PROKORD DUSBKF1-84 User manual

User Manual
DUSBKF1-84

Installation Instructions for Mobile Brackets
Number Describe Quantity Position
Mobile Stent
1
2
3
4
5
6
7
8
9
11
12
13
15
10
14
Base
2.5 inch universal caster belt brakes
2.5 inch universal casters without brakes
Moving bracket column left
Moving bracket column right
Laminate
Cross hexagon head composite belt
M6*16
M14 cushion (spring washer GB859),
M14 flat cushion (small gasket-A grad
GB848), M14 nut (type 1 hexagon nut
GB6170)
Cross head combination screw M6*16
Wall hanging beam
Wall hanging vertical beam
M5*100 crosshead screw
M8*70 cross hexagon bolt
M8 cushion (spring washer GB859), M8
flat cushion (gasket-A grade GB848),
M8 nut (type 1 hexagon nut GB6170)
Hexagon wrench
1 PCS
2 PCS
2 PCS
1 PCS
1 PCS
1 PCS
16 PCS
Each 4 PCS
4 PCS
1 PCS
2 PCS
2 PCS
4 PCS
Each 4 PCS
1 PCS
Assembly with base
Assembly with base
Assembly with base
Assembly with base
Assembly with left
and right columns
Caster and base
assembly
Pillar and base
assembly
Laminate and column
assembly
Assembly with pillars
Assembly with whole
machine and crossbeam
Assembly with wall-
mounted vertical beam
Assembly of wall-
mounted crossbeams
and columns
Assembly of wall-
mounted crossbeams
and columns
Assembly of hexagonal
bolts
1

Mobile bracket assembly and installation steps:
2. Remove the left and right column of the movable support in turn from the packing box,
insert the welded M14*70 bolt on the column into the corresponding assembly hole of the
base in the direction (pay attention to the M6 thread on the side of the column in the inner
side). Put M14 cushion and M14 cushion on the welded M14*70 bolt on the column in turn,
and then fasten it with M14 hexagonal nut, as show in Figure B. Remove the layer board
from the packing box and use M6*1610. The laminate is assembled between the left and
right columns by the combination screw of the head of the word plate. The operation
schematic is show in Figure C. Attention direction.
1. Remove the base from the packing box. Firstly, assemble the casters to the corresponding
position of the base with M6*16 bolts combined with cross screwdriver and cross hexagonal
head. The operation schematic diagram is shown in Figure A.
2
Cross hexagonal head corbination 16 bolt
(Quantity: 16PCS)
2.5 inch univorsal caster belt brake
(Quntity: 2PS)
Figure A
Figure B

3
3.Remove the standard wall-mounted cross beam from the packing box, assemble
the M8*70 hexagonal bolt and M8 nut with hexagonal wrench and cushion pad in
turn on the left and right columns of the mobile support (upper and lower
positions should be adjusted according to personal needs), and the operation
schematic diagram is as shown in Figure D, rotate the M5*100 screw on the wall-
mounted vertical beam to the position show in the local graph a, and then
assemble the wall-mounted vertical beam and the machine with a screwdriver.
Draw a schematic diagram as shown in Figure E. Finally, hang the machine with
the vertical beam on the wall-mounted cross beam (refer to the assembly drawing
of the wall-mounted bracket), then lock the M5*100 screw to the top of the wall-
mounted cross beam with a long screwdriver. The operation schematic diagram is
as follows: the assembly drawing of the wall-mounted bracket and the local graph
B.
Figure C
Figure D

4
Front of wall mounting bracket asseably drawing
Figure E

5
Too parameters
Long screwdriver, hexagonal wrench.
Be careful:
1. In order to guide the installation of the
conference mobile bracket correctly,
please read the instructions carefully
when installing the bracket.
2. Please commission a professional
installation company to install the
conference mobile bracket.
3. When reading or using this manual, if
you do not understand it, please contact
our company.
4. The illustrations in this manual are for
reference only. In practice, please refer to
the physical objects.