Protector Aluminium Slat Screen Kit User manual

Aluminium
Slat Screen Kit
Installation guide
Contents of each kit:
1800 mm W x 1200 mm H
» 15 x Slats – 1795 mm W
» 2 x Slat Channels – 1200 mm H
» 2 x Cover Strips
» 2 x Slat Channels Caps
» 34 x Screws – 15 mm
» 2 x Slat Spacer Tools

900 mm W x 1766 mm H
» 22 x Slats – 895 mm W
» 2 x Slat Channels – 1766 mm H
» 2 x Cover Strips
» 2 x Slat Channels Caps
» 48 x Screws – 15 mm
» 2 x Slat Spacer Tools

2000 mm W x 1766 mm H
» 22 x Slats – 1995 mm W
» 2 x Slat Channels – 1766 mm H
» 2 x Cover Strips
» 2 x Slat Channels Caps
» 48 x Screws – 15 mm
» 2 x Slat Spacer Tools

2350 mm W x 308 mm H
» 4 x Slats – 2345 mm W
» 2 x Slat Channels – 308 mm H
» 2 x Cover Strips
» 2 x Slat Channels Caps
» 12 x Screws – 15 mm
» 2 x Slat Spacer Tools
SLATS
SLAT
CHANNELS
CAP
SCREWS
SLAT
CHANNEL
COVER
STRIP
SLAT SPACER TOOL
65mm
16mm
32mm
27.5mm 32mm
4.8mm
IMPORTANT INFORMATION
This product is intended for use as decorative
Screening only (“the Intended Use”). This product
is not suitable for areas protecting a fall of 1 metre
or more, nor is it suitable for use as pool fencing,
balustrading, or for other structural applications.
Consult with your local building authority to
determine product suitability before commencing
works with this product. You must use this product
in accordance with all applicable laws and
regulations and for the Intended Use. It is your
responsibility to check with your local authorities on
all relevant laws and regulations relevant to use of
this product. Incorrect use or misuse of this product
could potentially result in loss, damage, injury, or
even death. The customer assumes to the maximum
extent permitted by law, all the risks inherent in
the use of this product, including the risk of serious
injury, death or damage to property resulting from
use of the product, regardless of how such death,
injury or damage was sustained and in all cases
where the product has been used other than for the
Intended Use.
Warranty
Our goods come with guarantees that cannot be
excluded under the Australian & New Zealand
Consumer Laws.You are entitled to a replacement
or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
In addition to these guarantees and for your peace
of mind, we also offer a 10 year warranty on our
product. This warranty is subject to our terms and
conditions.You can access the full terms and
conditions of this warranty here:
www.protectoral.com/warranty/garden/
You should read these terms and conditions in full
prior to purchase of this product. By purchasing this
product you accept our terms and conditions of the
warranty.
COVER
STRIP
SLAT
CHANNEL
SLAT
Optional if cutting
, Circular saw, Hacksaw or
Angle Grinder
All you require:
Optional if cutting, Circular Saw or Hacksaw

Aluminium Slat Screen Kit Installation guide - 2023v1
Step 1: Position the First Slat
Place your first Slat inside the Slat Channels, aligning with the
bottom of the Channel.
Step 2: Check and Fix the Slat
Ensure the Slat is level, the Slat Channels are square, and the
Slat Screen width is correct before fixing the first Slat with 4 of
the provided screws (2 on each side).
Step 3: Insert the Next Slat
Slide the next Slat into the Slat Channels from the top down.
Use the 2 x 16 mm spacers provided (1 near each Slat Channel).
Step 4: Repeat Steps 2 and 3
Continue repeating Steps 2 and 3 until all required Slats are fitted.
Step 5: Attach Cover Strips
Clip the Cover Strips onto the Slat Channels to hide the screws,
starting from the bottom and working your way up.
Step 6: Add Slat Channel Caps (if needed)
Insert the 2 x Slat Channel Caps.
Your Aluminium Slat Screen
is now fully assembled.
16mm space
For fixing your Aluminium Slat Screen to a post or structure,
consider using Protector Al Garden Posts and/or Screen
Fixing Brackets for a matching powder coat finish.
Note: These cannot be installed on the channel cover strip
Important: 1 Screw per Slat, per side. 2 Screws per side
only required for first and last Slats.
Scan QR Code to use our simple Measurement Calculator
or go to www.protectoral.com.au/products/slat-screens
IMPORTANT: Read these steps from start to finish BEFORE beginning assembly.