Pro-gard Products LLC. 3G7009A User manual

pro-gard.com
800.480.6680
INSTALLATION GUIDE
3G7009A
SELF SUPPORTING GUN RACK
2016-2020 FORD F150 SUPERCREW
RELE ASED 11.8.2021

pro-gard.com
800.480.6680
2
PARTS LIST
DESCRIPTIONPART NUMBERQTYITEM
GUN RACK MOUNT BASE3G7036-0111
GUN RACK MOUNT FOOT - DRIVER3G7036-0212
GUN RACK MOUNT FOOT - PASSENGER3G7036-0313
1/4" INT TOOTH LOCK WSHR3X34b44
1/4"-14x1" SELF DRILLING SCREW3X11045
1/4-20x0.75, SBHCS, BLACK OXIDE3X18446
GUN RACK CHAIR3G7009APackage17
GUN LOCKG4904-NPG18
GUN LOCKG4904H19
PLASTIC BACKING3G7009C110
8-32 X 5/8 PHIL PAN HD MS3X143411
BUTT PLATEG4962-002212
1/4-20 X 0.75, SBHCS, BLACK OSIDE3X184413
RUPPER PAD3G4963-002214
1
1
2
2
3
3
4
4
A A
B B
C C
D D
* = QTY MAY VARY DEPENDING ON CONFIGURATION
** = ITEM MAY VARY DEPENDING ON CONFIGURATION
I. Refer to the diagram on the last page of these instructions to verify all parts were received.
II. The following tools will be required to complete the installation.
Socket wrench with 7/16” socket
Allen tool 5/32 or 4mm
Phillips screw driver
III. Installing the gun rack.
A. Remove the four 3X184 allen bolts that hold the butt plates to in place. Rest the gun rack, 3G7009A
on the previously installed self supporting stand (refer to vehicle mounting instructions). Install the
four 3X184 bolts back into the butt plate slots securing the gun rack and butt plates to mounting base.
(Leave these bolts loose for now to allow movement of the gun rack on the base).
GVM180 GUN RACK
3G7009A
FIG. 1
IV. Weapontment.
A. Remove the 4 philips head screws (3X143)that secure
black plastic ABS back to the gun rack. Remove the back
cover from the gun rack to access the gun lock fasteners
and adjust as needed.
B. Place weapon in the gun rack and adjust lock and butt
plate bracket to properly t weapon.
Optional - Charging brackets and trigger guards
should also be adjusted to ensure the weapon cannot
be discharged.
V. Final installation.
A. Wire electric gun locks per timer instructions.
See page 4
B. Re-install the back cover onto the gunrack with the 4
(3X143) screws that were removed earlier.

3
VI. Lock Head Operating Instructions
To release the weapon:
A. Grasp the weapon, but do not pull it against the lid of the gun lock.
B. While depressing and holding the release button (momentary switch), push and then
pull the weapon towards the lid of the gun lock to release it from the lock.
Note: One handed operation is possible utilizing the optional 8 second timer. The
timer will unlock the lock for 8 seconds following activation of the momentary
switch. If the gun is not pulled out of the lock within 8 seconds after activation of
the momentary switch, the lock will automatically re-lock.
Important: If the lid of the lock does not release, press in on the lid to release tension
and reactivate the release button (unless timer is still active).
VII. Securing the Weapon:
A. Push weapon rmly and completely into the lock mechanism and rmly close lid.
B. Check to insure that the lid is locked.
C. If the lid does not lock, re-seat the weapon rmly and completely into the lock assembly
and again apply pressure to the lock lid to seat and re-lock it.
Note: The G4904 Series lock mechanism has a unique override. In the event of power
failure, the lock can be opened using a standard handcu key or other high security key.
VIII. To open the lock with the manual override key:
A. Fully insert the handcu key into the hole provided in the lock head. Turn the key 1/4 turn to the
left (counter-clockwise). Pull open the lid or pull on the weapon to open it.
Important: Return the key to its original position or remove key completely to close and re-lock
the lock.

pro-gard.com
800.480.6680
4
IX. Installing Optional 8 second timer (3-Wire)
Note: If for any reason the gun lock momentary switch remains activated, such as, the button is
damaged, and/or shorted, the unit will time out in 8 seconds and can not be operated again until
the defective switch is repaired, thus saving the gun lock solenoid. Do not connect directly to
power for more than 20 seconds!
X. Installation Complete
PARTS LIST
DESCRIPTIONPART NUMBERQTYITEM
GUN RACK - VERTICAL MOUNT3G7009A11
GUN LOCK SPACER**3G5085*12
LOCK MEDIUM STYLE R**G4904-NPG*13
LOCK SMALL STYLE H**G4904H*14
BACK COVER - ABS PLASTIC3G7009C15
BUTT PLATE - BLACK NYLONG4962-00226
RUBBER BUTT PLATE PADG4963-00227
SWITCH, MOMENTARY (NOT SHOWN)3G510018
CHARGING HANDLE BRACKET (NOT SHOWN)3G907919
TIMER-8 SECOND DELAY - 3 WIRE (NOT SHOWN)G1002110
HARDWARE LIST
DESCRIPTION
PART NUMBER
QTY
ITEM
1/4-20 X 5/8 PHIL TRUSS HD MS (NOT SHOWN)3X03*2
11
1/4-20 HEX WHIZ NUT - BLACK OXIDE (NOT SHOWN)3X16*212
1/4" STANDARD FLAT WASHER3X33
4
13
5/16 MED SPLIT LOCKWASHER - ZC (NOT SHOWN)3X58
414
5/16-18 X 1 HEX HD - CAP SCR3X75*2
15
5/16-18 x 1-1/4" CAP SCREW3X98*216
8-32 X 5/8 PHIL PAN HD MS3X143
417
1/4/20X0.75, SBHCS - BLACK OXIDE3X184
4
18
1
1
2
2
3
3
4
4
A A
B B
C C
D D
5
17
6
7
18
34
2
1
13
16
* - QTY MAY VARY DEPENDING ON CONFIGURATION
** - ITEM MAY VARY DEPENDING ON CONFIGURATION
15
PARTS LIST
DESCRIPTIONPART NUMBERQTYITEM
GUN RACK - VERTICAL MOUNT3G7009A11
GUN LOCK SPACER**3G5085*12
LOCK MEDIUM STYLE R**G4904-NPG*13
LOCK SMALL STYLE H**G4904H*14
BACK COVER - ABS PLASTIC3G7009C15
BUTT PLATE - BLACK NYLONG4962-00226
RUBBER BUTT PLATE PADG4963-00227
SWITCH, MOMENTARY (NOT SHOWN)3G510018
CHARGING HANDLE BRACKET (NOT SHOWN)3G907919
TIMER-8 SECOND DELAY - 3 WIRE (NOT SHOWN)G1002110
HARDWARE LIST
DESCRIPTION
PART NUMBER
QTY
ITEM
1/4-20 X 5/8 PHIL TRUSS HD MS (NOT SHOWN)3X03*2
11
1/4-20 HEX WHIZ NUT - BLACK OXIDE (NOT SHOWN)3X16*212
1/4" STANDARD FLAT WASHER3X33
4
13
5/16 MED SPLIT LOCKWASHER - ZC (NOT SHOWN)3X58
414
5/16-18 X 1 HEX HD - CAP SCR3X75*2
15
5/16-18 x 1-1/4" CAP SCREW3X98*216
8-32 X 5/8 PHIL PAN HD MS3X143
417
1/4/20X0.75, SBHCS - BLACK OXIDE3X184
4
18
1
1
2
2
3
3
4
4
A A
B B
C C
D D
5
17
6
7
18
34
2
1
13
16
* - QTY MAY VARY DEPENDING ON CONFIGURATION
** - ITEM MAY VARY DEPENDING ON CONFIGURATION
15

5
XI. Gun lock switch and timer installation.
A. We suggest mounting the momentary release button in a concealed location that can be easily
reached by the o󰀩cer, but would be hidden in case an unathorized entry occurs.
B. Connect the gun lock wiring as shown in the diagram below.
Pro-gard requires the use of a 10 AMP fuse between the power source and gun lock
circuit or the warranty will be voided!
XII. Lock Head Operating Instructions
A. To release, grasp the weapon, but do not pull it against the lid of the gun lock.
B. While depressing and holding the release button (momentary switch), push and then
pull the weapon towards the lid of the gun lock to release it from the lock.
One handed operation is possible utilizing the optional 8 second timer. The timer will
unlock the lock for 8 seconds following activation of the momentary switch. If the gun is
not pulled out of the lock within 8 seconds after activation of the momentary switch, the
lock will automatically re-lock.
If lid of the lock does not release, press in on the lid to release tension and reactivate the
release button (unless timer is still active).
Installation Complete!
If you have any problems with this installation than call the toll free number (800-480-6680)
and ask for technical assistance.
NOTE:
Fig. 6
NOTE:
TIP:

pro-gard.com
800.480.6680
6
Self-Supporting Mounting Base
G8116FT
PARTS LIST
DESCRIPTIONPART NUMBERQTYITEM
BRACE, BASE REAR F-1503G8116-0611
SUPPORT ARM ASSY, DS3G8116-01D12
SUPPORT ARM ASSY, PS3G8116-01P13
3/8-16x1.50, Hex Tap Bolts, Grade 8, Yellow Zinc3X11924
UNDERBRACE ASSY, F-1503G8116-021
5
F-150 BASE PLATE ASSEMBLY3G8116-0316
1/4 FLAT WASHER, BLACK3X126
7
1/4-20x0.75, SBHCS, BLACK OXIDE3X18468
1
5
2
6
3
4
58
7