Proper iPad Wall Mount User manual

iPad Wall Mount
Installation Guide

1
Power
This product includes a (2m) 8-Pin Lightning to USB cable.
Before installation, ensure your device is within reach of
a power source. If you are plugging your iPad directly into
a wall outlet, it is recommended that you use the ocial
Apple Power Adapter included with your iPad, or a genuine
replacement from Apple.
Cable Management
Before installation, consider the route your cable will need to
take to reach a power source. Try to keep the cable away from
any potential hazards or spills. You have the choice of either
i. running the power cable out of the bottom of the mount,
which will not require the cable to pass through the wall, or,
ii. tunneling the power cable through the wall, which requires
a Ø 15-25mm hole in the wall for the cable to pass through.
Drilling
If you choose to tunnel the cable through your surface, you
will need to make a Ø 15-25mm hole for the charging cable to
pass through. Consider if your surface is suitable for this, and
if possible, use a licensed professional.
Loosening and Tightening Screws
Overtightening the screws may cause damage to the wall
mount, or your device. If you feel as though something isn’t
tting together correctly for any reason; rst re-read the
instructions to ensure you haven’t missed anything, then
contact our customer support team for further assistance.
Additional Components
As the Wall Mount can be mounted onto a variety of
surfaces, we are unable to provide certain hardware to
assist in mounting to every wall. You will need to source the
appropriate tools for your particular use case.
Safety Notice
Please read carefully the important safety notice on page 7
before you begin drilling into your wall.
More Information
If you require any assistance, visit our helpdesk:
> help.studioproper.com
or contact our customer support team with any questions:
> [email protected]
Before You Begin

3
Product Overview
Apple iPad
This product is designed to be compatible with
Apple iPad (5th & 6th Generation).
(Not included with the stand)
Powered iPad Lock Belt
This is the ‘belt’ that secures your iPad in place,
conceals the charging cable, and keeps your device
securely attached to the wall mount.
Wall Mount
The main body of the Wall Mount.

4
Use the Security Tool for star
shaped screws like this.
Use the Hex Key for hexagonal
screws shaped like this.
The Toolkit
The Pick Tool is used to
lift o end caps.
Security ToolHex Key / Pick Tool

5
Mounting Options
Tail
Tailing your cable from the bottom
of the stand requires you to feed the
cable through the stand before you
secure it to the wall.
Tunnel
Tunneling your cable through the
wall requires you to make a hole
(Ø15-25mm) beneath the stand.
i. ii.

6
Additional Components
Spirit Level
Used to perfectly align the Wall
Mount to the wall before drilling.
Hole Saw (Ø15-25mm)
Required only if you have choosen
to tunnel your charging cable
through the wall.
Cordless Drill
Installation requires drilling into
your wall.
Screws
Consider the best option for your
wall. ‘Self-Tapping Screws’ are
suitable for most common surfaces.
These components are not included, but are required for installation.
As the Wall Mount can be mounted onto a variety of surfaces, we are unable to provide certain
hardware to assist in mounting to every wall. You will need to source the appropriate tools for your
particular use case.

7
Safety Notice
As this product requires drilling into the wall, ensure you
take into consideration the possibility of live power, gas
lines, water lines, or other plumbing and utility hazards.
Interference with the mains electricity can result in death.
If you are in any way uncertain about the safety of the
surface you are mounting to, we recommend consulting
a licensed professional installation contractor.

8
1.
2.
Use the Pick Tool to lift o the metal
end caps from the Lock Belt.
Use the Security Tool to remove the 4
screws holding the cassette in place.
1
2

9
3.
4.
Use the Security Tool to remove the 2
screws holding the end cap on.
Position the iPad into the frame and
tighten with the security screws.
Note: Ensure the Lightning port is
aligned in the correct orientation.
(See Home button indentation)
3
4

10
5. Using the Hex Key, remove the
4 screws holding the Lock Belt frame
to the body of the Wall Mount.
5

11
6a.
6b.
On your wall, measure out and mark
the points where you will be drilling.
Note: We recommend using a spirit
level for perfect alignment.
If you intend to tunnel the charging
cable through the wall, you must also
make a 15-25mm hole in the centre of
the mounting position.
If not, you may skip this step.
Note: Read carefully the Safety Notice
on page 7 before drilling into the wall.
6a
6b
50mm
Ø15-25mm
25mm

12
7. Screw the Wall Mount into the wall.
Note: As the Wall Mount can be
mounted onto a variety of surfaces,
we are unable to provide certain
hardware (such as screws) to assist in
mounting to every wall. You will need
to source the appropriate tools for
your particular use case.
If you are in any way unsure, consider
contacting a licensed professional.
7

13
Using the Hex Key, re-attach the 4
screws holding the Lock Belt to the
body of the Wall Mount.
8.
8

14
Connect the Lightning cable to the
iPad. There are clips underneath to
hold it in place.
Pass the USB end of the cable through
the wall mount.
9.
10.
10
9

15
Use the Security Tool to attach the
iPad to the frame.
11.
12. Push the end caps back onto the frame
to secure the iPad in place.
11
12