PROLiNK PRT7007L User manual

Quick Installation Guide
Portable 4G LTE WiFi Hotspot
MODEL NO:
PRT7007L
Version 1.00
(English / Indonesian)
BEFORE GETTING STARTED
This document is designed to aid you to get started with the device. If you experience problems following
these guides or need further information pertaining to the device, please visit our website at
www.prolink2u.com. All specifications are subject to the manufacturer’s configuration at the time of
shipping and may change without prior notice, written or otherwise.

1. Package Contents
Items:
One (1) PROLiNK®PRT7007L with built-in 2300mAh
Lithium (Li-ion) Battery
One (1) unit of USB Cable
One (1) piece of Quick Installation Guide (QIG)
1
2
3
Note:
1. The illustrations in this document may appear different from your model.
2. If any of above item is not packed in your package when open, please consult
your reseller immediately.
EN 1
12
3
Quick Installation Guide
Portable 4G LTE WiFi Hotspot
MODEL NO:
PRT7007L
Version 1.00
(English / Indonesian)
BEFORE GETTING STARTED
This document is designed to aid you to get started with the device. If you experience problems following
these guides or need further information pertaining to the device, please visit our website at
www.prolink2u.com. All specifications are subject to the manufacturer’s configuration at the time of
shipping and may change without prior notice, written or otherwise.

2. Overview
4
1
Interface and Buttons
1. SIM/USIM Card Slot /
Reset Button
2. WPS Button
3. Power Button
EN 2
2
3
4
5
6
7
4. LCD Screen
6. Charger/USB port
7. AUX Antenna Connector
8. Main Antenna Connector
Indicators
When the device is powered on, the following icons may be displayed
on the LCD screen. For a description of the icons, refer to the
following table.
Network signal strength.
Network type. The 4G or 3G icon is displayed on the LCD
screen depending on the connected network.
3G, 4G
The user is in roaming status.

2. Overview
3. Hardware Installation
EN 3
12 3
Network in use.
One or more new messages are received.
Wi-Fi status and the number of connected users.
Battery power.
Inserting SIM Card
1. Open the SIM (or USIM) card cover.
2. Insert a SIM (or USIM) card to the card slot, you will hear a click
sound when the SIM (or USIM) card is locked in place.
3. Close the SIM (or USIM) card cover.
Note:
1. Open the card slot cover gently.
2. PRT7007L does not support the Micro/Nano SIM card. To avoid damaging the
device, do not use Micro/Nano SIM cards or with any card holders.

EN 4
3. Hardware Installation
Note:
1. If the system does not launch installation automatically, you can run the
installation program in the path of My Computer > PROLiNK 4G.
2. The driver of your device will be installed at the same time.
PRT7007L supports three working modes.
i. USB Mode – Connection via the USB cable.
• Connect your device to the client with the USB cable.
• Power on your device.
• Follow the system prompts to complete the software
installation.
• After the installation, the system will create a shortcut icon on
your desktop. Double click on the shortcut and it will lead you
to the web configuration page of PRT7007L.
Unless you need to change your 3G/4G settings or access the
advanced settings of the device, you can access the Internet without
the need to configure the device.
The WAN connection mode is “Automatic” by default.

EN 5
ii. Wi-Fi mode - Connection via Wi-Fi
Power on your device directly.
It will take 1~2 minutes to initialize.
Use your normal Wi-Fi application on the client to search for the
available wireless network.
Select the SSID of your device (default SSID is
PROLiNK_PRT7007L_xxxxx), and then click Connect. The password is
set as prolink12345 by default.
The WAN connection mode is “Automatic” by default. You can access
the Internet without the need to configure the device.
If you need to change your 3G/4G settings or access the advanced
settings of the device, refer to “Accessing the WebGUI configuration
page”
3. Hardware Installation

EN 6
3. Hardware Installation
4. Web-based Conguration
iii. Mixed Mode – Connection via both USB and Wi-Fi
This is a combination of using the USB cable and Wi-Fi connection.
Input the case-sensitive default password “password”, and then click
Login to access the WebGUI configuration page.
Accessing the WebGUI Configuration Page
Make sure the connection between your device and the client is
active. Launch the Internet browser and enter http://192.168.123.1 or
http://p.home
The login page will appear as follow.

EN 7
Select Settings > Network Settings Change Connection Mode,
Network Selection or APN
Setting.
Select Settings > Wi-Fi Settings Change the basic wireless
network settings, choose
security mode and WPA
type, and perform the WPS
configuration.
Select Settings > Device Settings Change the Administrator
settings, restore factory
default, manage PIN or set the
LAN interface configuration.
Setting
After logging in, you can also select Settings, and do the following
operations.
Quick Setup
After logging in, select Settings > Quick Settings, and then the Quick
Setup wizard will appear.
The Quick Setup wizard will guide you on setting up the basic
parameters for your device in the safest way. After this procedure,
you can use your Internet service.
4. Web-based Conguration
Note:
If you select Manual APN, please consult your ISP on the APN name to be entered.

EN 8
Enabling 2.4GHz / 5GHz Dual Band
i. Under Settings > Wi-Fi Settings > Basic Settings, select Enable for
Multi SSID Switch and click Apply
4. Web-based Conguration
Select Settings > Firewall Set the Mac/IP/Port Filtering,
Port Forwarding or the System
Security configuration.
Select Settings > Router Settings Change Router LAN IP and
DHCP settings.
Select Settings > Internet Wi-Fi Connect to Hotspot as Wi-Fi
repeater.

ii. Under Settings > Wi-Fi Settings > Advanced Settings, select
Enable for Multi Band Switch and click Apply
4. Web-based Conguration
EN 9

4. Web-based Conguration
iii. Under Settings > Wi-Fi Settings > Basic / Advanced Settings, the
Guest SSID / Guest SSID setting will appear. Users can view or edit
5GHz SSID and Password.
EN 10

Disconnect from the Internet
1. Log in the WebGUI Configuration page, and go to Home.
2. Click Connect / Disconnect to connect or to terminate the Internet
connection.
Sleep Mode
The device will enter into Sleep Mode when no users are connected
to the device in 10 minutes. Press Power or WPS button to wake up
the device.
Note:
With USB connection and no Wi-Fi user connected to the device within 10 minutes,
only the Wi-Fi function will be disabled. Hold the WPS button for about 3 seconds
to enable this function.
Note:
Turning off the device can also terminate the Internet connection.
4. Web-based Conguration
EN 11

Items:
Satu (1) PROLiNK®PRT7007L with built-in 2300mAh
Lithium (Li-ion) Battery
Satu (1) unit of Kabel USB
Satu (1) buah Lembar Panduan Instalasi
1
2
3
Catatan:
1. Ilustrasi dalam dokumen ini mungkin tampak berbeda dari model anda.
2. Jika salah satu item di atas tidak dikemas dalam paket anda ketika terbuka,
silakan berkonsultasi dengan reseller anda segera.
12
3
1. Isi Kemasan
ID 1
Quick Installation Guide
Portable 4G LTE WiFi Hotspot
MODEL NO:
PRT7007L
Version 1.00
(English / Indonesian)
BEFORE GETTING STARTED
This document is designed to aid you to get started with the device. If you experience problems following
these guides or need further information pertaining to the device, please visit our website at
www.prolink2u.com. All specifications are subject to the manufacturer’s configuration at the time of
shipping and may change without prior notice, written or otherwise.

ID 2
2. Penjelasan
4
1
Tombol dan Antarmuka
1. Slot Kartu SIM/USIM /
Tombol Reset
2. Tombol WPS
3. Tombol Power
2
3
4
5
6
7
4. LCD Screen
6. Charger/USB port
7. AUX Antenna Connector
8. Main Antenna Connector
Indikator
Bila perangkat diaktifkan, ikon berikut akan ditampilkan pada layar
LCD. Untuk penjelasan dari ikon, lihat tabel berikut.
Menunjukkan kekuatan signal.
jaringan signal meter. Signal yang di tunjukkan pada layar
tergantung signal yang didapat dari provider.
3G, 4G
Menunnjukkan status roaming.

3. Instalasi Perangkat
12 3
Jaringan sedang digunakan.
Pesan SMS diterima.
Satus WIFI dan jumlah pengguna yang terkoneksi pada
PRT7007L.
Battery.
Memasukkan Kartu SIM
1. Buka penutup SIM (atau USIM).
2. Masukkan SIM (atau USIM) ke dalam slot SIM, akan terdengar
bunyi klik jika SIM (atau USIM) sudah benar-benar terpasang.
3. Tutup penutup SIM (or USIM).
Catatan:
1. Buka penutup SIM secara perlahan.
2. PRT7007L tidak dapat mendukung Micro/Nano SIM, maka akan terjadi
kerusakan, Jangan menggunakan Micro/Nano SIM.
ID 3
2. Gambaran

3. Instalasi Perangkat
Catatan:
1. Jika sistem tidak memulai instalasi secara otomatis, Anda dapat menjalankan
program melalui My Computer> PROLiNK 4G.
2. Drivers perangkat Anda akan terinstal di waktu yang sama.
PRT7007L mendukung tiga modus kerja.
i. Modus USB – Koneksi melalui kabel USB
• Koneksikan perangkat Anda ke klien dengan kabel USB.
• Hidupkan perangkat Anda.
• Ikuti sistem untuk menyelesaikan instalasi perangkat lunak.
• Setelah instalasi, sistem akan membuat ikon shortcut pada
desktop Anda. Double klik pada shortcut dan akan membawa
Anda ke konfigurasi Web halaman PRT7007L.
Kecuali Anda perlu mengubah pengaturan 3G/4G atau mengakses
pengaturan lanjutan dari perangkat, Anda dapat mengakses Internet
tanpa perlu mengkonfigurasi perangkat.
Modus koneksi WAN adalah "otomatis" secara default.
ID 4

ii. Modus WiFi – Koneksi melalui WiFi
Hidupkan perangkat Anda secara langsung.
Ini akan memakan waktu 1 ~ 2 menit untuk menginisialisasi.
Gunakan aplikasi WiFi normal pada klien untuk mencari nirkabel
yang tersedia pada jaringan.
Pilihlah SSID dari perangkat Anda (Default SSID adalah
PROLiNK_PRT7007L_xxxxx), lalu klik konek. Default password adalah
prolink12345.
Modus koneksi WAN adalah "otomatis" secara default. Anda dapat
mengakses Internet tanpa perlu mengkonfigurasi perangkat.
Jika Anda perlu mengubah pengaturan 3G/4G atau mengakses
pengaturan lanjutan dari perangkat, lihat "Mengakses halaman
konfigurasi WebGUI"
3. Instalasi Perangkat
ID 5

4. Web-based Conguration
iii. Modus Campuran – Koneksi melalui WiFi dan USB
Ini adalah kombinasi dari menggunakan kabel USB dan Wi-Fi.
Masukkan password default "password", lalu klik Login untuk
mengakses halaman konfigurasi WebGUI.
ID 6
Mengakses Halaman Konfigurasi WebGUI
Pastikan sambungan antara perangkat Anda dan klien aktif. Jalankan
Internet browser dan masukkan http://192.168.123.1 atau
http://p.home
Halaman login akan muncul sebagai berikut.
3. Instalasi Perangkat

ID 7
Pilih Settings > Network Settings Ubah Mode Koneksi, pilih
Network atau ubah
pengaturan APN.
Pilih Settings > Wi-Fi Settings Mengubah pengaturan
jaringan nirkabel dasar, pilih
Modus keamanan dan jenis
WPA, dan melakukan
konfigurasi WPS.
Pengaturan
Setelah login, Anda juga dapat memilih Settings, dan melakukan
operasi berikut.
Pengaturan Cepat
Setelah login, pilih Settings > Quick Settings, dan kemudian wizard
Pengaturan Cepat akan muncul.
Wizard Pengaturan Cepat akan memandu Anda tentang pengaturan
parameter dasar untuk perangkat dengan cara yang paling aman.
Setelah prosedur ini, Anda dapat menggunakan layanan Internet
Anda.
4. Web-based Conguration
Catatan:
Jika Anda memilih APN Manual, silakan berkonsultasi dengan ISP Anda apa nama
APN harus dimasukkan.

4. Web-based Conguration
Pilih Settings > Device Settings Mengubah pengaturan
Administrator, memulihkan
standar pabrik, mengelola
PIN atau mengatur konfigurasi
antarmuka LAN.
Pilih Settings > Firewall Pengaturan Mac / IP / Port
Filtering, Port Forwarding atau
konfigurasi Sistem Keamanan.
Pilih Settings > Router Settings Ubah LAN Router IP dan
pengaturan DHCP.
Pilih Settings > Internet Wi-Fi Terhubung ke Hotspot sebagai
repeater Wi-Fi.
ID 8
Mengaktifkan 2.4GHz / 5GHz Dual Band
i. Menu settings > Wi-Fi Settings > Basic Settings, klik Enable untuk
Multi SSID Switch dan klik Apply