ProX SI-X608 User manual

Ver. Q1
All Rights Reserved. Copyright 2020
SI-X608
SI-X608
SI-X608
Quick
Reference
Guide
Pin Assignment
Specifications
LAN1 and LAN2 Port (IN, OUT)
System
Controller EtherCAT Slave Controller
Communication Interface Ethernet
Connector 2 x RJ45 (Support Daisy Chain)
Protocol EtherCAT
Distance between Stations Max. 100m, 100 BASE-TX
Power Supply 9~48 V DC with 3-pin terminal block
LED Indicator Power LED, Green / RUN LED, Green /
Link IN/OUT, Green / Error LED, Red
Installation DIN-Rail
Net Weight 220g
Dimensions (WxHxD) 139.97 x 116.97 x 33mm (without connectors)
Certificate CE/FCC
Environment
Operating Temp. (with airflow) -25°C ~ 75 °C (-13 °F ~ 167°F)
Storage Temp. -40°C ~ 85°C (-40°F ~ 185°F)
Humidity 20% ~ 90%
I/O (Analog Input)
No. of Channels 8
Wire Connection Differential
Input Type Voltage, Current (software selectable)
Range 0~5V, 0~10V, ±10V, ±5V
0~20mA, ±20mA, 4~20mA
Resolution 16-bit
Sample Rate 1k Hz per channel
Accuracy < ±0.2% of FSR
Overvoltage Protection ± 35 VDC
Signal
Pin No.
DC-IN
GND
1
2
3GND_Shield
DC-IN Connector (JPWR1)
4
Signal
Pin No.
TX1+
TX1-
1
2
3RX1+
NC
5 NC
6 RX1-
7 NC
8 NC
4
I/O Connector (JIO1)
Signal
Pin No.
V1+
V2+
V3+
V4+
V5+
Signal
Pin No.
V0-
V1-
1
3
5
7
9
11
13
15
17
19
2
4
6
8
10
12
14
16
18
20
V2-
V3-
V4-
V5-
V6-
V7-
AGND
AGND
V0+
V6+
V7+
AGND
AGND
SI-X608
LINK/ACT IN OUT
PWR RUN ERR
V0+
V1+
V2+
V3+
V4+
V5+
V6+
V7+
AGND
AGND
V0-
V1-
V2-
V3-
V4-
V5-
V6-
V7-
AGND
AGND
SI-X608
INOUT
FGNDGND+VS

SI-X608
Overview
8-Channel Isolated Analog Input EtherCAT Slave I/O Module
Front View Rear View
(Unit: mm)
I/O Terminal Block Pin Assignment
Quick Setup
Safety Precaution
The I/O pins are located
on the lower front section
of SI-X608.
Installing DIN-RAIL Mount
Bottom View
Top View
Notes:
1. It is recommended connecting FGND
PIN to functional earth via a cable.
2. DO NOT connect GND PIN and FGND
PIN of the terminal block together as they
might have potential differences which might
cause signal interferences.
See the notes below
and connect the pins
of the terminal block
properly.
V0+
V1+
V2+
V3+
V4+
V5+
V6+
V7+
AGND
AGND
V0-
V1-
V2-
V3-
V4-
V5-
V6-
V7-
AGND
AGND
35.22
33
139.67
7.41
System Status
Indicators
I/O Terminal
Block
PWR RUN ERR
LINK/ACT
IN OUT
SI-X608
V0-
V1-
V2-
V3-
V4-
V5-
V6-
V7-
AGND
AGND
V0+
V1+
V2+
V3+
V4+
V5+
V6+
V7+
AGND
AGND
Step 1. Use 35mm DIN-RAIL and install it into the
groove located on the rear side of the system.
Step 2. Push the bottom hinge upwards to secure
DIN-RAIL onto the system.
The DIN-RAIL Mount installation is then completed.
1
2
EtherCAT Ports
DC In
FGNDGND
+VS
116.38
INOUT
FGNDGND
+VS
Side View
•
The following messages are reminders for safety on how to protect SI-X608 from damages and extend a long life for SI-X608.
1. Check the Cable Voltage
The range of operating voltage should be DC 9~48V. Otherwise, the SI-X608 module could be damaged.
2. Environmental Conditions
•
•
Install DIN-Rail Mount on SI-X608. Be sure to allow enough space to have easy access around SI-X608.
•Avoid exposure to sunlight for a long period of time or in an airtight space.
•Avoid SI-X608 from any heating device or using SI-X608 when it’s been left outdoors in a cold winter day.
•
of SI-X608.
Avoid moving SI-X608 rapidly from a hot place to a cold place and vice versa because condensation may come from inside
•Don’t place SI-X608 close to any radio-active device in case of signal interference.
3. Handling
Avoid putting heavy objects on top of SI-X608.
•Do not turn SI-X608 upside down.
4. Good Care
•When the outside of the case is stained, remove the stain with a neutral washing agent with a dry cloth.
•Never use strong agents such as benzene and thinner to clean SI-X608.
•If heavy stains are present, moisten a cloth with diluted neutral washing agent or with alcohol and then wipe
thoroughly with a dry cloth.
•If dust has been accumulated on the outside, remove it by using a special vacuum cleaner for computers.
WARNING! Some internal parts of SI-X608 may have high electrical voltage. And therefore we strongly
recommended that qualified engineers can open and disassemble SI-X608.