Progrill CS157 User manual

formerly DOUGHPRO. New Name. Same Quality. Superior Service.
proluxe.com
Operations Manual
Model: CS157
15”x 7” Clamshell Grill

Operation Instructions
Please read carefully before attempting to use this appliance.
Step 1. Carefully unpack and clean grill plates with mild soap then sponge clean
with cold water.
Step. 2. Place in location where it will be used allowing for clearances per the
dimensions indicated.
WARNING! Allow 2” minimum clearance between adjacent equipment and/or
wall areas.
Do not touch hot surfaces.
Step 3. Plug into proper 3 prong wall outlet. If other appliances are connected
to the same circuit make sure the total load does not exceed maximum
ampacity of the circuit. Electrical information is as follows:
120V/60Hz/1 phase/1150W/9.6 Amps
208V/60Hz/1 phase/2800W/13.5 Amps
Step 4: Warm-up
Energize by turning on the power switch which will illuminate when turned
on. The display flashes and shows left preset timer during warm-up. Pre-
heat temperature time will be 40-50 minutes. When the set point is
reached, the display stops flashing and beeps 3 times.
Step 4: Operation
Simply place product on grill, close lid and press the
desired pre-set time cycle (ex: 10 seconds). After the time cycle is
finished press it again to reset the time cycle.
Cleaning Instructions
NOTE! Always turn off power and allow to cool down before attempting to clean.
Never submerge grill in water or other liquid nor use mineral spirits
or other flammable material to clean this appliance.
!Never use ice to cool down grill, warranty will be void!
Clean stainless steel and griddle surfaces with soap and water using a
soft, clean cloth periodically as required, but at least once daily. Never
use harsh abrasives. Use only non-abrasive scouring pads when required.

Clean Cycle
275°F is the factory default temp for the CLEAN cycle. To change the CLEAN cycle temp, simultaneously
hold down the TEMP and CLEAN buttons for 15 seconds.
Using the up or down arrows to adjust to the desired temp.
To start a clean cycle, push CLEAN button once so the CLEAN LED light is turned on. All preset LED’s are
turned off, and the temperature set point is changed to the clean set point of 275°F. This also initiates
the cool down to clean set point condition as well the display starts flashing until the clean set point is
reached.
To stop the clean cycle, simply press the CLEAN button once to deactivate the clean cycle. The CLEAN
LED is turned off, the preset LED’s are restored, the temperature set point is changed to the main set
point. Again, the warm-up condition is initiated and the display flashes until the cook set point is
reached.

CS157 Operating Instructions:
1. Press desired time to start the time cycle. After the cycle is finished, press it again to
reset the time cycle
2. If for any reason the timer has to be reset in the middle of a cycle, you must press and hold
the corresponding timer button for 3 seconds.

Instruction’s for Adjusting the Temperature
PRESS and hold the TEMP and
ARROW up
buttons simultaneously for 15
seconds.
Using the ARROW buttons, you
may now adjust the temperature
to your desired setting.
Once you have set your desired
temperature simply push
the TEMP button. The digital
displays will now read the
preset times.
Instruction’s for Adjusting the Set-Time
PRESS the desired button you
wish to program.
Now press BOTH button and
TEMP buttons simultaneously
for 5 seconds.
The digital displays will now read their preset
time. The unit is capable of having
up to 4 different settings.
Now using the ARROW buttons you
can set your desired time.
Once you have set the desired time simply press the
TEMP button, the unit will display the new set-time.

55
14
56
57
76
52
54
51
68 18
23
36
12
11
88
14
24
14
44
53
45
71
1
MODEL CS157
A2P
SHEET 1 OF 3
EXPCS157 R4 1012 102113
A2
71A
A1P
79
A1

69
51
A4
52
54
A4P
78A
SHEET 2 OF 3
MODEL CS157
13
19
72
17
37
73
37
17
41
42
50
36
37
66
20 63
64
20
21
51
75
3
10
60
54
78
69
51
A7
52
EXPCS157 R4 1012 102113
CS157P

89
77 27 38 58
43 46
47
34
9
46
43
48 4
30
5
646 43
33
7
8
62 84 83 61
84 82 15
48
84
32
28
29
32
29
70
37 42 16
65
47
17
17
22
67
49
40
84
28
46
SHEET 3 OF 3
A6P
MODEL CS157
EXPCS157 R4 1012 102113
CS157P
29
43
A6
90

MODEL CS157 PARTS LIST
MODEL
CS157A
MODEL
CS157PA
QTY.
ITEM # DESCRIPTION 120V 120V
1 LOWER WRAP AROUND SHROUD ASSY 110103901 110103901 1
3 SPRING, DETENT 1/2 LONG 110115555 110115555 1
4 FUSE HOLDER MPPF708 MPPF708 1
5 FUSE BUSS 1 AMP MPPF701R MPPF701R 1
6 TRANSFORMER 11096975 11096975 1
7 TERMINAL BLOCK #6 6016 6016 1
8 STRAIN FELIEF 11016546468 11016546468 1
9 CORD, POWER 120V 110969174 110969174 1
10 TUBBING-PAD 110115531 110115531 1
11 COVER, LOWER PLATTEN ASSY 110103909 110103909 1
12 LOWER PLATEN INSULATION 110103910 110103910 1
13 GREASE TRAY 110103903 110103903 1
14 GREEN INSULATION WASHER C4401 C4401 9
15 TOP LINK 110115508 110115508 1
16 BOLT, HEX 5/16-18 X1 1/2 SST BH516181S BH516181S 2
17 E-CLIP, RETAINING RING LCC3478 LCC3478 2
18 PIN, BACK STOP 110115543 110115543 1
19 HANDLE GRIP 110901168 110901168 1
20 SST SET SCREW KNURLED CUP POINT 5/16-18 x 3/8 SST5161838KN SST5161838KN 6
21 RUBBER GROMET, 5/16 X 1/2 110115554 110115554 1
22 INSULATION, UPPER PLATEN RIGHT HAND 110888251R 110888251R 1
23 BUSHING, TEFLON , 3/4" LONG 110113441 110113441 1
24 GROMET, RUBBER 3/4 X 1 3/8 110103919 110103919 1
27 SPACER, NYLON 1/4X.141 X 9/32 11090109 11090109 4
28 WASHER, SAE #8 WSAE8 WSAE8 4
29 NUT, HEX 8-32 NH832 NH832 3
30 SCREW, PAN HEAD PHILLIPS 2-56 X1/4 SP25614 SP25614 1
31 WASHER #5/16 INTERNAL TOOTH LOCK WLIT516 WLIT516 2
32 WASHER #8 INTERNAL TOOTH LOCK WLIT8 WLIT8 2
33 RELAY 110942520 110942520 2
34 BOTTOM COVER 110103917 110103917 1
36 FLANGE TEFLON BUSHING 110115563 110115563 1
37 BUSHING TEFLON 1” LONG 110115541 110115541 3
38 WASHER, STEEL 311150019 311150019 4
40 MARKER STRIP #6 DOUBLE MS6016 MS6016 1
41 WASHER, CUT 5/16-18 WC516 WC516 3
42 WASHER, 5/16 SPLIT LOCK WL516 WL516 5
43 WASHER, #6 INTERNAL TOOTH LOCK WLIT6 WLIT6 12
44 WASHER, SAE 3/8 WSAE38 WSAE38 4
45 NUT, HEX 3/8-16 NH3816 NH3816 4
46 NUT, HEX 6-32 NH632 NH632 12
47 SCREW, PHILLIPS 8-32X3/8 SST SP83238S SP83238S 13
48 SCREW, PHILLIPS 6-32X3/8 SP63238 SP63238 6
49 SCREW, PAN HEAD SLOTED 10-32 X 3/8 SST SPS103238S SPS103238S 6
50 SCREW, SOCKED HEAD 5/16-18 X 3/4 SSH5161834 SSH5161834 3
51 SCREW, SET 3/8-16 X 1/2 SST381612 SST381612 3
52 SCREW, PAN HEAD PHILLIPS 6-32 X1/4 SP63214 SP63214 2
53 WASHER 3/8 SPLIT LOCK WL38 WL38 4
54 WASHER, SAE #6 WSAE6 WSAE6 2
55 BOLT, HEX 1/4-20 x 1.00 SST BH14201S BH14201S 1
56 WASHER, SAE 1/4" WSAE14 WSAE14 1
57 WASHER, SPLIT LOCK , 1/4" WL14 WL14 1
58 DIGITAL CONTROL 110171433052 110171433052 1
60 PLUNGER ASSY 110115544 110115544 1
61 UPPER LEVELING BRACKET 110115510 110115510 1
62 UPPER LEVELING SHIM 110115557 110115557 1
63 HANDLE, SPRING ADJUSTING COLLAR 110115528 110115528 1
64 COLLAR, HOLDER 110115530 110115530 1
65 BACK COVER 110103907 110103907 1
66 COUNTER BALANCE SPRING 1101039154 1101039154 1
67 RIGHT SHROUD ASSY 11016546455 11016546455 1
68 RTD SENSOR (LOWER) 1108881102 1108881102 1
PLCS157 R4 1012 102113.DOC

MODEL CS157 PARTS LIST
MODEL
CS157A
MODEL
CS157PA
QTY.
ITEM # DESCRIPTION 120V 120V
69 RTD SENSOR (TOP) 1108881101 1108881101 1
70 SCREW, PAN HEAD PHILLIPS 8-32 X1 SP8321 SP8321 1
72 HANDLE RIGHT ASSY 110103916 110103916 1
73 CLEVIS ASSY, RIGHT HAND 110115504 110115504 1
75 SST SET SCREW 3-8-16 X 1.00 SST38161 SST38161 1
76 NUT, SERRATED FLANGED HEX 1/4-20 NHSF1420 NHSF1420 1
77 OVERLAY OCS157 OCS157 1
78 UPPER PLATEN, RIGHT 110115540R120 11011557R120 1
79 WIRE HARNESS 110103950 110103950 1
82 PIN, PIVOT BACK 110115566 110115566 1
83 PIN, PIVOT FRONT 110115565 110115565 1
84 RETAINING RING 110115567 110115567 4
87 MANUAL CS157 MSCS157 MSCS157 1
88 SST SET SCREW 3-8-16 X 1 1/2 SST3816112 SST3816112 4
89 TRANSFORMER INSULATION 1101159180 1101159180 1
90 SCREW, PHILLIPS 6-32X5/8 SP63258 SP63258 2
A1P LOWER PLATEN PANINI WITH WIRING N/A 110103932307 1
A1 LOWER PLATEN WITH WIRING 110103932207 N/A 1
A2P LOWER PLATEN PANINI ASSEMBLY N/A 110103932PK 1
A2 LOWER PLATEN ASSEMBLY 110103932K N/A 1
A4P UPPER PLATEN PANINI RIGHT HAND WITH WIRING N/A 1101155304 1
A4 UPPER PLATEN RIGHT HAND WITH WIRING 1101155204 N/A 1
A6P UPPER PLATEN PANINI RIGHT HAND ASSEMBLY N/A 1101155313 1
A6 UPPER PLATEN RIGHT HAND ASSEMBLY 1101155113 N/A 1
A7 SCRAPER, PANINI 110115580 110115580 1
PLCS157 R4 1012 102113.DOC

PLEASE READ CAREFULLY BEFORE ATTEMPTING TO USE THIS APPLIANCE.
LIMITED MACHINE WARRANTY
Doughpro warrants the CS157, from manufacturing defects in workmanship and material sold within
the domestic United States.
WHAT IS COVERED
One year warranty for parts and labor. The heating elements on the upper and lower platens have
a limited lifetime warranty on the elements.
HOW LONG DOES THE COVERAGE LAST
We will repair or replace the defective CS157 on normal warranty one year parts and labor. The
heating elements on the upper and lower platen only; will be replaced by next day air service;
under the normal one year warranty. Such repair or replacement will be at the expense of
Doughpro on under the normal one year warranty.
WHAT WE WILL DO
Contact our Factory to obtain warranty service. Doughpro must issue a return authorization
number, and call tag, or find the name and location of a Factory Authorized Service Center
nearest you. When calling for service, please furnish the model number, serial number, and a
description of the problem.
HOW TO GET SERVICE
THE WARRANTIES PROVIDED BY DOUGHPRO DO NOT APPLY IN THE FOLLOWING
INSTANCES:
WHAT THIS WARRANTY DOES NOT COVER
*Do not * Do not apply ice to grill surface as this will cause it to warp and void the warranty. Do
not use abrasive cleaners not specified by Doughpro .Do not use abrasive material such as grill
blocks or metallic scrubbers to clean the grill surface. Do not place unit in sink to wash down or
apply water to the unit
• Damage due to misuse, abuse, alteration, or accident.
• Improper or unauthorized repairs.
• Submerged in water.
• Dropped.
• Damage in shipment.
• Equipment exported to foreign countries.

Warranty & Return Policy
Proluxe warrants all products manufactured by it against defects in workmanship or materials from the date of purchase for a period of
(1) year on parts and labor. This warranty applies to only equipment purchased and used in the United States. Warranty period
shall begin when equipment ships and will not exceed 90 days past the original shipment date. Warranty travel shall only
be covered for 60 miles.
ALL WARRANTY SERVICE CALLS MUST BE APPROVED BY PROLUXE. IF THIS PROCEDURE IS NOT FOLLOWED,
WARRANTY SERVICE WILL NOT BE COVERED. WARRANTY SERVICE WILL BE PAID ON STRAIGHT TIME, OVERTIME WILL
NOT BE COVERED.
Exclusions:
1. WOOD / GAS FIRED OVENS: PROLUXE warranty applies to the main body of the oven being steel / refractory and insulation shall
be free from defects in materials and workmanship for a period of four years from the date of purchase. The gas equipment shall be
free from defects in materials and workmanship for a period of one (1) year
from the date of purchase. This warranty excludes the tandoori and home oven. Lifetime warranty against cracks on oven floor.
2. TANDOORI & HOME OVENS: PROLUXE warrants the Tandoori & Home Oven including gas equipment shall be free from defects
in materials and workmanship for a period of one (1) year from the date of purchase.
3. Air compressors are excluded from this warranty, but PROLUXE may act as a warranty expeditor in certain instances regarding
these compressors. The air compressor manufacturer provides a limited warranty
and a copy of this warranty is furnished with all compressors sold by PROLUXE. For prompt handling of compressor warranty claims
the instructions of the compressor manufacturer must be adhered to.
4. Equipment built to special order as well as accessories are not returnable unless defective within the terms of this warranty.
5. In no event shall PROLUXE be liable for consequential damages arising out of the failure of any of its products if operated
improperly or caused by normal wear or damage by operator abuse.
6. BC2325 pedestal warranty disclaimer: Pedestals shall only be covered under warranty if they have been cleaned using the factory
approved cleaning method. cracked or damaged pedestals must be inspected by the factory before warranty is authorized.
Returned Merchandise Policy:
Should it become necessary to return any of the company’s products, the following instructions must be adhered to: First,
contact our customer service department for approval and a return authorization number. Please have the serial number
of your item available at that time. All merchandise must be shipped freight prepaid by customer or service agency.
Subject to the inspection of the product by the company, a restocking charge of 20% of the Net purchased price paid to
PROLUXE will be assessed. Merchandise may not be returned for credit without prior written approval of PROLUXE. Collect shipments
will not be accepted. No returns after 60 days of original shipment date on machines. Purchased parts may not be returned after 30
days.
If upon inspection by PROLUXE or its authorized agent it is determined the equipment has not been used in an appropriate manner,
has been modified, or has not been properly maintained, or has been subject to misuse,
misapplication, neglect, abuse, accident, unauthorized modification, damage during transit, delivery, fire, flood, act or war,
riot or act of God, then this warranty shall be deemed null and void.
Terms & Conditions:
1. Prices indicated in the PRICE LIST are suggested retail prices and are shown in U.S. DOLLARS.
2. Terms of Payment: 1% 10 days, NET 30 days.
3. NEW ACCOUNTS: Satisfactory credit information must be provided before open account status can be extended.
Unless agreed otherwise, all shipments will be made C.O.D., CASH IN ADVANCE.
4. PRICING: Prices, specifications, model numbers, capacities and accessories are subject to change without notice.
5. FREIGHT / ROUTING: Method of shipment will be determined by PROLUXE unless otherwise
advised by PURCHASER.
6. DAMAGED CLAIMS: All merchandise shipped at purchaser’s risk. Inspection must be made by purchaser at time
goods are received. If goods are damaged, the PURCHASER shall request that the agent of the transportation
company make a written notation on the proper shipping documents immediately and then file a claim for damage.
GOODS DAMAGED IN SHIPMENT ARE NOT RETURNABLE.
7. RETURNS: Machines may not be returned after 60 days. Purchased parts may not be returned after 30 days. A
restocking fee of 20% will be assessed on non-warranty returns.
8. TAXES: Prices indicated herein DO NOT include State, Federal, Local or foreign taxes or duties, nor do they include
fees, permits, insurance or other levies, all of which are the responsibility of the purchaser.
9. All orders are subject to acceptance by PROLUXE.
10. Possession of this price list shall not be considered an offer to sell.