Pyle PDJLT50 User manual

Please Read Over This Manual before Operating the Light Fixture
TECHNICAL REFERENCE:
• Extremely small, fast and powerful LED Moving beam.
• DMX Channels: 9/14CH
• Pan/Tilt: 630 /240, speed adjustable
• Smooth electronic dimming:0-100%
• Electronic strobe with pulse and random eects
• High eciency, low power consumption
• Super compact, low weight
• Voltage: 100V-240V,50/60Hz
• Fuse: T6.3A
• Power consumption: 100W
• Light source: 10W LED x 7 (RGBW 4IN1)
• Package: 4PCS/Carton
• Inner Package: 270*220*250 MM
• Out Package: 460*290*520 MM
• N.W.: 12 kg/carton
• G.W.: 14.5kg/carton

1. SAFETY INSTRUCTION
• Please keep this User Manual for future consultation. If you sell the unit to
another user, be sure that they also receive this instruction booklet
• Unpack and check carefully if there is no transportation damage before
using the unit.
• Before operating,ensure that the voltage and frequency of power supply
match the power requirements of the unit
• It’s important to ground the yellow/green conductor to earth in order to
avoid electric shock.
• The unit is for indoor use only. Use only in a dry location
• The unit must be installed in a location with adequate ventilation, at least
50cm from adjacent surfaces. Be sure that no ventilation slots are blocked
• Disconnect main power before replacement or servicing.
• Make sure there is no ammable materials close to the unit while
operating as it is re hazard.
• Use safety cable when xing this unit. Don’t handle the unit by holding its
head only, always hold it by its base or body.
• Maximum ambient temperature is at:104°F. Don't operate where the
temperature is higher than 104°F.
• Unit surface temperature may reach up to 185°F. Dont touch the housing
bare-hand during its operation. Turn o the power and allow 15 minutes
for the unit to cool down before replacing or serving.
• In the event of serious operating problem, stop using the unit
immediately. Never try to repair the unit by yourself. Repairs carried out
by unskilled people can lead to damage or malfunction. Please contact
the nearest authorized technical assistance center. Always use the same
type of spare parts.
WARNING
• To prevent or reduce the risk of electrical shock or re, do not expose the
unit in the rain or moisture.
• Do not open the unit within ve minutes after switching o.
• The housing, the lenses, or the ultraviolet lter must be replaced if they
are visibly damaged.
www.PyleUSA.com www.PyleUSA.com
3. CAUTION
There are no user serviceable parts inside the unit. Do not open the
housing or attempt any repairs by yourself. In the unlikely event your
unit may require service, please contact your nearest dealer.
4. INSTALLATION
The unit should be mounted via its screw holes on the bracket. Always
ensure that the unit is rmly xed to avoid vibration and slipping while
operating. Make sure that the structure to which you are attaching the
unit is secured and able to support a weight of 10 times of the unit’s
weight. Always use a safety cable that can hold 12 times of the weight of
the unit when installing the xture. The equipment must be xed by
professionals. The PDJLT50 must be xed at a place where it is out of
touch of people and no one can pass by or under it.
• DISPLAY
To show the various menus and the selected functions
• LED
• Button
• MAINS INPUT
Connect to power supply.
• MAINS OUTPUT
Connect to supply power to the next unit
• DMX INPUT / OUTPUT
For DMX512 link, use 3/5-pin XLR cable to link the unit together.
Please read carefully the instruction, which includes important
information about the installation, usage and maintenance
WARNING
DMX
On
DMX input Present
MASTER
On
Master Mode
SLAVE
On
Slave Mode
SOUND
Flashing
Sound activation
MENU
To select the programming functions
DOWN
To go backward in the selected
functions
UP
To go forward in the selected
functions
ENTER
To conrm the selected functions
1 2

www.PyleUSA.com www.PyleUSA.com
8. CHANNEL MODEL FUNCTION
9 CHANNEL MODE
14 CHANNEL MODE
3 4
REST REST
Reset
MAFA
FASt
Host rapid self-propelled
MStS
Host Voice mode
SlAu
Slave Set
MASL-SLOU
Host a slow self-
propelled
PAn
PAn
X Motor Forward
TiL
TiL
Y motor is transferred
rTiL
X motor is transferred
MStc
。。
Stand-alone mode
rPAn
Y Motor Forward
diS
diS
Forward Show
rdiS
Reverse Display
14CH
14CH
14 CH mode
9CH
9 CH mode
PA54
PA54
X motor 540 degree turn
PA36
PA543
6
X motor 360 degree turn
PA18
PA543
6
X motor 180 degree turn
Ti27
Ti27
2727
Y motor 270 degree turn
Ti18
PA543
6
X motor 180 degree turn
Ti09
PA543
6
Xmotor 180 degree turn
LOAD LOAD
Initialization parameters
d001
001-512
Controller control
Channel Function
1
0-255
Level
2
0-255
Vertical
3
0-7
8-134
135-239
240-255
Dimming and stroboscopic
No eect
Dimming
Strobe from low to fast
medallion
4
0-255
Red dimming
5
0-255
Green dimming
6
0-255
Blue dimmming
7
0-255
White dimming
8
0-255
Motor speed
9
150-200
Reset
Channel Function
1
0-255
level
2
0-255
Level dimming
3
0-255
vertical
4
0-255
Vertical dimming
5
0-255
speed
6
0-7
8-134
135-239
240-255
No eect
dimming
Strobe from low to fast
medallion
7
0-255
Red dimming RED
8
0-255
Green dimming GREEN
9
0-255
Blue dimming BLUE
10
0-255
White dimming WHITE
11
0-7
8-231
232-255
Color selection
Color combination 1
Color jump
12
0-255
Color speed
13
0-142
143-255
Auto
Sound 1
14
150-
200
Reset