Christie 38-804785-01 User manual

Universal flat-panel mount
I N S T A L L A T I O N M A N U A L
www.christiedigital.com
PM ©2004/ REV 02

- 2 -
- Assembly drawing
- Fine tune tilt adjustments
- Parts list
- Installing the adapter plate
- Horizontal or vertical mounting
- Finding the wood studs behind the wall structure
- Securing the wall brackets to the wall
- Securing the flat panel to the wall mount
Contents
WARNING: Safety precaution measures must be practiced at all times during the installation of this product. Use proper safety gear and
tools for the installation procedure to prevent personal injury.
The entire installation instructions should be fully read and understood, including all of the safety symbols and safety precautions, before
beginning installation. The installation instructions should be read, understood and followed to prevent personal in
j
ur
y
or propert
y
dama
g
e.
Keep these installation instructions in an easily accessible location for future reference.
Indicates that the power plug is to be disconnected from
the power outlet.
Safety precautions must be taken at all times.
Contact Christie for an
y
q
uestions
Warning and caution in general
A secured structure wooden stud wall must always support the weight or load of the flat panel. Always confirm the center of the wood
stud before beginning the installation.
Do not install in locations where there is vibration, movement or danger of impact. Failure to do so could result in flat panel cracking or
falling from the wall causing damage and injury.
Do not install near heater, fireplace, direct sunlight or air conditioning or any other source of direct heat energy. Failure to do so may
result in damage to the flat panel and could cause a risk of fire.
At least two qualified people should always perform the installation work. Injury and damage can result from dropping or mishandling
the flat panel.
Mounting structure recommended wood studs, solid-flat concrete. Use a min dia of 5/16” x 2 ¼” lg concrete wedge anchor
(commercially available). or a min dia of 5/16” x 3” lg wood screws.
The wall structure must be capable of supporting at least five (5) times the weight of the flat panel. If not, the wall must be reinforced.
Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could
result in serious personal injury.

- 3 -
7.100
7.100
14.200
4.375
11.000
15.500
Ø2.375
7.690
15.317
20.000
24.000
Ø0.4061.411
17.000
2.964
4.905
5.058
Description
A
. Wall plate
B. Mounting brackets
C. Griplate™
D. Mounting hardware
E. M6 x 30 (mm) Phillip screws
F. Wood stud
G. 5/16” x 3” Lag screws and flat washers
H. Safety knobs
Assembly drawing
Dimensions are in Inches
Fine tune tilt adjustments
1. M5 Phillips screws for fine tension
2. M8 Hex nut coarse tension
NOTE: The 8 (mm) hex nut is for your coarse
tension adjustment and the 5 (mm) screws are for
your fine tension adjustment.
A
B
C
D
E
F
G
H
H
G
1
2

- 4 -
Parts list (con’t)
Level (1)
M6 x 12 Safety knobs (2)
5/16" flat washers (6)
5/16" x 3" Lag bolts (6)
(used on wood studs only)
Griplates™ (4)
Wall plate (1)
Mounting brackets
(left & right)
M6 x 30 Lateral shift
locking screws (2)
All of these parts are used to install the mounting bracket. Make sure that none of these parts are missing before beginning installation. If there
are parts missing stop the installation and contact Chritie.
M5 x 12 phillip
screws (4)
M6 x 12 phillip
screws (4)
A
da
p
ter
p
late
(
1
)

- 5 -
Installing the adapter plate
Invert your flat panel and lay it gently on a soft and flat surface so
no damage will occur. Align the adapter plate with the four (4)
outer mounting points on the back of the flat panel, and then
secure it by using the four (4) M6 X 12 phillips head screws and
flat washers (supplied). See figure 1.
WARNING!
INVERT THE FLAT PANEL AND PLACE IT ON A SOFT, FLAT SUFRACE TO PREVENT DAMAGE TO THE FLAT PANEL. USE A BLANKET, FOAM, ETC.
FAILURE TO DO SO WILL RESULT IN DAMAGING THE FLAT PANEL. DO NOT LAY THE PLASMA ON THE FLOOR WITHOUT ANY PROTECTION TO
THE GLASS. THE FLAT PANEL IS HEAVY AND FRAGILE. AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR
INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE
FLAT PANEL.
WARNING : Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could
result in serious
p
ersonal in
j
ur
y
and
p
ossible dama
g
e to the flat
p
anel.
M6 x 12 Phillip
screws
Blanket, foam etc.
Flat surface
Adapter plate
Flat washers
Inverted flat
p
anel

- 6 -
1/8"
1/8"
Horizontal or Vertical mounting
Horizontal mounting
Vertical mounting
To mount your flat panel horizontally, secure the two (2) mounting brackets to the
adapter by securing them with the four (4) grip plates and four (4) M5 X 12 phillip head
screws. Place the grip nipples facing down on the bottom of the mounting bracket and
facing up on the top. Pre-install at least 1/8” of thread into the two (2) M6 x 30 Phillip
screws to the right and left mounting brackets.
See figure 2 and 3.
Soft &n flat
surface
Left & Right brackets
Griplates™
M5 x 12 Phillip screws
Inverted flat panel
Soft & flat
surface
Inverted flat panel
Left & Right brackets
Griplates™
M5 x 12 Phillip screws

- 7 -
16"
CENTEROFVIEWINGHEIGHTDESIRED
16"
Finding the wood studs behind the wall structure
Using a (commercially available) wood stud finder, locate
the 16" stud centers behind the wall. Once found, make a
pencil marking on the center of the wood studs.
See figure 4.
Place the wall plate to the reference line and mark the six
(6) lag bolt mounting points through the wall plate slots on
the wall. Level the wall plate with the reference arrow
pointing up to the ceiling.
See figure 5.
Mark the wall and
the center of the
wood studs.
Wood stud finder
(commercially available)
Mark the six (6)
mounting slot
openings
Wood studs
behind the wall
structure
Center of
viewing mark
NOTE: The wall plate has 16" mounting slot
positions.
(Look at the assembly drawing on page 3)
Level

- 8 -
16"
Securing the wall bracket to the wall
Drill six (6) ¼" pilot holes to the marked wall.
See figure 6.
Level and secure the plate to the wall with the
reference arrow facing up to the ceiling. Secure the
plate using the six (6) 5/16" lag bolts and flat
washers (supplied).
See figure 7.
(
6
)
Pilot holes
Drill gun

- 9 -
WARNING: AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO
COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL.
Securing the flat panel to the wall mount
Make any lateral shift adjustment and lock it by
tightening the two (2) M6 x 30 (mm) Phillips screws
found on the bottom of the mounting brackets.
CAUTION: Do not over tighten the M6 screws to
the rods.
See figure 9
Raise the flat panel with the LEFT and RIGHT mounting brackets secured to the flat
panel and insert the top and bottom hooks from each bracket to the rods from the
wall plates. See figure 8.
TOP
BOTTOM
Lateral shift
M6 x 30 Lateral
shift screw
M6 x 30 Lateral
shift screw

- 10 -
Tilt the flat panel and secure the two (2) M6 x 12(mm) safety
knobs to each of the mounting brackets.
See figure 10
Securing the flat panel to the wall mount
NOTE: To remove the display from the wall simply extend the display to its maximum tilt range, remove the two 6 (mm) safety knurl knobs push
the flat panel back to it’s flat position loosen or remove the two (2) M6 x 30 lateral shift screws and lift the unit of the wall.
M6 x 12
Safety knobs

- 11 -

- 12 -
PM©2004
www.christiedigital.com