Pyle Elite PLA3000D User manual

All Pyle products are carefully constructed and thoroughly tested before
shipment. Products purchased in the USA are warranted to be free of defects
in material and workmanship for two (2) years from the date of purchase. This
warranty is limited to the original retail purchase.
Should the product fail due to factory defects in material or workmanship,
your unit will be repaired or replaced at the sole discretion of Pyle.
To obtain warranty service you must first call our Consumer Return Hotline
number at [phone] to obtain a Return Authorization number. This
R.A.# must appear on the outside of your package and on all paperwork
relating to your return.
When returning a product to us for warranty service it must be carefully packed
and shipped prepaid to:
You must also include the following items:
• A copy of your sales receipt or other proof of purchase
• A brief letter indicating the problem you are experiencing
• include in your letter your return address, daytime phone number,
and R.A. number
• also include a check or money order for $18.00 for return shipping,
handling, and insurance, or provide your Visa/MC number with
expiration date.
R.A.#
Pyle Service Center
1600 63rd Street
Brooklyn, NY 11204
Our obligation under this warranty is limited to the repair or
replacement of the defective unit when it is returned to us prepaid.
This warranty will be considered void if the unit was tampered with,
improperly serviced, or subject to misuse, neglect, or accidental
damage.
limited warranty policy
www.pyleaudio.com
amplifiers
Class-D mono block car audio amplifier
user’s manual
PLA3000D

This is due to the noise introduced into the signal by the switching
speed of the power supply, which must be filtered out of the audio
signal.
The power supply incorporated into Pyle Red Elite amplifier is a
DC to DC switching power supply designed to have adequate
headroom for even the most demanding peak and dynamic
range found on today's CDs and recording.
INTRODUCTION...
table of contents
Thank you for purchasing the Pyle Red Elite Class-D amplifier.
Rest assured you have purchased a quality product designed
and engineered to give you many years of uncompromised
musical service.The Pyle Class-D amplifier has been designed
using the latest in electronic technology available today.
This mono subwoofer amplifier is the result of advanced high
speed switching technology that overcomes the less-efficient
Class-D design. the Pyle Red Elite Class-D amplifier reflects
your true appreciation for powerful bass reproduction in the
mobile environment.
This amplifier is designed for low-frequency information only and
it is not capable of reproducing any mid/high-frequency information.
features and specifications
PLA3000D 3-4
protection circuitry and troubleshooting 8
amplifier and installation 7
general features 2
system wiring 5-6
PLA3000D

general features
6
features and controls
Class-D MONO BLOCK AMPLIFIER PLA3000D
speaker connections power terminals
power fuse
protection LED
power LED
sub sonic control
input level control
phase shift switch
line level inputs
low pass frequency control
remote bass boost
3
2
PLA3000D
2400W Mono Block MOSFET Digital Power Amplifier
· Phase Control 0-180 degree
· Remote Bass Control
· Input Impedance : 10K Ohms
· Soft Turn On/Off
· Advanced Protection Circuitry
· S/N Ratio:>90dB
· Heavy Duty Power Coated Heatsink
· Blue LED Level Display
· Dimensions: 10.9"(W) x 2.7"(H) x 15"(L)
PLA3000D
line level outputs
· Mono Block Subwoofer Amplifier
· 1 Ohm Stable1
· MOSFET Power Supply
· PWM (Pulse-Width-Modulation) System
· Glass Epoxy PCB
· Gold Plated RCA Inputs for Line Input & Bypass Output.
· Gold Plated Terminals for Speaker Output and Power Input.
· Thermal, Overload and Short Protection
· Variable Sub-sonic Filter (15Hz~40Hz, 24dB/Octave)
· Variable Low-pass Filter (20Hz~250Hz, 24dB/Octave)

Mono channel amplifier
system wiring
4
features and controls
5
Class-D MONO BLOCK AMPLIFIER PLA3000D
PLA3000D
Class-D MONO BLOCK AMPLIFIER PLA3000D
Low-frequency information for subwoofer only.High efficient power
Stiffly regulated PWM power supplies. MOSFET switches maintain
rated power over a wide range of battery voltages.
Adjustable from 20Hz to 250Hz with a slope of 24dB per octave.This
allows for the adjustment of the upper point of the frequency bandwidth
and the respective subwoofer.
Adjustable from 15Hz to 40Hz with a slope of 24dB per octave.This allows
for the attenuation of frequencies that are mostly inaudible and cause
unnecessary strain on the amplifier.
Protection against thermal, overload and short circuit conditions.
This amplifier come complete with a compact remote GAIN CONTROLLER
which can be conveniently mounted on or under the dashboard of your
car.
Class-D design
power supplies
crossover low pass filter
high pass subsonic filter
protection circuitry
remote dash-mount gain control
power supply voltage
input sensitivity
20Hz-250Hz( 3dB)
250mV~4V Adjustable
14.4V DC Neg.ground(10.5-16V)
dimensions (W x H x L)
mm
inches
input impedance 10K Ohm
10.9 x 2.7 x 15
RMS Power at @4 Ohms
RMS Power at @2 Ohms
RMS Power at @1.3 Ohms
Maximum Power Outputs
400W MONO
800W MONO
1200W MONO
2400W MONO
frequency response
output power @14.4v DC,1KHz
1 Ohm min speaker Impedance
T.H.D 0.1%
S/N ration >90dB
fuse 40A x 2
276x69.5X381
head unit TO SATELLITE AMPLIFIER
LINE INPUT
SIGNAL INPUT AND BYPASS OUTPUT CONNECTION
SPEAKER OUTPUT CONNECTION
L/R Audio
Outputs
subwoofer
MINIMUM
SPEAKER
IMPEDANCE
2~4 OHMS!
PLA3000D
+
-

mounting
amplifier and installation
7
6
to remote turn-on
+12V
head unit 12V battery
system wiring
Class-D MONO BLOCK AMPLIFIER PLA3000D
PLA3000D
fuses
wiring tips
Find a suitable location in the vehicle to mount the amplifier
Make sure there is sufficient air flow around the intended mounting location
Bolt the amplifier to the mounting surface.
Connect the power ground terminal to the nearest point on the chassis of the car. Keep this ground wire less than one meter (39") in length. Use 4 gauge wire.
Connect the remote terminal to the remote output of the head unit using 14 gauge.
Connect an empty fuse holder within 300mm (12") of the battery and 4 gauge or larger high quality cable from this fuse to the amplifier location.
Make sure there is no fuse in this fuse holder. Then make the connection to the "BATT" connection on the amplifier.
If multiple amplifiers are being used, use cables (each with its own fuse at the battery) or a *0 or a *2 cable from the fuse holder at the battery to a distribution block at or near
the amplifier's location.
Connect all line inputs and outputs using high-quality RCA-RCA cables.
Insert fuse(s) at the battery fuse holder(s)
Recheck all connections before powering up.
Set all level controls to their least sensitive positions and set all crossover controls, switches, etc., To the desired frequency or position.
Once the system is powered up, set the volume control on the head unit to about the 2 o'clock position, and then set all the amplifiers' level controls for maximum output level.
Further fine tuning of the various controls may be necessary to obtain the desired results.
POWER INPUT CONNECTION

8
Amplifier will not power up
troubleshooting Protection LED comes on when the amplifier is powered up.
Check for shorts on speaker leads.
Check that the volume control on the head units is turned down low.
Remove speaker leads, and reset the amplifier. if the protection LED still comes on,
then the amplifier is faulty.
Amplifier(s) gets very hot.
Check that the minimum speaker impedance for that model is correct.
Check for speaker shorts.
Check that there is good airflow around the amplifier. in some applications, an external
cooling fan may be required.
Distorted sound
Check that the level control(s) is set to match the signal level of the head unit.
Check that all crossover frequencies have been properly set.
Check for shorts on the speaker leads.
High squeal noise from speakers.
This is always caused by a poorly-grounded RCA patch cord.
Before removing your amplifier, refer to the list below and
follow the suggested procedures.
Always test the speaker and their wires first.
Check for good ground connection.
Check that remote DC terminal has at least 13.8V DC.
Check that there is battery power on the terminal.
Check all fuses.
Check that Protection LED is not lit. If it is lit, shut off
amplifier briefly and then repower it.
High hiss or engine noise(alternator whine) in speakers.
Disconnect all RCA inputs to the amplifier(s)- if hiss / noise
disappears, then plug in the component driving the amplifier and
unplug its inputs. If hiss / noise disappears, go on until the faulty /
noisy component is found.
It is best to set the amplifier's input level as insensitive as possible.
The best subjective S/N ratio is obtainable this way. Try to drive as
high a signal level from the head unit as possible.