Pro-Lift WMH Series User manual





ThankyouforpurchasingaPro‐LIFTWMH.ThePro‐LIFTproductlineisdesignedtoenhanceyour
interactivewhiteboardsandprojectorsorLCD.Pleasefollowallassemblyinstructionscorrectlyto
provideoptimaluse.
OnlyaqualifiedcontractorshouldinstallthePro‐LIFTWMH.Ifyoudonotunderstandanyofthe
assemblyinstructions,pleasecontactyourlocalre‐sellerorvisitwww.proliftstand.com.
IMPROPERINSTALLATIONCANCAUSEDAMAGETOYOURPro‐LIFTANDLEADTOSERIOUSPHYSICAL
INJURY.JOROManufacturingcannottakeanyresponsibilityfordamageorinjuryresultingfrom
improperinstallation.
DonotoperatePro‐LIFTWMHifthereareanyobstructionsbeloworabovethe
board.Doingsomaycauseunitmalfunctionorleadtoseriousphysicalinjury.
ThesuppliedmountinghardwareisforuseonthePro‐LIFTstandsonly.Ifyouencounteranyproblems
orinsufficienthardwareduringinstallation,pleasecontactyourlocalre‐seller.

M6x8mm SILVER Button Head
4x
ProLift WM Hybrid - WMHW ASSY Instructions : 0.003
JORO Button Head
4x
WB Fastener Kit
(ONLY available with WMHW Models)
LCD Mount Fastener Kit
(ONLY available with WMHL Models)
Note: Parts may not be exactly as shown and not to scale
WMH Main Frame Kit
JORO Button Head
16x
M6x8mm SILVER Button Head
4x
5/16x3/4" SILVER Button Head
4x
5/16" Washer
4x
5/32" Allen (Hex) Key
1x
M6x8mm SILVER Button Head
8x
Board Backer Support
4x
Wire Mgmt Molding
4x
M6 Hex Nut
4x
5/16 Hex Nut
4x
3/16" Allen (Hex) Key
1x
18x
M6 x 20mm Socket Cap Screw Low Profile
5/32" Allen (Hex) Key
1x
8x
M6 x 20mm Socket Cap Screw Low Profile
Machine Screw Insulator
6x
Nylon Washer
6x
5/32" Allen (Hex) Key
1x
1/4" Washer
4x
#12 x 2" Slotted Washer Head Self Tapping Screw
12x
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

For ease of installation, do this step while Pro-LIFT Wall Mount Hybrid is lying down
BE AWARE the mounting position of the Pencil Tray Adapter is dependant on projector/white
board combination
Be sure to use at least two fasteners per Pencil Tray Adapter
Be sure to NOT over tighten
ProLift WM Hybrid - WMHW ASSY Instructions : 0.003
M6 x 20mm Socket Cap Screw
Low Profile
Pro-LIFT WM Pencil Tray Adapter
Nylon Washer
Machine Screw Insulator
1
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

ProLift WM Hybrid - WMHW ASSY Instructions : 0.003
Be sure to fasten Sacrificial Surface to at least three joists
Sacrificial Surface
(recommended
3/4" thick)
Recommended42
Recommended
6
Recommended
36
Min.
Min.
13.75 Recommended
2
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

Mark out the two screw locations to hang the Wall Mount Hybrid
Pre-drill pilot holes at the two locations
Be sure both points are horizontal and level
ProLift WM Hybrid - WMHW ASSY Instructions : 0.003
Slotted Hex Washer Head Screw
Slotted Hex Washer Head Screw
(recommended for8'ceiling)
54
30
Slotted Hex Washer Head Screw
Fasten the two Slotted Hex Washer Head Screws in the pre-drilled holes
Allow3/8"Min.distance
fromsacrificial surfaceto
hangWall MountHybrid
3
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

ProLift WM Hybrid - WMHW ASSY Instructions : 0.003
Hang the Wall Mount Hybrid on the two screws
Be sure Wall Mount Hybrid is securely fastened to wall by tightening all screws
Slotted Hex Washer Head Screw
Add the remaining Slotted Hex Washer Head Screws
(3 per either side of Wall Mount Hybrid is recommended)
4
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

WB Hanger
M6x8mm SILVER Button Head
Be sure to use the M6x8mm SILVER Button Head screws provided
Mount the WB Hanger
Be sure to NOT over tighten
BE AWARE the mounting position of the WB Hanger is dependant on projector/white
board combination
ProLift WM Hybrid - WMHW ASSY Instructions : 0.003
5
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

M6 x 20mm Socket Cap Screw
Low Profile
Be sure to use the M6 x 20mm Socket Cap Screws provided
ProLift WM Hybrid - WMHW ASSY Instructions : 0.003
Mount the Turret Head
Be sure to NOT over tighten
6
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

JORO Button Head Screw
Wall Mount Hybrid Control Panel
Be sure to use the JORO Button Head Screws provided
CTRLTUBE1020
For WMHW Systems
Mount the Wall Mount Hybrid Control Panel
Be sure to NOT over tighten
Mount the Wall Mount Hybrid OD Control Panel
Be sure to plug in the ODS plug
Be sure to NOT over tighten
ProLift WM Hybrid - WMHW ASSY Instructions : 0.003
JORO Button Head Screw
Wall Mount Hybrid Control Panel
Be sure to use the JORO Button Head Screws provided
CTRLTUBE1020
ODS Plug
For WMHW-OD Systems
(if ordered with your product)
7
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

ProLift WM Hybrid - WMHW ASSY Instructions : 0.003
Be sure to NOT over tighten
Mounting position dependant on white board width
Mount the CTRLTUBE1020
CTRLTUBE1020
M6x8mm SILVER Button Head
CTRLTUBE1020
Be sure to use the M6x8mm SILVER Button Head Screws provided
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com
8

Mounting patterns for tested projectors
Match holes in the diagram to projection system being used
Be sure to NOT over tighten
ProLift WM Hybrid - WMHW ASSY Instructions : 0.003
Fasten projector to the corresponding holes using the
JORO Button Head Screws supplied
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com
9

ProLift WM Hybrid - WMHW ASSY Instructions : 0.003
Remove the backing from the
double sided tape and attach to
outer edge of upright
JORO recommends attaching the
Board Backer Supports supplied
Mount the white board
Use the holes which correspond to manufacturers
recommended projector to image distance
Be sure to NOT over tighten
Note, there are drilled/tapped holes on the frame
upright, if lowering the board is required
Fasten using the JORO Button Head screws supplied
Mount the Wire Mgmt Molding
JORO recommends attaching the
Wire Mgmt Moldings supplied
Remove the backing from the double
sided tape and attach to side of frame
upright
Wire Mgmt Molding
Mount the Board Backer Support
Board Backer Support
Lower
drilled/tapped
holes
JORO Button Head
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com
10

To Heighten
To Lower
Adjusting Turret Head IF NECESSARY
ProLift WM Hybrid - WMHW ASSY Instructions : 0.003
JORO Button Head
M6x6mm Button Head
Adjust the M6x6mm Button Head Screws accordingly
JORO Button Head
M6x6mm Button Head
Loosen JORO Button Head Screws 1 turn each side
Be sure re-tighten JORO Button Head Screws - DO NOT OVER TIGHTEN!
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

11



12














Page Left Blank On Purpose

Be sure to fasten Sacrificial Surface to at least three joists
Sacrificial Surface
(recommended
3/4" thick)
Recommended42
Recommended
6
Recommended
36
Min.
Min.
13.75 Recommended
ProLift WM Hybrid - WMHL ASSY Instructions : 0.003
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com
1

ProLift WM Hybrid - WMHL ASSY Instructions : 0.003
Slotted Hex Washer Head Screw
Slotted Hex Washer Head Screw
(recommended for 8' ceiling)
54
30
Mark out the two screw locations to hang the Wall Mount Hybrid
Pre-drill pilot holes at the two locations
Be sure both points are horizontal and level
Slotted Hex Washer Head Screw
Fasten the two Slotted Hex Washer Head Screws in the pre-drilled holes
Allow3/8"Min.distance
fromsacrificial surfaceto
hangWall MountHybrid
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com
2