Promounts Apex UA-PRO640 User manual

IMPORTANT! For safety reasons, the concrete wall must be
capable of supporting the combined weight of the mount
and the display.
INSTRUCTION MANUAL
Display Size: 37” to 100”
Maximum Load: 68 kg (150 lbs)
Mounting Pattern: 600 mm x 400 mm (23.6” x 15.7”) max
Tilt Range: 2° up to 10° down
Pan/Swivel Range: up to 180°
Prole: 7.1 cm to 64.3 cm (2.8” to 25.3”)
Read these instructions before you begin. If you are
unsure of any part of the process, contact a professional
contractor or installer for assistance. Improper installation
can result in injury or damage.
The wall or mounting surface must be capable of
supporting the combined weight of the mount and the
display; if not, the structure must be reinforced.
Locate pipes, wires, or any other hazards in the wall where
you wish to install the mount before drilling.
Safety gear and proper tools must be used. Failure to do so
can result in injury or damage.
Two people are recommended for installation. Do not
attempt to lift a heavy display without assistance.
Follow all instructions and recommendations regarding
adequate ventilation and suitable locations for mounting
your display. Consult the owner‘s manual for your particular
display for more information.
1
2
3
4
5
6
IMPORTANT! The mount must be secured to at least two
wood studs no less than 16”apart. The studs must be capable
of supporting the combined weight of the mount and
display.
Part 1A – Mounting to the Wall (Drywall)
3
4
5
SPECIFICATIONS
BOX CONTENTS
HARDWARE KIT
TOOLS REQUIRED
INSTALLATION
WARNINGS
WARNINGS (continued)
Phillips Head Screw Driver
Ratchet or Driver with a 1/2” Socket
Electric or Portable Drill
1/4” Drill Bit and Stud Finder for Drywall Installation
3/8” Masonry Bit for Concrete Installation
Level
Mount (x1)
Mount Arm (x2)
Instruction Manual (x1)
Hardware Kit (x1)
Part 1B – Mounting to the Wall (Concrete)
1Place the mount against the wall in the desired location
with the arrow on the mount pointing up. Make sure it is
level.
Fig. 1
Fig. 2
Use a high quality stud finder to locate two studs on the
wall where you wish to install your mount. Mark both
edges of each stud to help identify the exact center.
NOTE: Use the center of each stud to avoid cracking or
splitting the wood.
Place the mount against the wall over the marked studs
with the arrow on the mount pointing up. Make sure it is
level.
While another person holds the
mount in place, mark four
locations (two per stud) for
securing the mount to the wall
(see Fig. 1).
Set the mount aside and drill a
1/4” pilot hole at each marked
location.
Attach the mount to the wall
with the arrow pointing up using
the lag bolts (A) and washers (B)
provided (see Fig. 2). Do not
release the mount until all bolts
are secure. Ensure that the
mount remains level.
1
2
CAUTION: This wall mount is intended for use only with
the maximum weight of 150 lbs. Use with heavier than
the maximum weights indicated may result in instability
causing possible injury.
FULL-MOTION WALL MOUNT
UA-PRO640
(A) M8 x 63 Lag Bolt (x4)
(B) Lag Bolt Washer (x4)
(C) Concrete Anchor (x4)
(D) M4 x 15 Screw (x4)
(E) M5 x 15 Screw (x4)
(F) M5 Washer (x4)
(G) M6 x 15 Screw (x4)
(H) M8 x 15 Screw (x4)
(I) M8 x 30 Screw (x4)
(J) M8 x 50 Screw (x4)
(K) M8 Washer (x4)
(L) Small Spacer (x4)
(M) large Spacer (x4)
BY
FOR LCD, PLASMA, and LED DISPLAYS

2
3
4
5
Part 2 – Attaching the Mount Arms to the Display (continued)
0153-20191021
OPERATION AND ADJUSTMENT
A
Fig. 3
Fig. 4
NOTE: This mount comes with a variety of screw lengths and
diameters to accommodate different display models. Not all of
the hardware in the kit will be used. If you cannot find the
appropriate screw size in the kit provided, consult with the
manufacturer of your display or a professional installer.
Part 2 – Attaching the Mount Arms to the Display
IMPORTANT! Use extra care during this part of the installation
to avoid damaging your display.
Part 1B – Mounting to the Wall (Concrete) (continued)
While another person holds the
mount in place, mark four
locations for securing the mount
to the wall (see Fig. 3).
Set the mount aside and drill a
3/8” hole at each marked location.
Remove any excess dust from the
holes.
Insert a concrete anchor (C) into
each hole so that it is flush with
the concrete surface (see Fig. 4). A
hammer can be used to lightly tap
the anchors into place if
necessary.
Attach the mount to the wall with the arrow pointing up
using the lag bolts (A) and washers (B) provided (see Fig. 3).
Do not release the mount until all bolts are secure. Ensure
that the mount remains level.
A
B
Attach the mount arms to the back of your display using
the screws identified in steps 1 and 2 (see Fig. 5):
If you are using the M4 and M5 screws you will need to
use the M5 Washers (F). If you are using M6 and M8
screws, you will need to use the M8 washers (K).
If you are using the longer screws, you may also need to
use spacers (L or M).
If the back of your display is flat and the mounting holes
are flush with the surface, use the shorter screws (D, E G
or H) from the hardware kit.
BIf the back of your display is curved or if additional space
is needed between the display and the mount, use the
longer screws.
2Determine the correct diameter of screw to use by carefully
trying one of each size (M4, M5, M6 and M8) from the
hardware kit. Do not force any of the screws – if you feel
resistance stop immediately and try a smaller diameter
screw.
1Determine the correct length of screw to use by examining
the back of your display:
2
3
IMPORTANT! The latches must be closed and locked at
all times to prevent the display from being accidentally
knocked from the mount.
IMPORTANT! Never fully loosen or remove the level
correction nuts.
1
2
3
4
To change the tilt angle of
your display, have one
person hold the display
firmly in place while
another person loosens
the tilt knob (see Fig. 7).
Once loosened, move your
display to the desired
position, and then
re-tighten the knob.
Do
not release the display until the knob is fully tightened.
Swivel adjustments can be made by moving the display
to the desired position. Be careful that fingers or cables do
not get pinched when moving the mount.
Level correction
adjustments can be made
by rotating the display in
the needed direction. If it
is too difficult to turn the
display or if the display
does not stay in position,
adjust the tension of the
two wing nuts located
behind the faceplate.
Adjust the two nuts evenly (see Fig. 8).
1With the help of another person, carefully lift your display
and place it on the mount. Do not release the display
until the mount arms have
securely hooked onto the
mount.
Close the safety latch at the
bottom of each arm. Each
latch will automatically lock
when fully closed (see Fig. 6). Periodically clean your mount with a soft, dry cloth. Inspect
all screws and hardware at regular intervals to ensure that
no connections have become loose over time. Re-tighten
as needed.
Cables can be routed through the channels located on the
bottom of the mount. Make sure none of the cables can be
pinched during operation of the mount.
Part 3 – Final Assembly
3
Fig. 5
For displays
with curved or
recessed backs.
For displays with
at backs.
Fig. 8
Fig. 6
Fig. 7
Level correction nuts