Pro-Lift G4U-LCD User manual





ThankyouforpurchasingaPro‐LIFTG4U‐LCDorG4U‐LED.ThemobilePro‐LIFTproductlineisdesigned
toenhanceyourLED/LCDscreen.Pleasefollowallassemblyinstructionscorrectlytoprovideoptimal
use.
OnlyaqualifiedcontractorshouldinstallthePro‐LIFTG4U‐LCD.Ifyoudonotunderstandanyofthe
assemblyinstructions,pleasecontactyourlocalre‐sellerorvisitwww.proliftstand.com.
IMPROPERINSTALLATIONCANCAUSEDAMAGETOYOURPro‐LIFTANDLEADTOSERIOUSPHYSICAL
INJURY.JOROManufacturingcannottakeanyresponsibilityfordamageorinjuryresultingfrom
improperinstallation.
ThesuppliedmountinghardwareisforuseonthePro‐LIFTstandsonly.Ifyouencounteranyproblems
orinsufficienthardwareduringinstallation,pleasecontactyourlocalre‐seller.

Pro-LIFT G4U-LCD Assembly Sheet
 
OPEN BOX and IDENTIFY ALL KITS!!

FRONTFACE
LONGEXTENSION
FACINGFRONT
SL‐VESABrackets
G4U‐LCD Modesty
CONTROLPANEL
LEG
ACCESSORYSHELF
MODESTY
FOOT
CASTER

Pro-LIFT G4U-LCD Assembly Sheet
 

STEP 1
Install Casters
(Requires4boltspercaster)
Lockcasteroncecompleted!
Repeatabovefor4casters
BESURETONOTOVERTIGHTEN!
STEP 2
Install Foot
(Requires2boltsperfoot)
Ensurelongextensionfacingforwardandoutward.
BESURETONOTOVERTIGHTEN!


STEP 3
Install Control Panel
(Requires4bolts)
Ensurepoweroutletisfacingoutwardandcontrolboxtoinsideasperdiagram.
Oncefastened….
ConnectM1motorcabletoleg1andconnectM2motorcabletoleg2
BESURETONOTOVERTIGHTEN!
STEP 4
Install Accessory Shelf
(Requires4boltsanddowelnut‐serts)
Ensure“Pro‐LIFT”writingfacesback.
Slidedowelnut‐sertintoholeonplastic.
Alignholeondowelnut‐sertwithboltthenfastenbolttonutinsert.
BESURETONOTOVERTIGHTEN!
C
Left Foo
t

B
Right Foot
**Indicator**
V
V
ATTENTION!!
Be sure to use M6x12mm
Socket Cap SILVER.
Failure to do so will
result in malfunction to
JORO leg!
D
D
E
E

Pro-LIFT G4U-LCD Assembly Sheet
 



STEP 5
Accessory Shelf Adjustment
(2boltsanddowelnut‐sertsalreadyfastened)
Ifrequired,loosenboltsandslideaccessoryshelftocorrectposition.
BESURETONOTOVERTIGHTEN!
Formost50”to80”LCDScreensFormost23”to50”LCDScreens
STEP 6
Mounting LCD Screen to SL-VESA Brackets
(RequiresMachineScrews/ToothWashers/Washers/Spacers)
DeterminewhichmachinescrewisusedwithyourLCDscreen.PlasticspacersareprovidedandmaynotneedtobeuseddependingonthestyleofbackpanelontheLCD.
Afterlocatingthemountingholesandusingthecorrectmachinescrews,washersandspacers(ifneeded),fastentheLCDscreentotheSL‐VESAbrackets.
ENSURETHEBOLTSARETIGHTBUTDONOTOVERTIGHTEN!
E
E
Machine Screw
Plastic S
p
acer
Tooth Washer
Washer
Machine Screw
Tooth Washer
Washer
Washer
Plastic S
p
acer

Pro-LIFT G4U-LCD Assembly Sheet
 
 
STEP 7
Tilting LCD Screen
Foreaseoftilting,itisrecommendedtotilttheSL‐VESABracketspriortomounting
onthePro‐LIFTG4U‐LCD.TotilttheSL‐VESABracketspulltheplungeroutandeither
pushorpulluntilyouheretheplungerclickintopositionatthedesiredangle.
TheLCDrotatesin2.5°increments–5positiveand2.5negative
STEP 8
Mounting SL-VESA Brackets to Pro-LIFT G4U-LCD
ManeuverSL‐VESABracketsoverthePro‐LIFTG4U‐LCDmodesty‘sandlowertheSL‐
VESAbracketssotheyarerestingontopofbothmodesty’s.Onceensuringboth
bracketsareengagedwiththemodesty’sandaftercentringtheLCDscreen,tighten
thefourclampingbolts.
ENSURETHEBOLTSARETIGHTBUTDONOTOVERTIGHTEN!




G4U-LCD Modesty
SL-VESA Bracket
Clamping Bolt
-2.5°5°