PRODIS CL20 User manual

CL20
ICE MAKER
ICE MAKER
CL200718UM Rev 1.3
USER MANUAL

PART I - WARNINGS
PART II - INSTALLATION
PART III - OPERATING INSTRUCTIONS
PART IV - MAINTENANCE AND CLEANING
PART V - TROUBLE SHOOTING
TABLE OF CONTENTS
CL200718UM Rev 1.3

PART I
01. PROPER INSTALLATION, USE AND
MAINTENANCE OF THIS MACHINE ARE ALL
IMPORTANT FOR MAINTAINING PRODUCTION
AND USER SAFETY. IN ORDER TO REDUCE
THE FAILURE RATE PLEASE READ THESE
INSTRUCTIONS CAREFULLY. IMPROPER USE
COULD RESULT IN EQUIPMENT DAMAGE,
PERSONAL INJURY OR EVEN DEATH.
02. DO NOT USE THE ICE MAKER IF YOU
HAVE NOT BEEN PROPERLY TRAINED.
03. DO NOT LET CHILDREN PLAY WITH THE ICE
MAKER OR ITS PACKAGING MATERIALS.
04. AT LEAST TWO PEOPLE ARE REQUIRED TO LIFT
THE ICE MAKER OR IT IS RECOMMENDED THAT A
LIFTING DEVICE IS USED TO AVOID INJURY.
05. A QUALIFIED ENGINEER MUST PERFORM
THE INSTALLATION AND ONGOING
MAINTENANCE OF THE ICE MAKER.
06. WHEN OPERATING ALL PROCEDURES
MUST BE FOLLOWED IN ACCORDANCE WITH
THESE INSTRUCTIONS TO ENSURE NO DAMAGE
OCCURS TO THE REFRIGERATION SYSTEM.
07. DO NOT OPERATE THE ICE MAKER IF
THERE ARE ANY UNAUTHORISED CHANGES
TO THE ORIGINAL MANUFACTURERS
SPECIFICATIONS OR IF THE MACHINE HAS
BEEN MISUSED, ABUSED OR NEGLECTED.
08. ENSURE THE ICE MAKERS FRONT
PANEL AND COVER ARE IN PLACE
BEFORE TURNING THE MACHINE ON.
09. DO NOT COVER THE ICE MAKERS VENTS,
THERE MUST BE A MINIMUM CLEARANCE
OF 150MM AROUND THE ICE MAKER AT
ALL TIMES DURING OPERATION.
10. DO NOT STORE FLAMMABLE GASES OR
LIQUIDS IN OR NEAR TO THE ICE MAKER.
11. DO NOT USE HIGH-PRESSURE
WATER CLEANING DEVICES TO
CLEAN THE ICE MAKER
12. IT IS THE USERS RESPONSIBILITY TO TAKE
APPROPRIATE MEASURES TO ENSURE THE SAFETY
OF STAFF OPERATING THE ICE MAKER.
13. IT IS THE USERS RESPONSIBILITY TO
ENSURE THE ONGOING MAINTENANCE
OF THE ICE MAKER IS COMPLETED IN
ACCORDANCE WITH THE MANUFACTURERS
INSTRUCTIONS LAID OUT IN THIS MANUAL.
14. TO PREVENT ACCIDENTAL INJURIES KEEP THE
AREA SURROUNDING THE ICE MAKER CLEAN AND
TIDY AND FREE FROM OBSTRUCTIONS.
CL200718UM Rev 1.3
1

PART II
01. THIS MANUAL IS AN INTEGRAL PART
OF THE ICE MAKER AND SHOULD BE KEPT
AND PRESERVED BY THE USER FOR FUTURE
REFERENCE. PLEASE READ THE INSTRUCTIONS
CAREFULLY FOR THE CORRECT INSTALLATION
METHOD, SAFETY WARNINGS AND MAINTENANCE
INFORMATION FOR THIS ICE MAKER.
02. THIS ICE MAKER IS DESIGNED FOR
COMMERCIAL USE AND SHOULD BE USED
FOR THE PURPOSE FOR WHICH IT HAS BEEN
EXPRESSLY DESIGNED. ANY OTHER USE SHOULD
BE CONSIDERED IMPROPER AND THEREFORE
DANGEROUS. THE MANUFACTURER WILL
NOT BE LIABLE OR RESPONSIBLE FOR ANY
DAMAGE CAUSED BY IMPROPER, INCORRECT OR
UNREASONABLE USE.
iv. REMOVE THE PROTECTIVE PLASTIC FILM
FROM THE EXTERIOR BEFORE INSTALLATION. IF
THE ICEMAKER HAS BEEN EXPOSED TO SUN OR
HEAT ALLOW THE ICE MAKER TO COOL DOWN
BEFORE REMOVING THE PROTECTIVE FILM.
iv. REMOVE THE ACCESSORY PACK AND CHECK
THE CONTENTS, IT SHOULD CONTAIN
1 x INLET WATER HOSE
1 x ICE SCOOP
1 x DRAIN HOSE
1 x INSTRUCTION MANUAL
IMPORTANT
WARNING
THE INSTALLATION OF THIS ICE MAKER MUST
BE CARRIED OUT BY QUALIFIED PERSONNEL IN
ACCORDANCE WITH CURRENT REGULATIONS
AND AS PER THE MANUFACTURERS
INSTRUCTIONS. FAILURETO CORRECTLY INSTALL
THIS ICE MAKER COULD RESULT IN DAMAGE OR
INJURY AND WILL VOID THE WARRANTY.
INSTALLATION
01. UNPACKING
WARNING
KEEP ALL PACKAGING MATERIALS INCLUDING
BOXES, PLASTIC BAGS AND POLYTHENE OUT OF
REACH OF CHILDREN
IMPORTANT
i. REMOVE ALL SHIPPING MATERIALS, TAPE
AND PACKAGING FROM THE BOTH OUTSIDE
AND INSIDE THE ICE MAKER. IF PACKAGING
MATERIAL IS LEFT INSIDE THE ICE MAKER IT
WILL NOT FUNCTION CORRECTLY
ii. AFTER REMOVING THE PACKAGING MAKE
SURE THE ICE MAKER IS IN GOOD CONDITION.
IF IN DOUBT PLEASE DO NOT INSTALL OR USE
THE ICE MAKER AND CONTACT YOUR SUPPLIER
IMMEDIATELY.
iii. REMOVE THE SHIPPING TAPE WHICH IS
HOLDING THE DOOR AND FRONT PANEL
WARNING
THIS ICE MAKER IS NOT INTENDED
FOR OUTDOOR USE. NORMAL OPERATING
TEMPERATURES FOR THIS ICE MAKER ARE
BETWEEN 10°C AND 32°C. USE OF THIS
ICE MAKER OUTSIDE OF THE DEFINED
OPERATING PARAMETERS WILL AFFECT
PRODUCTION AND MAY DAMAGE THE UNIT.
01. ENSURE THERE IS A FREE FLOW OF CLEAN
AIR AVAILABLE ALL AROUND THE ICE MAKER.
02. THE ICE MAKER SHOULD NOT BE LOCATED
CLOSE TO A HEAT SOURCE (RADIATOR, STOVE
OR HEATER) OR EXPOSED TO DIRECT SUNLIGHT.
03. THE INSTALLATION LOCATION SHOULD
BE FIRM AND LEVEL AND ABLE TO SUPPORT
THE FULL WEIGHT OF THE ICE MAKER
WHEN LOADED WITH ICE AND WATER.
04. ALLOW AT LEAST 150MM CLEARANCE
AT THE REAR, BOTH SIDES AND TOP
OF THE ICE MAKER FOR PROPER AIR
CIRCULATION AND EASE OF MAINTENANCE.
05. THIS ICE MAKER IS NOT SUITABLE
FOR INSTALLATION IN AREAS WHERE
WATER IS FREE FLOWING OR HIGH
PRESSURE WATER JETS ARE USED
06. IF THE AMBIENT TEMPERATURE DROPS
BELOW 10°C THE UNIT SHOULD NOT BE USED.
IF THE AMBIENT TEMPERATURE DROPS BELOW
10°C WATER SHOULD BE DRAINED OUT OF THE
UNIT AND SUPPLY HOSES TO PREVENT DAMAGE
IF THE WATER FREEZES.
LOCATION
CL200718UM Rev 1.3 2

01. CARE SHOULD BE TAKEN TO ENSURE THE
ICE MAKER IS PERFECTLY LEVEL FOR CORRECT
OPERATION. THE UNIT HAS 4 ADJUSTABLE FEET
ON THE BOTTOM FOR LEVELLING. A SPIRIT
LEVEL SHOULD BE USED TO CHECK THE UNIT IS
PERFECTLY LEVEL, IF THE UNIT IS NOT LEVEL ICE
PRODUCTION WILL BE AFFECTED.
LEVELLING THE ICE MAKER
WARNING
ALL WIRING AND ELECTRICAL CONNECTION
MUST CONFIRM TO NATIONAL REGULATIONS.
ALL ELECTRICAL CONNECTIONS MUST BE
UNDERTAKEN BY A COMPETENT ENGINEER OR A
QUALIFIED ELECTRICIAN.
ELECTRICAL CONNECTION
01. THIS ICE MAKER MUST BE PLUGGED IN
TO AN INDEPENDENT POWER SOURCE OR
AN ELECTRICAL SOCKET OF VOLTAGE AND
FREQUENCY SPECIFIED. ELECTRICAL RATING
INFORMATION CAN BE FOUND ON THE DATA
PLATE OF THE ICE MAKER.
02. THIS ICE MAKER MUST BE CONNECTED TO
AN INDEPENDENT CIRCUIT BREAKER OR FUSE.
03. DUE TO POTENTIAL SAFETY HAZARDS THIS
ICE MAKER IS NOT RECOMMENDED FOR USE
WITH AN EXTENSION LEAD
PART II
ELECTRICAL SPECIFICATION
MODEL VOLTAGE TOTAL POWER CURRENT
CL20 230V/50Hz 155w 0.9 amps
WARNING
IF THE POWER SUPPLY CABLE IS DAMAGED,
DO NOT INSTALL OR OPERATE THE MACHINE
UNTIL THE CABLE HAS BEEN REPLACED BY
AN AUTHORISED SERVICE PARTNER OR A
QUALIFIED ENGINEER.
WARNING
PLEASE TAKE PROTECTIVE MEASURES WHEN
THE AMBIENT TEMPERATURE DROPS BELOW
10°C.
WARNING
ALL ELECTRICAL CONNECTIONS MUST
CONFORM TO LOCAL REGULATIONS AND BE
CARRIED OUT BY A QUALIFIED ENGINEER
WE RECOMMEND INSTALLATION OF AN
INLINE WATER FILTER TO THIS ICE MAKER.
THIS WILL REDUCE LIMESCALE BUILD UP,
IMPROVE EFFICIENCY, AND EXTEND THE
OVERALL LIFESPAN OF THE UNIT. A WATER
FILTER WILL ALSO REMOVE IMPURITIES AND
CREATE A CLEARER, BETTER TASTING ICE CUBE.
01. WATER SUPPLY PRESSURE SHOULD
BE BETWEEN 1.4BAR AND 5.5BAR. IF THE
PRESSURE EXCEEDS 5.5 BAR A PRESSURE
REDUCING VALVE MUST BE USED.
FAULTS DUE TO LOW OR HIGH WATER PRESSURE
ARE NOT COVERED UNDER WARRANTY.
02. THE DRAIN CONNECTION
SHOULD BE INSTALLED INTO AN
OPEN TRAPPED DRAIN. (SEE FIG.1).
03. THE ICE MAKER DRAIN IS GRAVITY FLOW,
THE ICE MAKER NEEDS TO BE INSTALLED ABOVE
THE HEIGHT OF MAIN DRAIN TO ALLOW FOR EASY
DRAINING
WATER SUPPLY AND DRAIN CONNECTION
FIG.1
04. ATTACH ONE END OF THE WATER INLET
HOSE TO THE REAR OF THE MACHINE AND
ATTACH THE OTHER END OF THE HOSE TO THE
MAINS WATER CONNECTION. IT IS ADVISABLE TO
HAVE A STOP VALVE CLOSE TO THE ICE MAKER.
CL200718UM Rev 1.3
3

05. PUSH THE FLEXIBLE DRAIN HOSE ON THE
DRAIN SPIGOT AT THE REAR OF THE MACHINE
AND SECURE WITH THE CLIP PROVIDED. THE
DRAIN PIPE CAN BE CUT TO LENGTH TO ALLOW
THE DRAIN CONNECTION TO HAVE A SLIGHT FALL
IF NECESSARY
ALL ICE MACHINES HAVE BEEN FACTORY PRESET
BEFORE SHIPMENT. ADJUSTMENTS TO THE
PROGRAM OR SETTINGS ARE NOT REQUIRED
FOR A NEW ICE MAKER INSTALLATION. IN
ORDER TO ENSURE NORMAL OPERATION OF THE
ICEMAKER PLEASE REFER TO PART III OF THIS
MANUAL. ALWAYS REMEMBER THAT CHECKING
AND MONITORING OF THE ICE MAKER IS THE
RESPONSIBILITY OF THE OPERATOR.
PRE-INSTALLATION CHECK LIST
IS THE ICE MAKER INSTALLED ON A
HORIZONTAL AND LEVEL SURFACE?
HAS THE ICE MAKER BEEN LEVELLED USING
THE ADJUSTABLE FEET?
ARE THE WATER AND DRAIN PIPES
CONNECTED SECURELY WITHOUT LEAKS?
HAS ALL OF THE INNER AND OUTER
PACKAGING BEEN REMOVED FROM THE ICE
MAKER?
IS THE ICE MAKER CONNECTED TO A
SUFFICIENT AND SUITABLE POWER SUPPLY?
IS THERE PROPER VENTILATION AROUND
ALL SIDES OF THE ICE MAKER?
HAS THE ICE MACHINE BEEN CLEANED
INSIDE AND OUT?
IS THE MACHINE CORRECTLY EARTHED?
IS THE WATER TO THE ICE MAKER TURNED
ON?
IS THE POWER TO THE MACHINE SWITCHED
ON?
IS THE ICE MACHINE LOCATED IN A ROOM
WITH AN AMBIENT TEMPERATURE BETWEEN
10°C AND 32°C?
ISTHE INLETWATERTEMPERATURE BETWEEN
7°C AND 20°C?
IS THE WATER PRESSURE BETWEEN 1.4 AND
5.5 BAR?
HAVE ALL USERS BEEN FULLY TRAINED IN
THE OPERATION OF THE ICE MAKER?
CL200718UM Rev 1.3
PART II
4

PART III
OPERATING INSTRUCTIONS
WARNING
AFTER TURNING OFF YOUR ICE MAKER YOU
MUST WAIT AT LEAST 3 MINUTES BEFORE
RESTARTING TO AVOID DAMAGE TO THE
COMPRESSOR
YOUR ICE MAKER FEATURES A TOUCH CONTROL
DISPLAY. TO OPERATE THE CONTROLS LIGHTLY
TOUCH THE PANEL WITH YOUR FINGER TIP. THE
CONTROL PANEL ALSO FEATURES AN EASY TO
READ DISPLAY WHICH INFORMS YOU OF THE
STATUS OF THE MACHINE AT ALL TIMES.
DO NOT USE A POINTED OR SHARP OBJECT SUCH
AS A PEN TO OPERATE THE TOUCH PANEL AS THIS
CANRESULT INDAMAGETOTHECONTROLSWHICH
WOULD NOT BE COVERED UNDER WARRANTY.
DIGITAL DISPLAY
THE DIGITAL DISPLAY SHOWS THE AMBIENT
TEMPERATURE, ICE MAKING TIME, CLEANING
CYCLE COUNTDOWN TIMER AND DELAY ON-
TIMER FOR THE ICE MAKER DEPENDING ON THE
MODE SELECTED.
THERE ARE 5 ILLUMINATED LED INDICATORS
WHICH SHOW THE ICE MAKER STATUS
RUNNING
ICE FULL
ERROR
TIMER
CLEANING
THERE ARE 5 CONTROL BUTTONS
POWER
CLEANING
TIMING
UP
DOWN
PLEASE REFER TO TABLE 1 FOR A FULL LIST OF
ERROR CODES AND MEANINGS.
ICE PRODUCTION
TO START ICE PRODUCTION PRESS THE ON/
OFF POWER BUTTON. THE POWER LED WILL
ILLUMINATE GREEN AND THE AMBIENT ROOM
TEMPERATURE (°C) WILL BE DISPLAYED IN THE
DIGITAL DISPLAY.
THE COMPRESSOR AND FAN MOTOR WILL THEN
START, AFTER 30 SECONDS THE PUMP WILL BEGIN
TO DISTRIBUTE WATER ACROSS THE EVAPORATOR
AND “00” WILL BE DISPLAYED ON THE DIGITAL
DISPLAY. WHEN THE EVAPORATOR REACHES -5°C
THE ICE MAKER PRODUCTION TIMER WILL START,
THE DIGITAL DISPLAY WILL INCREASE IN 1 MINUTE
INTERVALS UNTIL THE DESIGNATED ICE CYCLE
TIME IS REACHED.
ONCE THE ICE PRODUCTION CYCLE TIME HAS
COMPLETED THE MACHINE WILL SWITCH INTO
HARVEST MODE, THE WATER PUMP WILL STOP
AND THE HOT GAS BYPASS VALVE WILL ENERGISE
TO RELEASE THE ICE FROM THE EVAPORATOR. THE
DIGITAL DISPLAY WILL RETURN TO “00” AND WILL
INCREASE IN 1 MINUTE INTERVALS UNTIL THE
HARVEST CYCLE IS COMPLETE.
AFTER COMPLETING THE HARVEST CYCLE THE
HOT GAS BYPASS VALVE WILL TURN OFF. IF THE
ICE STORAGE BIN IS NOT FULL THE NEXT ICE
PRODUCTION CYCLE WILL BEGIN AFTER A 6
SECOND DELAY.
NOTE: DURING THE FIRST ICE PRODUCTION CYCLE
AFTER INITIAL POWER ON OR ICE BIN FULL THE
WATER PUMP WILL WORK FOR 3 MINUTES AND
THEN SWITCH OFF FOR 6 SECONDS BEFORE
RESTARTING.
TO STOP ICE PRODUCTION PRESS THE ON/OFF
POWER BUTTON AGAIN, THE POWER LED WILL
FLASH AND THE DIGITAL DISPLAY WILL REVERT TO
DISPLAYING THE ROOM AMBIENT TEMPERATURE.
IMPORTANT: PRESSING THE ON/OFF BUTTON
DOES NOT TURN OFF POWER TO THE MACHINE.
THE MACHINE MUST BE ISOLATED FROM THE
MAINS ELECTRICITY BEFORE ANY SERVICE OR
CLEANING IS UNDERTAKEN.
CL200718UM Rev 1.3
5

ICE THICKNESS ADJUSTMENT
TO INCREASE OR DECREASE THE ICE THICKNESS
PRESS THE UP OR DOWN ARROWS WHEN THE ICE
MAKER IS IN ICE PRODUCTION OR ICE FULL MODE.
THERE ARE 5 ICE THICKNESS LEVELS, LEVEL 3 IS
THE DEFAULT FACTORY SET THICKNESS, LEVEL 5 IS
THE MAXIMUM, LEVEL 1 IS THE MINIMUM. WHEN
THE NEW THICKNESS HAS SELECTED THE DISPLAY
WILL FLASH 5TIMES ANDTHE NEW VALUE STORED.
ICE FULL
WHEN THE STORAGE BIN IS FULL THE ICE FULL
INDICATOR ILLUMINATES RED AND THE ICE MAKER
WILL STOP ICE PRODUCTION AUTOMATICALLY.
THE DIGITAL DISPLAY WILL REVERT TO DISPLAYING
THE ROOM AMBIENT TEMPERATURE.
CLEAN
TO START A CLEAN CYCLE HOLD THE CLEAN
BUTTON FOR 3 SECONDS AND RELEASE WHENTHE
CLEAN ICON IS ILLUMINATED AND 05 IS SHOWN
IN THE DIGITAL DISPLAY. THE 5 MINUTE CLEAN
CYCLE WILL START, WHEN THE CLEAN CYCLE HAS
FINISHED THE ICE MAKER WILL AUTOMATICALLY
ENTER STANDBY MODE AND THE AMBIENT ROOM
TEMPERATURE WILL BE DISPLAYED IN THE DIGITAL
DISPLAY.
NOTE: THE CLEAN CYCLE WILL ONLY RUN WHEN
THE MACHINE IS IN STANDBY MODE.
TIMER
THE ICE MAKER IS FITTED WITH ATIMER FUNCTION
WHICH ALLOWS YOU TO SET HOW LONG THE ICE
MAKER WILL RUN BEFORE ENTERING STANDBY
MODE.
TO SET THE TIMER PRESS THE TIMING BUTTON
FOR 3 SECONDS AND RELEASE WHEN THE TIMING
LED IS ILLUMINATED AND THE DIGITAL DISPLAY IS
FLASHING. USING THE UP AND DOWN ARROWS
SELECT THE NUMBER OF HOURS YOU WOULD LIKE
THE MACHINE TO RUN FOR UP TO A MAXIMUM OF
12 HOURS. ONCE THE TIMER IS SET THE DISPLAY
WILL FLASH 5 TIMES AND ENTER ICE PRODUCTION
MODE. THE ICE MAKER WILL THEN CONTINUE
TO RUN UNTIL THE TIMER EXPIRES OR THE ICE
STORAGE BIN IS FULL OF ICE.
ERROR CODE POSSIBLE CAUSE
E1 WATER SHORTAGE OR INSUFFICIENT WATER PRESSURE
E2 HARVEST CYCLE TOO LONG
E3 CONDENSER SENSOR FAULTY
E4 EVAPORATOR SENSOR FAULTY
E5 AMBIENT SENSOR FAULTY
E6 CONDENSER TEMPERATURE TOO HIGH
E7 AMBIENT TEMPERATURE TOO HIGH OR TOO LOW
E8 ICE MAKING CYCLE TOO LONG
HOW THE ICE MAKER WORKS
ICE MAKING STAGE: WHEN THE POWER ON
BUTTON IS PRESSED THE MACHINE INITIALLY
PERFORMS A RINSE TO FLUSH THE EVAPORATOR
OF ANY CONTAMINANTS. WHEN THE RINSE CYCLE
HAS FINISH THE COMPRESSOR, WATER PUMP
AND CONDENSER FAN MOTOR WILL ENERGISE
STARTING THE FREEZING CYCLE.
WATER IS THEN CIRCULATED OVER THE
EVAPORATOR SURFACE FREEZING INTO ICE CUBES.
WHEN THE PRESET THICKNESS IS REACHED AND
THE ICE IS FULLY FORMED THE FREEZING CYCLE
ENDS AND THE HARVEST CYCLE BEGINS.
FOR FURTHER ASSISTANCE WITH THE ABOVE
ERROR CODES PLEASE CONTACT YOUR
AUTHORISED SERVICE PARTNER.
WARNING
ALTHOUGH THE ICE MAKER HAS BEEN
TESTED AND CLEANED AT THE FACTORY
DIRT AND PARTICLES MAY OF ENTERED THE
SYSTEM DURING TRANSIT, UNPACKING AND
INSTALLATION. DUE TO THIS IT IS IMPORTANT
THAT ALL ICE PRODUCED DURING THE FIRST 3
HOURS IS DISCARDED.
PART III
CL200718UM Rev 1.3 6
TABLE 1
TO CANCEL THE TIMER HOLD THE TIMING BUTTON
AGAIN FOR 3 SECONDS, THE MACHINE WILL
THEN ENTER STANDBY MODE. ALTERNATIVELY
PRESSING THE POWER BUTTON WILL ALSO
CANCEL THE TIMER AND THE MACHINE WILL
ENTER ICE PRODUCTION MODE IMMEDIATELY.
NOTE: THE TIMING MODE CAN ONLY BE SELECTED
WHEN THE MACHINE IS IN STANDBY MODE.

PART IV
MAINTENANCE AND CLEANING
PERIODIC CLEANING AND PROPER MAINTENANCE
WILL EXTEND THE LIFE OF YOUR ICE MAKER,
ENSURE MAXIMUM EFFICIENCY AND DELIVER
BETTER TASTING ICE TO YOUR CUSTOMER.
WARNING
DISCONNECT THE MACHINE FROM THE MAINS
ELECTRICITY BEFORE PERFORMING ANY
CLEANING OR MAINTENANCE
WARNING
INSPECTION, DE-SCALING AND SERVICING
SHOULD ONLY BE UNDERTAKEN BY A
QUALIFIED ENGINEER
WARNING
NEVER CLEANTHE ICEMAKERWITH A PRESSURE
WASHER OR BY SPRAYING WATER
WARNING
NEVER USE ACIDIC OR ABRASIVE DETERGENTS,
THESE TYPES OF CLEANERS MAY TRANSFER
TASTE AND ODOUR TO THE MACHINE AND
THE ICE. THIS TYPE OF CLEANER MAY ALSO
DAMAGE OR DISCOLOUR THE ICE MAKER.
WARNING
NEVER CLEAN STAINLESS STEEL WITH A
BLEACH BASED CLEANER AS THIS MAY CAUSE
CORROSION ON THE STAINLESS STEEL.
EXTERIOR CLEANING
ALWAYS CLEAN THE EXTERIOR STAINLESS STEEL
PARTS OF THE ICE MAKER WITH A MICRO-FIBRE
CLOTH AND OR A SPONGE. ALWAYS CLEAN IN
THE DIRECTION OF THE GRAIN OF THE STAINLESS
STEEL.
DO NOT USE ABRASIVE OR METALLIC PRODUCTS
(WIRE WOOL) WHICH COULD SCRATCH AND
DAMAGE THE SATIN FINISH OF THE ICE MAKER
PERMANENTLY.
USING A METALLIC CLEANING PRODUCT SUCH
AS WIRE WOOL WILL DEPOSIT IRON PARTICLES
INTO THE STAINLESS STEEL WHICH COULD CAUSE
CORROSION OF THE STAINLESS STEEL FINISH.
INTERIOR CLEANING
CLEAN THE INTERIOR OF THE ICE BIN AND ALL
REMOVABLE PARTS BY WASHING THEM WITH A
SOLUTION OF LUKEWARM WATER AND A SMALL
AMOUNT OF DISH-WASHING LIQUID. RINSE AND
DRY IMMEDIATELY.
WARNING
THE ICE STORAGE BIN IS FOR STORAGE OF ICE
ONLY, NEVER STORE ANYTHING OTHER THAN
ICE IN THE STORAGE BIN AS THIS IS A HEALTH
HAZARD.
CL200718UM Rev 1.3
7
WARNING
ALWAYS TURN THE POWER OFF TO THE
MACHINE BEFORE TURNING OFF THE WATER
SUPPLY. IN THE EVENT OF A WATER SUPPLY
FAILURE PLEASE DISCONNECT THE MACHINE
FROM THE ELECTRICITY IMMEDIATELY
WARNING
NEVER TOUCH THE EVAPORATOR SURFACE
WHEN THE MACHINE IS RUNNING AS THIS MAY
CAUSE INJURY TO THE USER
WARNING
KEEP THE DOOR CLOSED AT ALL TIMES
HARVEST STAGE: DURING THE HARVEST CYCLE
THE HOT GAS BYPASS VALVE IS OPENED AND HOT
GAS IS CIRCULATED THROUGH THE EVAPORATOR.
THIS ALLOWS THE ICE CUBES TO BE RELEASED
FROM THE EVAPORATOR INTO THE STORAGE BIN.
THE NEXT FREEZING CYCLE WILL BEGIN WHEN ALL
THE CUBES HAVE FALLEN INTO THE STORAGE BIN
UNLESS THE ICE FULL MODE IS ACTIVATED BY THE
BIN FULL SENSOR.
ICE FULL STAGE: WHEN THE ICE STORAGE BIN
IS FULL THE ICE CUBES WILL NOT BE ABLE TO
FULLY RELEASE FROM THE EVAPORATOR AND
WILL HOLD THE BIN FULL SENSOR OPEN. THE ICE
MAKER WILL ENTER ICE FULL STAGE AND THE BIN
FULL LED WILL ILLUMINATE AND A BLIP SOUND
WILL BE EMITTED.
THE ICE MAKER WILL AUTOMATICALLY RESTART
THE ICE MAKING STAGE WHEN ICE IS REMOVED
FROM THE BIN AND THE BIN FULL SENSOR CAN
RETURN TO ITS NORMAL POSITION.

AIR FILTER
THE ICE MAKER IS EQUIPPED WITH AN AIR FILTER
TO PREVENT DIRT AND DUST ENTERING THE
CONDENSER. IT IS IMPORTANT THAT THE AIR
FILTER IS CLEANED TWICE A MONTH TO ENSURE
EFFICIENT OPERATION OF THE ICE MAKER.
IMPORTANT: FAILURE TO CLEAN THE AIR FILTER
WILL INVALIDATE YOUR WARRANTY AND MAY
CAUSE A COMPONENT FAILURE.
TO CLEAN YOUR AIR FILTER SLIDE THE FILTER OUT
FROM THE FRONT GRILL AND REMOVE ANY DUST
OR DIRT USING A SOFT BRUSH AND A VACUUM
CLEANER. IF THE AIR FILTER IS HEAVILY BLOCKED
WE RECOMMEND USING WATER AND A MILD
DETERGENT TO CLEAN THE FILTER.
IMPORTANT: AIR FILTER MUST BE CLEAN AND
DRY BEFORE REPLACING INTO THE MACHINE.
IMPORTANT: DO NOT OPERATE YOUR ICE MAKER
WITHOUT THE AIR FILTER IN PLACE
PART IV
WARNING
FAILURE TO CLEAN YOUR AIR FILTER COULD
CAUSE COMPONENT FAILURE AND WILL
INVALIDATE YOUR WARRANTY.
CONDENSER CLEANING
A DIRTY OR CLOGGED CONDENSER WILL PREVENT
PROPER AIR FLOW. THIS WILL LEAD TO REDUCED
EFFICIENCY, REDUCED ICE PRODUCTION AND
AN INCREASE IN OPERATING TEMPERATURE
WHICH MAY LEAD TO COMPONENT FAILURE.
WE RECOMMEND THE CONDENSER IS CLEANED
EVERY SIX MONTHS BY A QUALIFIED ENGINEER.
TO CLEAN THE CONDENSER DISCONNECT THE
ICE MAKER FROM THE MAINS ELECTRICITY.
REMOVE THE SCREWS FROM THE BOTTOM
PANEL AND GENTLY REMOVE THE GRILL.
REMOVE DIRT AND DUST FROM THE CONDENSER
FINS WITH A SOFT BRUSH AND VACUUM CLEANER.
REATTACH THE FRONT GRILL AND RECONNECT
POWER TO THE MACHINE.
CL200718UM Rev 1.3 8
WATER DISTRIBUTOR CLEANING
IFYOUR ICE CUBES ARE NOT FORMING CORRECTLY
OR THE OUTPUT OF ICE CUBES DROPS THE WATER
DISTRIBUTOR MAY BE BLOCKED AND REQUIRE
CLEANING.
DISCONNECT THE ICE MAKER FROM THE MAINS
ELECTRICITY.
SLIDE THE AIR FILTER OUT FROM THE SIDE OF THE
FRONT GRILL ASSEMBLY.
LOOSEN THE SCREWS FROM UNDERNEATH THE
FRONT GRILL AND REMOVE THE PANEL.
REMOVE THE LOWER HINGE ASSEMBLY AND
DOOR.
LOOSEN THE SCREWS HOLDING THE TOP COVER
AT THE FRONT AND REAR AND REMOVE THE
PANEL.
TAKE CARE WHEN REMOVING THE TOP COVER
NOT TO DAMAGE THE WIRING FOR THE CONTROL
PANEL.
THE WATER DISTRIBUTOR TUBE WILL BE VISIBLE,
ROTATE THETUBE SOTHAT THE HOLES ARE FACING
UPWARDS. CLEAN OUT THE HOLES WITH A SMALL
BRUSH AND A SOLUTION OF WARM WATER AND
MILD DETERGENT.
AFTER CLEANING RINSE THE TUBE WITH CLEAN
WATER AND RETURN IT TO ITS ORIGINAL POSITION.
REPLACE THE TOP PANEL, HINGE, DOOR, GRILL
PANEL AND AIR FILTER.
PUT THE MACHINE THROUGH A CLEAN CYCLE TO
ENSURE ALL DEBRIS IS FLUSHED THROUGH.
DISCARD ANY ICE MADE FOR THE FIRST 3 HOURS
AFTER CLEANINGTO ENSUREYOU HAVE DISPOSED
OF ANY CONTAMINATED ICE.
WARNING
WATER DISTRIBUTOR CLEANING MUST BE
UNDERTAKEN BY A QUALIFIED ENGINEER.
WARNING
DISCARD ANY ICE MADE FOR THE FIRST 3
HOURS AFTER WATER DISTRIBUTOR CLEANING.
WARNING
ALWAYS WASH YOUR HANDS BEFORE TAKING
ICE FROM THE ICE MAKER

PART IV
WARNING
AFTER LONG TERM STORAGE OR TRANSPORT
YOU NEED TO FOLLOW ALL INSTRUCTIONS IN
PART II OF THIS INSTRUCTION MANUAL WHEN
REINSTALLING THE MACHINE.
CL200718UM Rev 1.3
9
PREPARING YOUR ICE MAKER FOR LONG TERM
STORAGE OR MOVING
IF THE ICE MAKER NEEDS TO BE STORED FOR A
LONG PERIOD OF TIME OR IT NEEDS TO BE MOVED
TO A NEW LOCATION THE WATER SYSTEM WILL
NEED TO BE FULLY DRAINED.
PUT THE ICE MAKER INTO STANDBY MODE
AND DISCONNECT THE UNIT FROM THE MAINS
ELECTRICITY.
TURN OFF THE MAINS WATER SUPPLY AND
DISCONNECT THE WATER INLET HOSE.
REMOVE ALL REMAINING ICE FROM THE STORAGE
BIN.
DISCONNECT THE SILICON HOSE FROM THE
WATER RESERVOIR TO TOTALLY DRAIN THE
WATER SYSTEM. WHEN ALL WATER IS DRAINED
RECONNECT THE HOSE TO THE WATER TANK.
CLEAN THE INSIDE OF THE ICEMAKER AND
THOROUGHLY DRY THE INSIDE WITH PAPER
TOWELS.
FOR TRANSPORTING TO A NEW LOCATION
TAPE THE DOOR SHUT WITH A LOW TACK TAPE
(MASKING TAPE).
FOR LONG TERM STORAGE LEAVE THE DOOR OPEN
AT LEAST 50MM TO ALLOW FOR AIR FLOW INTO
THE ICE MAKER. THIS WILL PREVENT MOLD AND
MILDEW FORMING.
ICE PRODUCTION SYSTEM
MINERALS AND LIME SCALE THAT ARE PRESENT IN
THE WATER ARE REMOVED DURING THE FREEZING
CYCLE AND WILL BUILD UP IN ICE PRODUCTION
SYSTEM. CLEANING THE SYSTEM REGULARLY WILL
HELP TO REMOVE THE LIME SCALE BUILD UP. WE
RECOMMEND CLEANING THE ICE PRODUCTION
SYSTEM EVERY SIX MONTHS WITH A CITRIC ACID
SOLUTION.
WARNING
DE-SCALING MUST BE CARRIED OUT BY A
QUALIFIED ENGINEER.
WARNING
WE RECOMMEND FITTING AN IN LINE WATER
FILTER TO REDUCE LIME SCALE BUILD UP AND
IMPROVE THE QUALITY AND TASTE THE ICE
WARNING
LIME SCALE BUILD UP WILL REDUCE THE
EFFICIENCY OF THE ICE MAKER AND COULD
LEAD TO COMPONENT FAILURE WHICH WOULD
NOT BE COVERED UNDER WARRANTY
WARNING
CONDENSER CLEANING MUST BE CARRIED
OUT BY A QUALIFIED ENGINEER
WARNING
FAILURE TO CLEAN YOUR CONDENSER COULD
CAUSE COMPONENT FAILURE AND WILL
INVALIDATE YOUR WARRANTY.

SYMPTOM POSSIBLE CAUSE SUGGESTED SOLUTION
ICE PRODUCTION DOES NOT START
ICE MAKER NOT CONNECTED
TO MAINS ELECTRICITY
CORRECTLY
• CHECK POWER IS ON AT THE SOCKET
• CHECK CABLE IS CORRECTLY PLUGGED IN
• CHECK FOR DAMAGE ON POWER CABLE, USE A QUALIFIED ENGINEER TO
REPLACE IF NECESSARY
MACHINE IS IN STANDBY • PRESS POWER ON/OFF BUTTON, DISPLAY SHOULD READ 00
FUSE BLOWN OR CIRCUIT
BREAKER TRIPPED
• CHECK FUSE IN MAIN 13AMP PLUG
• CHECK FUSE OR CIRCUIT BREAKER AT MAIN DISTRIBUTION BOARD
AMBIENT TEMPERATURE TOO
HIGH • WAIT UNTIL AMBIENT TEMPERATURE DROPS BELOW 32°C
WATER SUPPLY OFF OR WATER
PRESSURE TOO LOW
• CHECK THE WATER SUPPLY TO THE ICE MAKER IS TURNED ON
• CHECK THE WATER PRESSURE IS BETWEEN 1.4 AND 5.5 BAR - INCREASE
WATER PRESSURE IF NECESSARY
FLOAT VALVE NOT OPERATING • CLEAN FLOAT OR REPLACE IF NECESSARY
LOOSE CONNECTION OR
FAULTY CONTROL BOARD • CHECK FOR LOOSE CONNECTION, REPLACE IF NECESSARY
COMPRESSOR IS RUNNING BUT ICE IS NOT
BEING PRODUCED
REFRIGERANT LEAK • CHECK FOR REFRIGERANT LEAK AND REPAIR, RECHARGE SYSTEM AS PER
THE DATA PLATE
HOT GAS BYPASS VALVE HAS
FAILED OPEN • CHECK AND REPLACE HOT GAS BYPASS VALVE
BLOCKAGE IN SYSTEM • CLEAR BLOCKAGE, REPLACE FILTER DRIER AND RECHARGE SYSTEM AS PER
THE DATA PLATE
COMPRESSOR WIRING LOOSE
OR DEFECTIVE • CHECK FOR LOOSE CONNECTION, REPLACE IF NECESSARY
LOOSE CONNECTION OR
FAULTY CONTROL BOARD • CHECK FOR LOOSE CONNECTION, REPLACE IF NECESSARY
NO WATER IN ICE PRODUCTION SYSTEM
WATER PUMP FAULTY • CHECK FOR LOOSE CONNECTION, REPLACE IF NECESSARY
FLOAT VALVE NOT OPERATING • CLEAN FLOAT OR REPLACE IF NECESSARY
WATER PRESSURE TOO LOW OR
WATER LEAK
• CHECK THE WATER SUPPLY TO THE ICE MAKER
• CHECK THE WATER PRESSURE IS BETWEEN 1.4 AND 5.5 BAR - INCREASE
WATER PRESSURE IF NECESSARY
ICE PRODUCTION SYSTEM
BLOCKED WITH LIME-SCALE • DE-SCALE AND CLEAN SYSTEM THOROUGHLY
LOOSE CONNECTION OR
FAULTY CONTROL BOARD • CHECK FOR LOOSE CONNECTION, REPLACE IF NECESSARY
ICE PRODUCTION SLOW
CONDENSER OR AIR FILTER
DIRTY • CLEAN AIR FILTER AND CONDENSER AS NECESSARY
INADEQUATE AIR FLOW
AROUND ICE MAKER • CHECK FOR ADEQUATE AIR FLOW ON ALL SIDES OF ICE MAKER
CONDENSER FAN NOT
WORKING • CHECK FOR LOOSE CONNECTION, REPLACE IF NECESSARY
HIGH AMBIENT TEMPERATURE • WAIT UNTIL AMBIENT TEMPERATURE DROPS BELOW 32°C
ICE PRODUCTION SYSTEM
BLOCKED WITH LIME-SCALE • DE-SCALE AND CLEAN SYSTEM THOROUGHLY
ICE NOT RELEASING FROM THE
EVAPORATOR, ICE DOES NOT FALL INTO
STORAGE BIN
MACHINE NOT LEVEL • CHECK MACHINE IS PERFECTLY LEVEL
LOW AMBIENT TEMPERATURE • WAIT UNTIL AMBIENT TEMPERATURE INCREASES ABOVE 10°C
HOT GAS BYPASS VALVE HAS
FAILED CLOSED • CHECK AND REPLACE HOT GAS BYPASS VALVE
EVAPORATOR SENSOR FAULTY • CHECK AND REPLACE AS NECESSARY
LOOSE CONNECTION OR
FAULTY CONTROL BOARD • CHECK FOR LOOSE CONNECTION, REPLACE IF NECESSARY
ICE PRODUCTION DOES NOT STOP WHEN
BIN IS FULL
BIN FULL SENSOR NOT
WORKING • CHECK FOR LOOSE CONNECTION, REPLACE IF NECESSARY
LOOSE CONNECTION OR
FAULTY CONTROL BOARD • CHECK FOR LOOSE CONNECTION, REPLACE IF NECESSARY
BIN FULL SENSOR HAS LIME-
SCALE BUILD UP • FULLY DE-SCALE ICE PRODUCTION SYSTEM
CLOUDY OR BADLY FORMED ICE CUBE
WATER DISTRIBUTOR DIRTY OR
HAS LIME-SCALE BUILD UP • FULLY DE-SCALE AND CLEAN ICE PRODUCTION SYSTEM
POOR INCOMING WATER
QUALITY • CHANGE WATER SUPPLY OR FIT AN IN-LINE WATER FILTER
PART V
TROUBLESHOOTING
CL200718UM Rev 1.3 10

CL200718UM Rev 1.3
11
Please make note of your equipment details for future reference
Model Number
Serial Number
Date of purchase
Date of installation
Supplied by
Phone Number
ICE PRODUCTION 22KG PER 24 HOURS
ICE STORAGE 7KG STORAGE BIN
VOLTAGE 230V/50HZ
RATED POWER 155W
CLIMATE CLASS SN,N,ST
REFRIGERANT R290
REFRIGERANT CHARGE 55G
UNIT DIMENSIONS 380 X 470 X 600 (W,D,H MM)
AMBIENT OPERATING AIR TEMPERATURE 10°C - 32°C
WATER SUPPLY TEMPERATURE 7°C - 32°C
WATER SUPPLY PRESSURE 1.4 - 5.5BAR
SPECIFICATION

CL200718UM Rev 1.3
Project Distribution Ltd
Unit 1 Sun Street
Stoke on Trent
United Kingdom
ST1 4JW
Tel: [phone]
www.project-distribution.co.uk
[email protected]