WamBam Yard & Pool Vinyl Gate User manual

REALLY
Yard & Pool
Vinyl Gate
Important stuff to know about
installing your WamBam gate.
1-877-778-5733
www.wambamfence.com
Ver 1, May 2013

1
1 - Read Over Fence Instructions First
Your gate and fence will work better together as an integrated
solution if you rst take the time to read and understand your
fence instructions.
2 - Do a Dry Run First on the Gate Frame
Only (not pickets or boards)
Please do not glue or screw your gate frame together until you
have rst temporarily assembled the gate. In other words,
do a dry run rst.
This will ensure three things:
a) That you have everything necessary to complete the gate.
b) That you will have assembled the gate in the correct order.
c) All the pieces t and function properly.
It’s easier to trouble shoot when things are not glued and screwed together.
After you assemble your gate correctly, please disassemble as necessary and
use glue and screws to permanently assemble the gate.
3 - Ideally, Install Your Gate Posts
Before Your Fence Posts
Your fence panels will be more forgiving for a custom t than
your gate. Ideally, position and install your gate posts
before you do anything else, or very early on in the
process of setting up your fence run.
Install Your Gate Posts
Before Installing Your
Fence Posts.
Reality Check
Yard & Pool Vinyl Gate
For more information,
contact us at 1 877-778-5733.

2
4 - Ideally, Do Not Hang Your Gate System Off a Single
Non-Supported Post.
Your gate will perform better and last longer if your hinge post is connected to a panel of fence which is
connected to another post. The weight strain will be transferred unto two posts versus just one. Installing
fence panels on both sides of your gate is the ideal in all situations. If this is not possible because of space
restrictions, please contact us for alternative solutions to overcome.


For more information, contact us at 1 877-778-5733.
Do Not Hang Gate on Lone Soldier Post.
Yard & Pool Vinyl Gate
Pool Code Notes
For swimming and other child safety gates, most safety standards specify:
a) Your fence height needs to be between 4’ and 6’ high minimum
b) Your gate needs to open outwards away from the pool
c) Latch releasing mechanism to be minimum 54” o the ground.
*The Yard & Pool gate will require a specialized latching system to meet pool code.
Use MagnaLatch Top Pull Hardware (not included).
Magna Latch Top Pull Code is # MLTPS2BGA.
*Always conrm these and other requirements with the appropriate authorities in your area.
Code will change from one location to another across the country.

Gate Brace Warning
The gate brace included with this gate may be considered a climbing surface by some pool inspectors
and therefore in conict with pool code. This gate can be assembled and installed without the brace if
and when necessary.

3
Box Contents
Yard & Pool Vinyl Gate
For more information, contact us at 1 877-778-5733.
Posts Sold Separately as 2-Packs
.090in.wall
thickness
Each Gate Box Includes:
• Top Rail (1)
• Gate Hinges (2)
• Pickets (8)
• Arch Brackets (2)
•
Gate Latch (1)
• Vertical Stiles (2)
• Stainless Steel Screws (16)
• Gate Bottom Brackets (2)
• Bottom Rail (1)
Sold Separately:
• 6ft. Posts (2-Pack)
.050in.wall
thickness
• Tube of Glue (1)
• Gate Brace (1)

PRODUCT OVERVIEW
For more information, contact us at 1 877-778-5733. 4
Yard & Pool Vinyl Gate
Posts Sold Separately
Ground
7.75in.
48in.
3.5in.
41.5in.
56.84in.
1.5in.
3.5in. 3.5in.
1.5in.
2in.
22in.
58.84in.
52in.
50in.
54.5in.
Gate InstallationGate Assembly
B
A B
CD
3.5in.
1.5in.
.090in. wall thickness
C
1.5in.
D
3.5in.
A
1.5in.3.56in.
36in.
10in.
20in.
Concrete Footing

For more information, contact us at 1 877-778-5733. 5
Assemble the Gate Frame Bottom & Sides
STEP 1
Detailed Installation Instructions
Yard & Pool Vinyl Gate
Completely assembled gate shown A - Run bead of vinyl weld continously around
the inside of the gate bracket
D - Insert vertical gate stiles. They will BOTTOM OUT
against bottom horizontal rail
C D
B
Note that the bottom rail
is Ribbed internally.
GLUE
GLUE
Did you do a dry run of assembly first?
Please read page 1 of instructions.
GLUE
Handle with care: vinyl weld
glue takes approximately
five minutes to cure.
A
C - Insert the bottom rail ALL THE WAY until it
BOTTOMS OUT INSIDE GATE BRACKET
B - Insert the bottom rail ALL THE WAY until it BOTTOMS OUT inside gate bracket
IMPORTANT!
Insert fully to this point.
Insert fully to this point.
Fasten gate brackets to internal
members though inside
of frame using screws.

For more information, contact us at 1 877-778-5733.
6
Yard & Pool Vinyl Gate
Insert Pickets & Assemble
the Gate Frame Top
STEP 2
Did you do a dry run of assembly first?
Please read page 1 of instructions.
Insert pickets in the proper
order according to their height
as shown above.
A
A - Run bead of vinyl weld continously around
the inside of the gate bracket B - Insert the top rail until it bottoms out inside arch bracket
E - Insert pickets in the proper order through
holes in the bottom rail
F - Slide gate arch (with brackets) over the
pickets and vertical gate stiles
E
B
F
C
C - Insert the top rail until it bottoms out inside
arch bracket D - Run bead of vinyl weld continously around the inside of the gate bracket
D
GLUE
GLUE
GLUE

For more information, contact us at 1 877-778-5733. 7
Screw Gate Frame/Brackets
STEP 3
Yard & Pool Vinyl Gate
A
A - Screw into brackets as necessary

For more information, contact us at 1 877-778-5733. 8
Fasten Gate Hinges
& Gate Latch
STEP 4
Yard & Pool Vinyl Gate
A
A - Fasten gate hinges and gate latch onto the gate brackets with SHORT screws
For swimming and other child safety gates, most safety standards specify:
a) Your fence height needs to be between 4’ and 6’ high minimum
b) Your gate needs to open outwards away from the pool
c) Latch releasing mechanism to be minimum 54” off the ground.
*The Plain Jane gate will require a specialized latching system to meet pool code.
Use MagnaLatch Top Pull Hardware (not included) and Captain Morgan Post Caps Only.
Magna Latch Top Pull Code is # MLTPS2BGA.
*Always confirm these and other requirements with the appropriate authorities in your area.
Code will change from one location to another across the country.

(4)
1.25” (#10)
Screws
(2)
.25” Lock
Washers
(2)
.25” Nuts
(2)
.25” x .75”
Hex Bolts
For more information, contact us at 1 877-778-5733.
9
Yard & Pool Vinyl Gate
Gate Brace Parts
B - Ensure that gate is square, then screw
bracing into place.
AB
Assemble & Fasten
Gate Brace
STEP 5
Top Bar Bottom Bar
A - Assemble gate bace
with bolts, washers and
nuts as necessary.
123