Pro-Lift T-3101 Instructions for use

Printed in China
T-3101-M1_082018
Operating Instructions & Parts Manual
Engine Stand
Model Number
T-3101
Capacity
1000 lb
Shinn Fu Company of America, Inc.
10939 N. Pomona Ave.
Kansas City, MO 64153
Phone [phone], fax [phone]
© Aug. 2018
To avoid crushing and related
injuries: NEVER work on, under
or around a vehicle supported
by dollies.
WARNING: Cancer and Reproductive Harm.
AVERTISSEMENT: Cancer et dommages au système reproducteu
r.
ADVERTENCIA: Cáncer y daño reproductivo.
www.P65Warnings.ca.gov
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
!
!WARNING

2
Save these instructions. For your safety,
read and understand the information
contained within. The owner and operator
shall have an understanding of this product
and safe operating procedures before
attempting to use this product. Instructions
and safety information shall be conveyed in
the operator’s native language before use
of this product is authorized. Make certain
that the operator thoroughly understands
the inherent dangers associated with the
use and misuse of the product. If any doubt
exists as to the safe and proper use of this
product as outlined in this factory authorized
manual, remove from service. Inspect
before each use. Do not use if broken,
bent, cracked or otherwise damaged parts
are noted. If the engine stand has been
or suspected to have been subjected to a
shock load (a load dropped suddenly and
unexpectedly upon it), discontinue use
until checked out by an authorized factory
service center. Owners and operators of this
equipment shall be aware that the use of
this equipment may require special training
and knowledge. It is recommended that
an annual inspection be done by qualied
personnel and that any missing or damaged
parts, decals, warning/safety labels or
signs be replaced with factory authorized
replacement parts only. Any engine stand
that appears to be damaged in any way,
is worn or operated abnormally shall be
removed from service immediately. Labels
and owner’s manuals are available from
manufacturer (see Replacement Parts,
page 5).
PRODUCT DESCRIPTION
Pro-Lift Engine Stands are designed to
safely support rated capacity engines.
Welded steel tube construction, heavy
gauge steel plate head plates and mounting
arms along with compliance with factory
standards ensure safety, strength and
stability.
BEFORE USE
1. Inspect stands before each use. Do
not use if bent, broken or cracked
components are noted. Ensure that
casters/wheels and head plate rotate
freely. Check for and tighten any loose
assemblies.
2. Verify that the product and the application
are compatible.
3. Before using this product, read the
owner’s manual completely and
familiarize yourself thoroughly with the
product and the hazards associated with
its improper use.
Figure 1 - Typical Engine Stand
Nomenclature
rotating
mechanism
lock pin
handle
head plate
mounting arm
rear leg
center beam
front caster front leg
rear wheel
upright

3
Figure 2 - Assembly illustration for model
T-3101
ASSEMBLY
Model: T-3101 ( see Figure 2 )
Important: Reference numbers are for
assembly purpose only. See replacement
parts illustration for ordering replacement
parts.
1. Attach 2 front casters (Ref. No. 15) using
the lock washers (Ref. No. 13) and nuts
(Ref. No. 12).
2. Attach 2 rear wheels (Ref. No. 3) using
the washers (Ref. No. 2) and snap-rings
(Ref. No. 1).
3. Attach upright (Ref. No. 16) to the rear
leg (Ref. No. 4) using the M12 x 80 bolt
(Ref. No. 5), washer (Ref. No. 6), lock
washer (Ref. No. 7) and nally the hex
nut (Ref. No. 8).
4. Attach the center beam (Ref. No. 10) to
the front leg assy. (Ref. No. 11) using two
M12 x 80 bolts (Ref. No. 5), lock washer
(Ref. No. 7) and hex nut (Ref. No. 8).
5. Slide mounting plate (Ref. No. 20) into the
collar portion of the upright (Ref. No. 16),
align rotating position holes and insert
lock pin (Ref. No. 17).
6. Attach the four mounting adapter arms
(Ref. No. 21) to the slotted portion of the
mounting plate (Ref. No. 20) using M14
x 60 bolts (Ref. No. 22), lock washers
(Ref. No. 14), at washers (Ref. No. 13)
and hex nut (Ref. No. 12).
7. Insert handle (Ref. No. 19) into the hole
in the stem portion of the mounting plate
(Ref. No. 20) which protrudes from the
rear of the collar of the upright (Ref.
No. 16).
8. Attach the handle grips (Ref. No. 18)
onto both ends of handle (Ref. No. 19).
Study, understand, and follow all
instructions provided with and on this
device. Do not exceed rated capacity. Use
only on hard, level surface. Never put any
portion of your body under engine when it
is supported by the engine stand. Use only
hardened, appropriately sized bolts to
secure engine to stand. Center the engine
on mounting plate and ensure attaching
hardware is tightly fastened. Off center
loading may cause the engine to rotate
unexpectedly and cause the loaded stand
to tip over. Lock mounting plate rotating
mechanism before beginning engine
service. Unlock rotating mechanism
slowly and carefully. Do not modify or alter
this product. Do not use this device for
any purpose other than that for which it is
intended. Failure to heed these markings
may result in personal injury
!WARNING

4
OPERATION
1. Ensure application is compatible with
product.
2. Align engine with stand, then adjust
mounting arms to match bell housing
mounting bolt holes.
Rotational lock must be secure be-
fore applying load.
3. Carefully secure engine so that load is
centered on stand. Secure with suitable
high strength stud bolts and at wash-
ers. Ensure threads are compatible with
your engine. Use at washers on both
sides of head plate.
4. To rotate engine, carefully remove pin.
Use handle to rotate, then secure by
re-installing pin (Refer to Fig. 2).
5. Check to ensure stand is secure before
working on or around stand. Never work
under loaded stand.
Note: Do not move loaded stand off hard
smooth, level surface!
MAINTENANCE
Periodically inspect each stand. Ensure all
parts move freely. Apply very light coating of
grease to head plate collar. If rust appears,
sand affected area and cover with suitable
utility paint.

5
REPLACEMENT PARTS
Available Parts: Please refer to the parts drawing when ordering parts. Not all components
of the stand are replacement items, but are illustrated as a convenient reference of loca-
tion and position in the assembly sequence. When ordering parts, give model number,
serial number and description below. Call or write for current pricing: phone (816) 891-
6390, fax [phone] or contact Pro-Lift Customer Support. 10939 N. Pomona Ave.,
Kansas City, MO 64153.
Model T-3101
Part No. Description Quantity
1 head plate 1
2 mounting arm assembly 4
3 front Wheel assembly 2
4 rear Caster assembly 2
5 handle assembly 1
6 lock pin 1
7 hardware kit (not shown) all nuts and bolts
-- label 1
-- owner’s manual 1
Figure 4 - Replacement Parts Illustration for Model T-3101
65
1
2
3
4

6
ONE YEAR LIMITED WARRANTY
For a period of one (1) year from date of purchase, SFA Companies will repair
or replace, at its option, without charge, any of its products which fails due to a defect in
material or workmanship, or which fails to conform to any implied warranty not excluded
hereby.
Performance of any obligation under this warranty may be obtained by returning
the warranted product, freight prepaid, to SFA Companies Warranty Service Department,
10939 N. Pomona Ave., Kansas City, MO 64153.
Except where such limitations and exclusions are specically prohibited by ap-
plicable law, (1) the
CONSUMER’S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACE-
MENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE, and (2) SFA Companies
SHALL NOT BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER, and (3) THE
DURATION OF ANY AND ALL EXPRESSED AND IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, IS LIMITED TO A PERIOD OF ONE (1) YEAR FROM
DATE OF PURCHASE.
Some states do not allow limitations on how long an implied warranty lasts, so the
above limitation may not apply to you. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation or exclusion may not apply
to you. This warranty gives you specic legal rights, and you may also have other rights
which vary from state to state.

7
NOTES:

8
NOTES: