Promise F29000020000101 User manual

1
Support ange on
the front end of
each rail
Front right label
Front left label
Guide pins on rails align with holes in the rack post
Installing the rails onto the rack
Rail Kit SpecificationS
Rack Type Use with 19” equipment rack
adjustable length 600~900 mm (post to post)
Shipping Package Dimensions 370*380*740 mm
Shipping Weight 28 kg
Suitable Devises 3U and 4U enclosure hardware designed for 19” rack
Cautions
• Donotpopulateanyunitwithharddrivesuntilithasbeensecurely
installedintherack.
• Atleasttwopersonsarerequiredtosafelylift,place,andattach
theenclosurehardwareunitintoaracksystem.
• Donotliftormovetheenclosurehardwareunitbythehandles,
powersuppliesorthecontrollerunits.Holdthesystemitself.
• Donotinstalltheenclosurehardwareunitintoarackwithoutrails
tosupportthesystem.
• Onlyaqualiedtechnicianwhoisfamiliarwiththeinstallation
procedureshouldmountandinstalltheenclosurehardwareunit.
• Mounttherailstotherackusingtheappropriatescrewsandange
nuts,fullytightened,ateachendoftherail.
• Donotloadtherailsunlesstheyareinstalledwithscrewsas
instructed.
• TherailsavailableforthePROMISEenclosurehardwareunitare
designedtosafelysupportthatPROMISEenclosurehardwareunit
whenproperlyinstalled.Additionalloadingontherailsisatthe
customer’srisk.
• PROMISETechnology,Inc.cannotguaranteethatthemountingrails
willsupportyourPROMISEenclosurehardwareunitunlessyou
installthemasinstructed.
pacKage liSt
• Rail Kit Part Number: F29000020000101
• Content of Rail Kit: 1 Pair of Supporting Rail Kit
Rail Kit installation of VtRaK/Vess/PegasusPRo 3u/4u enclosuRe
To install the enclosure hardware into a rack with the supplied mounting rails:
1. Checkthetofthemountingrailsinyourracksystem.
2. Adjust the length of the mounting rails as needed.
• The rear rail slides inside the front rail. The rail halves are riveted together and use no
adjustment screws.
• The front-left and front-right mounting rail ends are labeled.
• Be sure the front rail support is on the bottom facing inward
• All rail ends, front and rear, attach at the outside of the rack posts.
• The guide pins at the rail ends align with the holes in the rack posts.
• Usetheattachingscrewsandangenutsfromyourracksystem.Tightenthescrewsand
nuts according to instructions for your rack system.
Mounting the enclosure hardware in a19” rack
The instructions here apply to VTrak, Vess and PegasusPro 3U and 4U enclosure hardware. The
sliding rail rack mounting hardware is the same for both form factors.

2
Rail ends attach on the
outside of the front and
rear rack posts
Rail ends aach to the outside of each post
Rails installed
and tightened
Brackets
3U/4U enclosure
Placing the system onto the rack rails
Screws and ange nuts attach
the enclosure to the rack posts
Secure to rack
Brackets mount outside the rack post Mounting rails
mount outside the
rack post
Vertical rack post
System installed in rack
3. Place the enclosure hardware onto the rails.
• At least two persons are required to safely lift the system.
• Lift the enclosure hardware itself. Do not lift the system by its brackets.
4. Secure the enclosure hardware to the rack.
• Theunitattachestotherackpostsusingtheincludedscrewsandangenuts.Onescreweach
side, in the upper hole only.
• Usetheattachingscrewsandangenutsthatcamewiththeenclosurehardware.