Pro2 AVS-5800 C User manual

Model: AVS-5800 C
5.8 GHz Audio/Video Sender
1. Package Content………………………………………………1
2. Panel Control and Function……...……………………………2
3. Setup Guide…………………..………………….……………4
4. Orient Transmitter/Receiver for optimal performance…….….5
5. Important Safety Information….……………………..…..……6
6. Specifications………………………………………………….7
Check to make sure that all units shown as below are enclosed. If something
missed, please contact your dealer.
1. 5.8GHz Transmitter x 1 2. 5.8GHz Receiver x 1
UHF: 433.92MHz
3. IR Mouse x 1 / fasten strips x 2
4. Accessories
1. Package Content
1
Contents
408-000497-01

Australia Standard:
(1) Power Adapters (230V) x 2 (2) RCA cable x 2
USA Standard
(1) Power Adapters (120V) x 2 (2) RCA Cable x 2
1. – Channel selection switch to find optimal
reception, the transmitter and
receiver must to be Configured as the same channel.
2A –Remote control LED sends IR rays, to remotely control the source AV
equipment.
2B –Remote control LED receives IR rays from remote controller.
3A – Directional 5.8GHz A/V antenna sends A/V signal from source
equipment.
3B – Directional 5.8GHz A/V antenna receives audio and video signal.
4 – Power on/off switch.
5 – DC power input, connect to power supply. (9v).
6 – IR Mouse output, to remotely control source AV equipment.
7A –Video Jack, (yellow), input from source AV equipment.
7B –Video Jack, (yellow), output to TV.
8A –Audio Jack, Right (red), input from source AV equipment.
8B –Audio Jack, Right (red), output to TV.
9A –Audio Jack, Left (white), input from source AV equipment.
9B –Audio Jack, Left (white), output to TV.
10 –Power LED.
2. Panel Control and Function
3
2
1
42A
10
5
7A
8A
9A
6
3A
1
2B
10
5
7B
8B
9B
3B
4
5.8GHz Transmitter
5.8GHz Receiver

To enjoy a life of wireless video and audio, just connect the transmitter to any
A/V source you like and connect the receiver to a TV, monitor or speaker in
another location.
□ Transmitter
□ Receiver
For optimal performance, both the audio/video and remote control antennas
should be carefully oriented as described below. For maximum transmitting
range, try to minimize obstacles (e.g. your TV or other electronics, large
furniture) where between the transmitter and receiver.
Orients the 5.8GHzA/VAntennas
NOTE: Make sure the ON/OFF switch is in the 「OFF」position before connection
3. Setup Guide
1. Connect one end of the RCA cable (or
scart cable) to the audio and video jacks,
and connect the other end to a source
device via its “AV output”.
2. Connect the DC plug of the adapter to the
DC jack, and connect the power supply to
an outlet.
3. Fix IR mouse next to or in front of IR
sensor of source device, or alternatively
have transmitter facing directly toward the
source device.
4. Orient Transmitter/Receiver for optimal performance
The system delivers high-quality audio and
video by using directional antennas, which must
be oriented in the best ways. The antennas are
designed to be able to vertically and horizontally
pivot and rotate in almost any direction.
In most situations, the flat-pitted face of the antennas on both the transmitter
and receiver should be facing one another and perpendicular (at a right angle)
to an imaginary line drawn between the two units. Three examples are shown
as Fig-1, Fig-2 and Fig-3. Since all homes are different, for optimal reception,
additional slight pivots or rotations may be necessary. If the transmitter and
receiver are less than 10 feet apart, suggest that the antennas are lying on their
casings since the distance is so short.
1Connect one end of the RCA cable (or
scart cable) to the audio and video jacks
and connect the other end to a TV (or
monitor, speakers) via its “AV input”.
2Connect the DC plug of the adapter to
the DC jack, and connect the power
supply to an outlet.
4 5
3. Keep the IR window oriented toward front when using your source device remote
controller.
LED
AUDIO
LEFT
AUDIO
RIGHT VIDEO
AUDIO
LEFT
AUDIO
RIGHT
VIDEO
5.8GHz Antenna
5.8GHz Antenna
Receiver
Transmitter Fig-1
Pitted
Side
Pitted
Side
5.8GHz Antenna
5.8GHz Antenna
Transmitter
Receiver
Fig-2
Transmitter
Receiver
5.8GHz Antenna
5.8GHz Antenna
Fig-3

To prevent fire or shock hazard, do not expose this product to rain and
moisture. For example: do not use near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or nearby a swimming pool. To avoid electric
shock, do not take apart this product, provided as an accessory. This product
should be operated only under power supply. Do not overload wall outlets and
extension outlets as this can result in the risk of fire or electric shock.
OPERATING FREQUENCY 5.725Ghz-5.875Ghz 4 User Selectable
Channels
RADIATED POWER 50mV@3m
RANGE(LINE-OF-SIGHT) Up to 300 Feet line of sight
ANTENNA TYPE Fixed Directional Patch
RECEIVER SENSITIVITY -84dBm
VIDEO FORMAT NTSC or PAL
VIDEO CONNECTOR RCA Female @ 75 OHMS 1 Volt p-p
AUDIO CONNECTOR RCA Female Stereo Left & Right @
600 OHMS 1 Volt p-p
TEMPERATURE RANGE 0°C to 50°C
OPEARATING VOLTAGE 9VDC – Adapter
CURRENT CONSUMPTION Transmitter 250mA@9VDC
Receiver 350mA@9VDC
DIMENSIONS 130mm x123mm x55mm
WEIGHT 0.3kg each
FCC/CE APPROVED Yes
6
5. Important Safety Information
□
□□
□ NOTE:
This equipment has been tested and found to comply with the limits regulated
by FCC and CE. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction, may cause harmful interference
to radio communications. The change or modifications no expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment. To comply with the FCC RF exposure compliance
requirements, no change to the antenna or the device is permitted. Any
change to the antenna or the device could result in the device exceeding the
RF exposure requirements and void user’s authority to operate the device.
6. Specifications
7