board assembly is now
ready for use.
Notes:
• If your window opening is smaller
than the minimum length of the
sealing board assembly trim to
desired length using a hacksaw.
• If your window opening is larger than
the maximum length of the sealing
board assembly use plywood or
similar to ll the gap.
Circular connector

English | 09
Hinged Window Sealing Fabric
Assembly Installation
1. Open window and clean frame and
casement surfaces of dust and
particles.
2. Stick the velcro tape around the
entire window frame. Never stick
to the window seal as doing so will
prohibit the window from closing fully.
3. Stick the velcro tape around the
entire window casement (inside or
outside). Check to ensure the window
can close fully.
4. Attach side A of the sealing fabric
assembly to the velcro on the window
frame working from the centre
outwards.
5. Close and open window to ensure no
fabric gets trapped.
6. Attach side B of the sealing fabric
assembly to the velcro on the window
casement working from the centre
outwards.
7. Open the window slightly and
insert the heat exhaust hose short
connector into the sealing fabric
assembly securing with the zippers
around its lip.
8. The sealing fabric assembly is now
ready for use.
Notes:
• Do not bend the heat exhaust hose in
excess of 45 degrees. It should be as
short and as straight as possible to
ensure efcient air ow.
• Do not overstretch the heat
exhaust hose as this may affect the
appliances efciency.
Frame
Side A
Side B
Casement
7
4 & 6
2 &3
Hinged window sealing fabric zip

10 | English
Controls
Control Panel
Power Button
Turn the appliance on and off.
Mode Button
Select between cooling, dehumidifying,
fan-only, and heating modes.
• Cooling Mode - Perfect for cooling
a room in hot weather. Use the up
and down buttons when in cooling
mode to set the desired temperature
between 16-30°C. The appliance
will cool the room if the room
temperature goes above the set
temperature. If the room temperature
goes below the set temperature the
appliance will stop cooling the room
and the fan will remain operating at
the set fan speed.
Note: The heat exhaust hose must
be connected to allow the hot and
humid air to be discharged outside.
• Fan-Only Mode - The appliance
operates at the set fan speed. Room
temperature is displayed on the
digital display panel.
Note: The heat exhaust hose does
not have to be connected to the
appliance.
• Dehumidifying Mode - Ideal for
reducing room humidity in humid
and damp times of year. The
appliance will dehumidify the room
if the room temperature is greater
than or equal to 15°C and the fan
operates at the low fan speed. If the
room temperature decreases to less
than 15°C the appliance will stop
dehumidifying the room and the fan
operates at the low fan speed. Room
temperature is displayed on the
digital display panel.
Note: The heat exhaust hose must
be connected to allow the hot and
humid air to be discharged outside.
• Heating Mode - Perfect for heating
a room in cold weather. Use the up
and down buttons when in heating
mode to set the desired temperature
between 16-30°C. The appliance
will heat the room if the room
temperature goes below the set
temperature. If the room temperature
goes above the set temperature the
appliance will stop heating the room
and the fan will remain operating at
the set fan speed.
Note: The heat exhaust hose must
be connected to allow the cold and
humid air to be discharged outside.
Note: Temperature can only be set when in
cooling mode or heating mode.
Fan Speed Button
Select between high, medium, and low
fan speeds.
Note: Option not available in
dehumidifying mode.

English | 11
Timer Button
Set a turn-on or turn-off timer between
1-24 hours.
Setting a turn-on timer:
1. Ensure the appliance is plugged in
and the power socket turned on.
2. Press the timer button to activate the
timer function.
3. Press the up and down buttons to
set the desired time (1-24 hours) until
turn-on.
4. The time digits will blink ve times
to conrm a timer has been set and
the timer indicator light will remain
illuminated.
5. Select the desired settings prior to
turn-on.
6. To check the remaining time till turn-
on press the timer button.
7. To cancel the turn-on timer set the
time until turn-on to 0 hours or turn
the appliance on and off.
Note: If no desired settings are selected
the appliance will turn on in the previously
set settings.
Setting a turn-off timer:
1. Ensure the appliance is plugged in
and the power socket turned on.
2. Press the power button to turn the
appliance on.
3. Press the timer button to activate the
timer function.
4. Press the up and down buttons to
set the desired time (1-24 hours) until
turn-off.
5. The time digits will blink ve times
to conrm a timer has been set and
the timer indicator light will remain
illuminated.
6. Select the desired settings prior to
turn-off.
7. To check the remaining time till turn-
off press the timer button.
8. To cancel the turn-off timer set the
time until turn-off to 0 hours or turn
the appliance on and off.
Up And Down Buttons
Use the up and down buttons to:
• Set desired temperature when in
cooling mode and heating mode.
• Set desired hours till turn-on and
turn-off when setting a timer.
• Change between °C and °F by
pressing both down at the same time.
Swing Button (Remote Control Only)
Activate the swinging louvre ensuring
continuous air circulation.
Note: Should a constant wind ow
direction be required in place of
continuous air circulation simply manually
position the louvre to the desired angle.
Temperature Unit Change Button
(Remote Control Only)
Change the temperature units between
°C and °F.

12 | English
WiFi And Smart Life App
Set-Up
To connect the appliance to a smartphone
via WiFi through the Smart Life app follow
the below steps.
Note: Ensure WiFi network is set to
2.4GHz.
1. Download the Smart Life app by
Tuya Inc from the Apple App Store or
Google Play Store.
2. Register for a Smart Life account.
3. Log into the Smart Life app.
4. On the Home page tap Add Device
or the + symbol in the top right hand
corner.
5. Tap Large Home Appliances.
6. Tap Air Conditioner.
7. Plug in the appliance and ensure the
power socket is turned on.
8. Press the power button to turn on the
appliance and then press the power
button again to turn off the appliance
and place it in standby mode.
9. Press and hold the fan speed button
for three seconds to activate the
appliances WiFi pairing function.
After three seconds the WiFi indicator
light will begin to blink.
10. Tap Conrm WiFi Indicator Light
Rapidly Blinking.
11. Input WiFi password and tap
Conrm.
12. The Smart Life app will automatically
connect to the appliance and show
Successfully Added Device.
13. Return to the Smart Life app home
page and tap the appliances name.
14. Use the controls to fully control the
appliance and set desired settings
etc.
Amazon Echo Set-Up
To connect the appliance to an Amazon
Echo device via WiFi follow the below
steps.
Notes:
• The Smart Life app must have
already been downloaded and the
appliance successfully paired with
the Smart Life app.
• The Amazon Alexa app must have
already been downloaded.
• An Amazon Echo device must be
paired with the Amazon Alexa app.
1. Link the Amazon Alexa app to the
Smart Life app:
1. Open the Amazon Alexa app.
2. Go to Skills.
3. Search for Smart Life by Tuya Inc.
4. Tap Enable.
5. Follow the on-screen instructions to
connect your Smart Life account with
the Amazon Alexa app.
2. Pair the Amazon Alexa app to the
appliance:
1. Open the Amazon Alexa app.
2. Go to Devices.
3. Tap the + symbol to add a new
device.
4. Tap the appliances name and follow
the on-screen instructions to pair the
Amazon Alexa app to the appliance.
5. Use Amazon Alexa to control the
appliance e.g. “Alexa, turn on the air
conditioner.”.

English | 13
Google Home Set-Up
To connect the appliance to a Google
Home device via WiFi follow the below
steps.
Notes:
• The Smart Life app must have
already been downloaded and the
appliance successfully paired with
the Smart Life app.
• The Google Home app must have
already been downloaded.
• A Google Home device must be
paired with the Google Home app.
1. Open the Google Home app.
2. Tap the + symbol.
3. Tap Set up device.
4. Tap Have something already set up?
5. Search for Smart Life by Tuya Inc.
6. Follow the on-screen instructions
to connect your Smart Life account
with and the appliance to the Google
Home app.
7. Return to the Google Home home
screen.
8. Tap the room assigned to the
appliance and tap the appliances
name.
9. Use Google Assistant to control the
appliance e.g. “Hey Google, turn on
the air conditioner.”.

14 | English
Emptying The Water Tank
When the water tank is full the warning
FL will show on the display and the
appliance will pause operation to prevent
the water tank from overowing.
To empty the water tank:
1. Turn off the appliance and unplug it
from the wall socket.
2. Place a shallow tray underneath the
water outlet.
3. Unscrew the bottom drainage cap,
unplug the drainage plug and allow
the water to collect in the shallow
tray.
4. To fully empty the water tank gently
tilt the appliance back on its rear
wheels. Do not tilt more than 30
degrees.
5. Once empty, return the appliance to a
fully upright position and replace the
drainage plug and bottom drainage
cap.
6. Empty the shallow tray.
Note: If the shallow tray is not large
enough to hold all of the water from the
appliance replace the drainage cap to
prevent water from owing onto the oor.
Empty the shallow tray and continue from
step 2.
Bottom
drainage cap
Drainage plug
Water outlet
3
4
30º
Shallow tray
2

English | 15
Connecting The Water
Hose for Continuous
Drainage
For long-term use, it is recommended
to connect a water hose for continuous
drainage.
To attach the water hose:
1. Unscrew the continuous drainage
cap and unplug the drainage plug.
2. Insert the water hose into the water
outlet.
3. Ensure the water hose end has a
suitable drainage outlet (e.g a drain or
bucket).
Note: When the appliance is set at a
warm temperature it is recommended to
attach the water hose as the water tank
will ll at a faster rate than when set at a
cold temperature.
1
2
Water hose

16 | English
Cleaning
General Cleaning
Turn off the appliance and unplug it from
the power socket. Use a soft, dry cloth to
clean away any dust, or debris from the
exterior surface of the appliance.
Heat Exhaust Pipe Cleaning
1. Remove the heat exhaust pipe from
the rear of the appliance and the
respective window sealing assembly.
2. Use a soft, dry cloth to clean away
any dust, or debris.
3. Return the heat exhaust pipe.
Filter Cleaning
Clean the appliance’s evaporator and
condenser lter once every two weeks.
To remove and clean the evaporator lter:
1. Grip the evaporator lter cover top
gripping position and gently remove.
2. Unscrew the four screws securing the
evaporative lter to the appliance.
3. Use a rm brush and/or vacuum
cleaner to clean the lter of any dust
and particles.
4. Return the evaporator lter and screw
back into position.
5. Return the evaporator lter cover.
To remove and clean the condenser lter:
1. Grip the condenser lter at the
gripping position and gently remove.
2. Use a rm brush and/or vacuum
cleaner to clean the lter of any dust
and particles.
3. Return the condenser lter.
Gripping position
Gripping position

English | 17
Storage
For long-term storage:
1. Empty the water tank and leave both
the continuous and bottom drainage
caps and drainage plugs off and
unplugged.
2. Run the appliance in fan-only mode
on the low fan speed setting for 12
hours to allow the interior of the
appliance to fully dry.
3. Turn off the appliance, replace both
the continuous and bottom drainage
caps and drainage plugs, and unplug
the power cord.
4. Remove the heat exhaust hose.
5. Remove the batteries from the
remote control.
6. Cover the appliance and all
accessories with a waterproof
covering and store in a safe, dry
place, out of the reach of children.
Safety Features
Anti-Frost Protection
If the internal pipe temperature drops too
low the compressor and water spraying
motor will turn off. The display will show
E4 and the appliance will initiate anti-
frost protection rendering the control
panel buttons inactive apart from the
power button. Once the internal pipe
temperature has warmed the anti-frost
protection will cease and the appliance
will return to operating at the chosen
settings.
Anti-Overheat Protection
If the internal pipe temperature rises
too high the compressor will turn off
and the appliance will initiate anti-
overheat protection rendering the control
panel buttons inactive apart from the
power button. Once the internal pipe
temperature has cooled the anti-overheat
protection will cease and the appliance
will return to operating at the chosen
settings.
Automatic Defrosting
If the internal pipe temperature is too
low upon turning on the appliance and
selecting heating mode or drops too
low whilst operating in heating mode
the heating mode indicator light will
ash and the appliance will initiate
automatic defrosting rendering the control
panel buttons inactive apart from the
power button. Once the internal pipe
temperature has warmed the automatic
defrosting will cease and the appliance
will return to operating at the chosen
settings.

18 | English
Compressor Delay Protection
To protect the compressor, apart from
when the appliance and compressor are
activated for the rst time after being
turned on via the power button, there will
be a three minute delay between every
occurrence of the compressor turning off
and on.
Disposal
This marking indicates that this product
should not be disposed of with other
household waste throughout the EU.
This is to prevent the possible harm
to the environment and human well-
being. Contact your local authority for
information regarding the collection
systems available. If possible, recycle it
responsibly to promote the sustainable
reuse of resources.

English | 19
Helpful Information
Issue Cause Resolution
The appliance is not operating.
No power. Connect the unit to a live power
socket and turn it on.
Water tank full. Drain the water stored in the
unit.
Room temperature too low. It is recommended that this unit
be operated at 5-32°C.
Room temperature lower than
the set temperature in cooling
mode.
Increase the set temperature
above the room temperature.
Poor cooling.
Doors and windows are open or
there are other heat sources.
Close doors and windows and
remove other heat sources.
Dirty lters. Clean lters.
Air inlet or air outlet clogged. Remove the obstruction.
There is direct sunlight. Draw curtains.
Noisy. Appliance not on a at surface. Place the appliance on a at
surface.
The compressor does not work. Initiation of overheat protection.
Wait three minutes until the
temperature decreases and
then turn on the unit.
The remote control does not
work.
Too far from appliance. Bring the remote control closer
to the appliance and ensure
that the remote control is
pointing toward the receiving
head of the remote control.
The remote control is not
pointing towards the receiving
head of the remote control.
The batteries are dead. Replace the batteries.
Display showing E1. Pipe temperature sensor failure.
Arrange for a professional to
check the pipe temperature
sensor and related circuits.
Display showing E2. Room temperature sensor
failure.
Arrange for a professional to
check the room temperature
sensor and related circuits.
Display showing E4. Anti-frost protection.
Appliance returns to operating
at chosen settings once the
internal pipe temperature
exceeds 8°C.

20 | Deutsch
Mobiles Klimagerät
Vielen Dank, dass Sie sich für ein Produkt von Pro Breeze entschieden haben. Bitte
lesen Sie die gesamte Anleitung vor dem ersten Gebrauch sorgfältig durch und
bewahren Sie sie zum späteren Nachschlagen an einem sicheren Ort auf.
Sicherheitshinweise
• Verwenden Sie das Gerät nur
gemäß der Beschreibung in dieser
Bedienungsanleitung.
• Prüfen Sie vor der Inbetriebnahme,
ob die Netzspannung mit
der Spannung des Gerätes
übereinstimmt.
• Dieses Gerät ist ausschließlich für die
Verwendung im Haushalt bestimmt.
• Das Gerät ist kein Spielzeug. Lassen
Sie das Gerät niemals unbeaufsichtigt
in der Nähe von Kindern oder
Haustieren stehen.
• Das Gerät darf von Kindern ab
acht Jahren und von Personen
mit eingeschränkten körperlichen,
sensorischen bzw. geistigen
Fähigkeiten oder mangelnder
Erfahrung bzw. Kenntnis nur dann
verwendet werden, wenn diese
beaufsichtigt werden bzw. eine
Einweisung in die sichere Nutzung
des Gerätes erhalten haben und die
damit verbundenen Risiken kennen.
• Kinder dürfen nicht mit diesem Gerät
spielen.
• Reinigung und Wartung darf nur
durch Kinder erfolgen, wenn diese
durch Erwachsene entsprechend
überwacht werden.
• Bewahren Sie das Gerät und
sämtliche Teile außerhalb der
Inhaltsverzeichnis Pg
Sicherheitswarnung 20
Spezische Information zu dem R290 Kältemittel 22
Vorsicht | Technische Daten 23
Teile 24
Bedienfeld 25
App Einrichten 26
Bedienelemente 28
Wassertank Entleeren 32
Anschließen des Wasserablaufschlauchs für permanenten Wasserablauf 33
Reinigung | Einlagerung des Geräts | Schutzfunktionen 34-35
Entsorgung 36
Nützliche Informationen 37