Pro Dunk Wall King User manual

1
OWNER’S
MANUAL
Warning
 ! Do not slide, climb, or
play on system.
 ! Keep organic material
away from system.
Grass, litter, etc. could
cause corrosion and /or
deterioration.
 ! Check system twice a
year for signs of corro-
sion (rust, pitting, and
chipping). Remove rust
and/or loose paint com-
pletely and repaint with
exterior enamel paint. If
rust has penetrated
through the steel any-
where, replace parts
immediately.
 ! Check unit before
each use for loose
hardware, excessive
wear, and signs of cor-
rosion and repair be-
fore using.
 ! During play, use ex-
treme caution to keep
players face away from
the backboard, rim, and
net.
 ! Wear a mouth guard
when playing to avoid
dental injuries.
 ! When adjusting
height, keep hands and
fingers away from mov-
ing parts.
 ! During play, do not
wear jewelry (rings,
watches, necklaces,
etc.). Objects may en-
tangle in net.
Basketball System
WELCOME TO THE FAMILY OF
PRO DUNK®OWNERS
Thank you for purchasing our basketball system. We try hard to ensure that our
products are of high quality and free of manufacturing defects and of missing
parts. However, if you have any problems with your basketball pole, such as a
manufacturing defect or a missing part please contact us at the following:
Toll Free: 1.888.600.8545 Pro Dunk®
Web: www.produnk.com 22047 Lutheran Church Rd.
Tomball, TX 77377
Please provide model number, serial number, and/or part number of the product
and/or part when you call, write or email. These numbers can be found on the
product, packaging, or on the back of the main pole.
Purchase Parts: www.produnk.com/parts
Support: www.produnk.com/support
Installation Video: www.produnk.com/video/wall_king_installation.php
Read this manual all the way through before starting to
install your system. Then read each step completely
before beginning installation. Ensure you understand
each step fully and comply with all steps for a safe
installation.
Pro Dunk® WALL KING

2
Bill Of Materials
No. Description Qty.
1 Wall Bracket 1
2 Upper Extension Arm 1
3 Lower Extension Arm 1
4 Backboard 1
5 Rim 1
6 Rim Cover Plate (Packaged With Rim) 1
7 Actuator 1
8 Upper Actuator Arm 2
9 Lower Actuator Arm 2
10 Steel Height Meter 1
11 Actuator Handle 1
12 Backboard Connection Bracket 2
13 Rear Wall Support Bracket 4
14 Actuator Steel Sleeve 1
15 Plastic and Steel Rim Spacer 4
16 16mm x 58cm Hex Bolt 1
17 16mm x 52cm Hex Bolt 1
18 16mm x 13cm Hex Bolt 2
19 12mm x 8mm Hex Bolt 2
20 12mm x 7mm Hex Bolt 4
21 12mm x 3.5cm Hex Bolt 2
22 10mm x 35cm Hex Bolt 6
23 10mm x 35cm Eye Bolt 1
24 10mm x 7cm Hex Bolt (Packaged With Rim) 4
25 6mm x Phillips Bolt (Packaged With Rim) 2
26 16mm Nylon Hex Locknut 4
27 12mm Nylon Hex Locknut 8
28 10mm Hex Nut 4
29 16mm Flat Washer 8
30 12mm Flat Washer 16
31 10mm Flat Washer 14
32 10mm Flat Washer 12
33 10mm Lock Washer 4
34 Safety Cable Clip 1
35 Safety Cable Mounting Bracket 1
36 Steel Safety Cable 2
37 10mm Nylon Hex Locknut 7
38 Masonry Drill Bit 1
39 Wood Drill Bit 1
40 Height Sticker 1

3
Safety Instructions
 All tools used to assemble this product
should be used in compliance with manu-
facturer’s guidelines.
 Installation of this product will require
heavy lifting and bending. Any person that
is not capable of such activity should not
participate in the installation of this product.
 If using a ladder during assemble, use ex-
treme caution and refer to the warnings
and cautions on the ladder.
 Due to the size and weight of this product,
we recommend at least (4) competent
adults are present.
 Make sure there are no overhead power
lines within a 25 foot radius of the basket-
ball system.
 All parts and components necessary to
complete proper installation are included
within this product. Do not use parts not
included with our system. Failure to follow
this requirement could cause product mal-
function and will void warranty of this prod-
uct.
 Keep all organic materials away from parts
and components to avoid corrosion.
 Do not Dunk or Hang on your system.
 Do not climb on any part of the basketball
system as it was not intended for this activ-
ity.
 The owner is responsible for ensuring the
wall or structure the system is mounted to
is structurally sound and capable of sup-
porting the stress of the system. Contact a
professional engineer evaluate your struc-
ture beforehand.
IMPORTANT
It is the responsibility of purchaser to ensure that
all installers and players fully comply with the de-
tailed instructions set forth in this product installa-
tion manual. Product assembly should be carried
out exactly as instructed and owner supervision
of use and installation is required to prevent risk
of product malfunction or risk injury.
Pro Dunk® retains the right to modify this
document at any time without notice or
obligation.
Keep this installation manual as a refer-
ence for your safety and the safety of
those playing on the basketball system.
Additional copies of these safety instruc-
tions are available by calling customer
service at 1.888.600.8545 or at
www.produnk.com/support
 Do not use the basketball system as a lift or to
hoist anything.
 Players should wear protective mouth guard
during play to avoid any time of dental injury.
 Players should refrain from wearing any jew-
elry that could potentially get caught in the rim
or net.
 Do not allow children to adjust basketball sys-
tem.
 Check the basketball system on a regular ba-
sis to ensure that there are no signs of dete-
rioration or corrosion, loose hardware, or
damaged parts. If you see any signs of dam-
age perform maintenance or contact Pro
Dunk® for replacement.
 For maintenance repairs please contact a pro-
fessional.
 During installation be sure the wall is clear of
any type of utilities (wires, gas lines, water
lines, etc..)
 Be sure you have safe access to the rear side
of the wall to complete the installation.
 Failure to follow these safety instructions
could result in product malfunction, seri-
ous injury, or even death.

4
Installation Overview
In order to have the safest, fun and longest use of your Pro Dunk® system,
please note and heed the following:
1) Prior to goal assembly, ensure the structure the system is being
mounted to is structurally sound and capable of supporting the
system. We recommend contacting an engineer to evaluate to
structure as well.
2) Installation requires full access to the rear side of the structure.
3) Immediately unpack all components and cross check against bill
of materials. Report any shortages to Hoops Inc. customer ser-
vice at 1.888.600.8545.
4) Parts can be ordered at www.produnk.com/parts
5) For safety measures, have at least 4 capable persons to assist
you in assembly of your system.
Required Tools
 Power Drill (Hammer drill for brick and stone)
 2 Adjustable Wenches
 #2 Phillips Screw Driver
 2 8ft Ladders
 Level
 Pencil
 Tape Measure
 24mm
 22mm
 17mm
Socket/Wrench Sizes
Recommended
www.produnk.com/video/wall_king_installation.php
Wall King Installation Video

5
Pro Dunk Accessories
Need a dedicated net or lighting for your court. Our
Boundary Netting has got your covered. This accessory is
fully customizable and is a standalone net, light, and/or flag.
Below is a link to our builder. Customize your court!
Comes with Free Shipping!
Goal Light LED!
produnk.com/video/goal_light_led.html
http://www.produnk.com/basketball_goals/accessories/
Dedicated Net
produnk.com/video/boundary_netting.html
Court Marking Stencil
produnk.com/video/court_marking_stencil_kit.html
Why stop playing in the evening. You don’t have to! Order the
Pro Dunk Goal Light LED. It easily lights up the entire 3-point
line with 2 powerful LED lamps extending play into the night.
There’s always time for one more game!
[patent pending 62458721]
Comes with Free Shipping!
Looking to light up your court from multiple locations? The Pole Light LED
can be mounted anywhere and will light up your entire court. You can have
multiple sources of light to cancel out any shadows during place and truly
bring the gym experience home! This even has a flag option to put up your
favorite flag and fly it proud!
Comes with Free Shipping!
Haven’t you always wanted your playing area to have regulation
striping like a real basketball court. Well now you can with the
Court Marking Stencil Kit. Just lay it out on your court and ap-
plied the included white paint. Includes the key with side
markings, freethow, and the entire 3-point line. Fully reus-
able and a great family DIY project.
Comes with Free Shipping!
Pole Light LED
produnk.com/video/pole_light_led.html

6
Installation
1) Installation Location
Choose the proper location to mount your Wall King system.
Use the diagram to the left to make sure your bracket is high
enough to be adjusted up to 10ft. If you install your bracket
higher than 86 inches your system will still adjust to 10ft but
will not adjust down as far. If you install your bracket below 86
inches your system will not adjust up to 10ft.
The wall surface needs to be level and flat so that your
bracket will be level. The wall must either be wood siding,
brick, or stone and be structurally sound.
Ensure that the structure you are mounting to is structurally
sound and sufficient to handle the stresses of the Wall King.
Contact a professional engineer regarding this.
Above your bracket you need an additional 6 - 16 inches for
the safety cable to attach to the wall (16 inches being optimal).
You must have full access to the rear side of the wall to
complete the installation.
Before moving on confirm you have read and understand
all safety instructions on page 3.
The overhang is 3ft from the wall to the front of the backboard.
2) Marking and Drilling Bracket Mounting Holes
Using a pencil, mark the 2 top mounting holes, 2 bottom
holes, 2 of the 6 center holes (1 on the left and 1 on the right),
and the safety cable eye bolt hole while ensuring the bracket
is level. (Total of 7 holes to be drilled)
Once marked check the wall to make sure there is nothing in
the way of drilling through the wall. Example: electric wiring,
steel braces/studs, water lines, gas lines, or anything else.
Brick/Stone Wall:
Next using the provided drill bit(s), drill each hole. Use the
#38 masonry drill bit and a hammer drill to go through the
brick or stone. Once through the brick or stone switch to the
#39 wood drill bit to go through the rest of the wall.
Wood/Siding Wall:
Using the #39 wood drill bit, drill each hole.

7
3) Bracket Installation
Rear access to the wall is required to mount the wall bracket.
Next install your #1 wall bracket to the wall using the 6 #22 bolts, 12 #31
flat washers, 6 #37 hex nuts, and 3 #13 rear wall support brackets.
Before tightening make sure bracket is level.
Parts:
[1] #1 Wall Bracket
[3] #13 Rear Wall Support Brackets
Hardware:
[6] #22 10mm x 35cm Hex Bolts
[12] #31 10mm Flat Washers
[6] #37 10mm Nylon Hex Locknut
5) Extension Arm Assembly
Once your bracket is secured to the wall it is now time to assemble the upper and lower extension
arms.
Parts:
[1] #2 Upper Extension Arm
[1] #3 Lower Extension Arm
[2] #8 Upper Actuator Arms
Hardware:
[4] #20 12mm x 7cm Hex Bolts
[8] #30 Flat Washers
[4] #27 12mm Nylon Hex Locknuts
4) Safety Eye Bolt
Install your safety eye bolt through your wall.
Parts:
[1] #13 Rear Wall Support Bracket
Hardware:
[1] #20 12mm x 7cm Eye Bolt
[2] #31 Flat Washers
[1] #37 10mm Nylon Hex Locknut

8
6) Actuator Assembly
Next assemble your actuator as shown to the right.
Parts:
[1] #7 Actuator
[2] #9 Lower Actuator Arms
[1] #14 Actuator Steel Sleeve
[1] #10 Steel Height Meter
[1] #11 Actuator Handle
Hardware:
[2] #18 16mm x 13cm Hex Bolts
[4] #29 16mm Flat Washers
[2] #26 16mm Nylon Hex Locknut
[2] #21 12mm x 3.5cm Hex Bolts
[4] #30 12mm Flat Washers
[2] #27 12mm Nylon Hex Locknut
7) Backboard Assembly
Next assemble your Backboard Connection Brackets and backboard
as shown above.
Parts:
[1] #4 Backboard
[2] #12 Backboard Connection Brackets
Hardware:
[1] #17 16mm x 52cm Hex Bolt
[1] #16 16mm x 58cm Hex Bolt
[4] #29 16mm Flat Washers
[2] #26 16mm Nylon Hex Lock-
Hardware Continued:
[2] #19 12mm x 8cm Hex Bolts
[4] #30 12mm Flat Washers
[2] #27 12mm Nylon Hex Locknut

9
8) Rim Assembly
Next assemble your rim as shown to the right
and level rim left to right.
Parts:
[1] #5 Rim
[1] #6 Rim Cover Plate (Packaged With Rim)
[4] #15 Plastic and Steel Rim Spacer
Hardware (Packaged With Rim):
[4] #24 10mm x 7cm Hex Bolts
[8] #32 10mm Flat Washers
[4] #33 10mm Lock Washer
[4] #28 10mm Hex Nut
[2] #25 6mm Phillips Bolt
Make sure all hardware on the
system is tightened at this point.
9) Safety Cable Assembly
Next assemble the #34 Safety Cable
Mounting Bracket to your Backboard.
Loosen the 2 H-Bracket bolts and in-
stall the #34 Safety Cable Mounting
Bracket to the top of the backboard as
shown.
Once secured connect the #35 Steel
Safety Cable using the 2 #36 Safety
Cable Clips as shown.
Parts:
[1] #34 Safety Cable Mounting Bracket
[2] #36 Safety Cable Clips
[1] #35 Steel Safety Cable
CAUTION: Do not proceed with
rim assembly without these spacers!
Install Rim Spacers
produnk.com/video/rim_spacer.html

10
10) Height Sticker Assembly
To apply the #40 Height Sticker, first use a tape measure to crank rim up to exactly 10' from the
playing surface. This is measured from the top of the rim to the playing area. Then apply your #40
Height Sticker to the actuator where the #10 Height Meter is pointing at 10ft exactly. Your system is
now calibrated and you will have a general idea of what height the system is at while adjusting it up
and down.
Please remember if you did not mount your bracket at exactly 86” you will not have the full range of
adjustment and will need to understand the limitations. You can reference Step 1 or give our sup-
port staff a call if you have any questions.
11) Routine System Inspection and Safety Before Play
Before each use inspect the entire system for any signs of loose nuts and bolts, any excessive wear
and tear, any signs of rust or corrosion.
If replacement parts are needed you can contact Pro Dunk® directly or navigate to
www.produnk.com/parts to purchase parts for your system. Only parts provided by Pro Dunk®
should be used for repair. Not doing so could cause the system to fail resulting in injury or death
and voids the limited lifetime warranty.
Be sure you and all players have read and fully understand all safety warnings on page 3.
DO NOT DUNK OR HANG ON THIS BASKETBALL SYSTEM.
12) Maintenance
Like any piece of hardware proper maintenance is required. Several factors such as the environ-
ment, organic materials, herbicides, pesticides, excessive use or misuse can eventually cause the
basketball system to require maintenance. Failure to do so could result in system failure, property
damage, or even personal injury.
1) All organic materials should be kept away from the system at all times. This will alleviate any
chance of rust penetrating the powder coated finish and causing structural damage.
Examples: grass clippings, moisture, garbage, dirt, etc.
2) If you see any signs of rust on the system remove the loose paint, sand the area with a media grit
sandpaper and apply outdoor enamel to the affected area.
Suggested Touchup Paint: Rustoleum Semi-Gloss Black Enamel
3) To clean the backboard use a 100% cotton soft cloth with mild dishwashing liquid for soap and
luke warm water. Rinse backboard with lukewarm water. Wash gently with a 100% Cotton soft
cloth, lukewarm water and mild soap. Do not scrub. Rinse backboard with lukewarm water again.
Dry with 100% cotton soft cloth. To minimize scratches and minor abrasions to your backboard
4) Never adjust the rim outside the adjustment range based on your installation. Adjustments of the
goal should be done under adult supervision.
5) If installed in a public area it is suggested to remove the adjustment handle.
6) Replace Net Video—Replace Net
produnk.com/video/rim_net_replacement.html 2-17-2020

11
Hoops Inc. Pro Dunk® WALL KING Limited 5 Year Warranty
Hoops Pro Dunk® WALL KING basketball structural components are warranted to the original purchaser to be free
from defects in material or workmanship for the duration of ownership by the original retail purchaser. The word
“defects” is defined as imperfections that impair the use of the product.
Warranty Fulfillment
Merchandise must be shipped prepaid with a copy of proof of purchase to Hoops Inc. for examination to see whether it
needs to be repaired or replaced. Any labor costs, travel expenses and any other changes involved in the removal,
installation or replacement of the defective/repaired parts from/to your Hoops Pro Dunk® WALL KING system will be
your (the purchaser's) responsibility. Shipping charges for replaced or warranted merchandise being sent back to the
customer must be prepaid by the customer in advance. If not, the replacement shipment will be sent out collect.
Hoops Inc. reserves the right to examine photographs or physical evidence of merchandise claimed to be defective,
and to recover said merchandise, prior to authorization of warranty claims.
What is not covered by this warranty
This warranty does not cover defects or damage due to improper installation, shipping, handling, alteration, accidents,
vandalism, weather conditions (rusting), exposure to corrosives, negligence, misuse (anything other than a type of
basketball activity or related contact with the unit), scratching, scuffing or any event beyond the control of the Hoops
Inc.. If unit is not maintained as stated in the user manual the warranty will be void.
Liability
Hoops Inc. shall not be liable for indirect, special, or consequential damages arising out of or in connection with the
use or performance of the products or other damages with respect to any economical loss, loss of property, loss of
enjoyment of use, costs of removal, installation or other consequential damages for breach of any expressed or im-
plied warranty on these products. All installations must have a final engineering signoff before use and yearly inspec-
tions by a professional certified to do so or specified by the engineer.
Guidelines
Keep your proof of purchase (original retail purchaser). Without it, we will not be able to proceed with any warranty
service.
Call
1-888-600-8545 / Warranty Dept.
Write
Hoops Inc.
Attn: Warranty Dept
22047 Lutheran Church Rd.
Tomball TX 77377
Email
[e-mail]
For the most up to date warranty information please navigate to www.produnk.com.