Procom 21VU User manual

PRO
ception
INSTALLATION INSTRUCTIONS
These masthead and general-purpose passive products are used for combining or splitting
signals in the VHF/FM, UHF and satellite IF frequenc bands with a minimum of insertion
loss. The units are full -screened and are eas to install, both indoors and outdoors. The use
of F connectors allows their use with a wide range of cable sizes.
Features
nLow in-band insertion loss.
nHigh rejection of unwanted bands.
nIdeal for both digital and analogue applications.
nPower-pass to the higher or highest frequenc band input.
nRobust diecast housings, suitable for outdoor (masthead) and indoor use.
Application examples
proCOM21VU is a two-band passive combiner/splitter (diplexer) for combining or splitting
signals in Band II (VHF/FM) and Bands IV-V (UHF). T pical applications include combining
signals from VHF/FM and UHF antennas onto a single downlead cable Fig. 1 or splitting
a combined feed from a distribution amplifier or s stem to feed separate outlets Fig. 2. This
unit will pass line-power between the common and UHF ports, allowing a masthead
preamplifier to be used on the UHF antenna if necessar Fig. 3.
proCOM31VUS is a 3-band passive combiner/splitter (triplexer) for combining or splitting
signals in Band II (VHF/FM), Bands IV-V (UHF) and the satellite IF band (SAT). The ver high
rejection on the SAT port in the FM and UHF bands allows this unit to be used to combine
the output of a satellite LNB with VHF and UHF terrestrial antennas Fig. 4. High isolation
is required in this application to prevent wideband amplified noise present on the output
of the LNB from degrading the VHF and UHF signals. The proCOM31VUS passes line-power
between the common and SAT ports, allowing LNB power and 22 kHz tone or DiSEqC
controls to function normall .
PD2011-9015-01
Page 4 Page 1
proCOM
Band-Selective Combiner/Splitters
PROception
Proception Limited,
177-187 Rutland Road
SHEFFIELD
S3 9PT
United Kingdom
We : http://www.proception.co.uk/
e-mail: [email protected]
Performance data given are typical unless otherwise stated. Proception Limited reserves the
right to change product designs and specifications without prior notice.
2-Year Guarantee
This guarantee covers failure of your PROception product resulting from manufacturing
defect ithin a period of 2 years from the date of supply to the end-user.
This guarantee does not cover damage to the product caused by abuse, tampering, defective
installation or natural causes such as lightning discharge. Repair or attempted repair, other
than by the manufacturer, ill render this guarantee void.
This guarantee does not affect a consumers statutory rights. Fig.1 combining antennas
proCOM21VU
proOUT12C outlet
Notes
1. £ 2.7 dB in band edge region 780 .. 862 MHz
2. £ 5.5 dB in band edge region 950 .. 1100 MHz
3. ³ 23 dB in band edge region 950 .. 1100 MHz
Technical data proCOM amily
UV12MOCorpSUV13MOCorp
tropMF/FHVtropFHUtropMF/FHVtropFHUtropTAS
egnarycneuqerfgnitarepOzHM801..5.78zHM268..074zHM801..5.78zHM268..074zHM0032..059
ssolnoitresn £Bd0.1 £Bd0.1 £Bd2.1 £Bd8.1
1
£Bd5.2
2
dnabMFninoitalos
³Bd03 ³Bd03 ³Bd05
dnabFHUninoitalos ³Bd03 ³Bd03 ³Bd84
dnabTASninoitalos ³Bd04 ³Bd63
3
tropnommocmorfssaprewop-eniLoNseYoNoNseY
sgnitarssaprewop-eniL.xamAm004ta.xamV02
epytrotcennoclangiS)42-96106
CE(F-epyT
egnarerutarepmetgnitarepOC°05+..02-
dradnatsCME)AssalC(1002:2-38005NESB
VHF/FM UHF

PROception
PRO
ception
PRO
ception
PRO
ception
PROception
Page 3Page 2
Signal connections
To preserve RF screening integrit the signal connections to the amplifier should be made
using good qualit coaxial cable and connectors. This is particularl important with DTT to
minimise the ingress of impulsive electrical interference. The use of cable benchmarked
under the CAI scheme is recommended.
Crimp F connectors, used in accordance with the manufacturers instructions, will give the
best results. The importance of achieving sound braid connections cannot be over-stressed.
System earth bonding
Earth bonding terminals are provided on the amplifier castings for use where necessar .
Distribution s stems suppl ing signals to more than one household should compl with the
safet requirements of BS EN 50083-1. This effectivel requires the s stem to be earth
bonded. (The use of isolated outlet plates is no longer recommended since the compromise
screening integrit and allow ingress of interference.)
Fixing
Methods for mounting the amplifier are illustrated in Figs. 5 to 7. The cable tie fixing is
intended to support the weight of the amplifier onl . Cables should be taped to the mast at
intervals of approximatel 400 mm to ensure that their weight is adequatel supported.
Being full screened, these amplifiers will not be affected b proximit to antennas. However
clearance of not less than 300 mm from the nearest part of an antenna should be observed
to avoid degrading the antennas performance.
Fig.5 cable tie fixing Fig.6 fixing to flat surface
Fig.7 Fixing the amplifier
module directly (indoor
application only, discard
mouldings).
Earth terminal
(see text).
Fig.4 combining antennas and LNB
proCOM31VUS
proOUT13 outlet
Fig.2 splitting a distribution s stem feed to separate outlets
proCOM21VU
proOUT11C outlets
amplifier proAMP24
Fig.3 using a UHF preamplifier
proCOM21VU
proOUT12C outlet
power unit
proPSU11F
preamplifier
proMHD11L
Note: a preamplifier cannot be powered via the proCOM31VUS since there is no line-power
pass to the UHF port.
VHF/FM
UHF
UHF
VHF
VHF/FM UHF
VHF/FMUHF LNB
This manual suits for next models
2
Popular Cables And Connectors manuals by other brands

Pedigree Technologies
Pedigree Technologies OneView TTU2830 installation manual

Radiall
Radiall SMP LOCK Series Technical data sheet

Mennekes
Mennekes AM-TITE PLUG Series Wiring instructions

Conrad
Conrad 91 79 12 operating instructions

PowerBox Systems
PowerBox Systems P2-SERVOBRIDGE instruction manual

Solwise
Solwise HDF-200 quick start guide