Pyle PSW588UT User manual

Thank you for choosing our productsThank you for choosing our products
Multifunctional double deck wall mount
Fixed Flat Panel TV Bracket
Easy installing: Just hang up the display
Safety: locking by locking bar on the bottom
Max load capacity:45kg/99lbs
TV size range: 32 ~50""
INSTALLATION GUIDE
Item No.:PSW588UTItem No.:PSW588UT
Warning: Some TV require two people to lift, as we are not responsible for any personal
injury or product damage due to mishandling.
Warning:
Fig 3c
3
4
UP
UP
5
UP
UP

Hardware List: Actual parts appearance and the quantity may different
with illustrated.
Hardware List:
1
3
22
UP
UP
Fig 3b
4
3
UP
Step 3: Hanging display
Firstly lift the bracket mounted display over the wall
mount. And then hook the brackets over the top of the
wall mount. Rotate the display let the bottom of the
brackets hook over the bottom of wall mount, as shown
in Fig.3a. Then use the Locking bar(3) to prevent the
display from being removed or accidentally knocked off
of the wall plate.When the locking bar half insertes into
the wall plate , you can use the rotating rod(4) to make
it fully inserted. (4)
Step 3: Hanging display
Fig 3a
2
1
.
.
screw out the locking rod ,then the
TV is settled, if you think
the ribbon is too long,You could hide it at the back of
thetelevesion,onceyouwanttouninstalltheTV,itcouldhelpyoutotakeoutthe
locking bar
AsshowninFig.3bandFig3c
(5)
(3)
5
5
A-H LI K
JM
ID Description
1
2
A
3
B
1
2
4
1
4
Wall plate
Bracket
Locking bar
M4 mm×12 bolt
M4 mm×16 bolt
Qty
41
Rotating rod
51
Ribbon
4
4
4
F
G
H
ISquare washer
Long bolt
Wall anchor
Long bolt washer
C4M5× mm16 bolt
M6× mm16 bolt
M8×16mm bolt
D4
4
4
E
ID Description
Qty
J
K
L
M
4
4
4
4M5×3 mm6 bolt
M6×3 mm6 bolt
M8×36mm bolt
Square

WARNING
We are not responsible for any personal injury or product damage due to mishandling,
incorrect mounting, incorrect assembly or incorrect use of this product.
The supplied wall mounting hardware is not for use on steel stud walls or cold
cinder block walls. If you are uncertain about the nature of your wall, please consult a
qualified contractor. If the hardware you required is not included please contact your
local hardware store.
Note:
Caution:This Product LCD /Plasma Wall Mount Bracket is intended for use only
with the maximum weights indicated .See apparatus instructions .Use with products
heavier than the maximum weights indicated may result in instability causing possible
injury .
Caution:
Step 1: Attach bracket to TV
CheckyourTVmanualtoconfirmthediameterofbolttobeusedorchoosean
appropriate bolt according to size, height and position of the holes on your TV. See
pages 4 of these instructions for examples.
For correct installing, make sure that hook of every bracket must facing down. Use
selected bolts and washers for installing bracket at the back of display. Adjust two
brackets to equal heights and level. Once aligned, tightly secure the bolts.
As shown in Fig.1a.
Don't force the bolt into the hole, which will cause a damage of
equipments and injure of person. Don't use electric drill to fasten any bolts.
Note:
the UP side on the top"" .
IMPORTANT:
Step 1: Attach bracket to TV
IMPORTANT
Note:
Fig.1a
UP
UP
After determining the height of stand, follow the installation instructions in below
to install wall mount to different kinds of wall -wooden, brick, concrete and stone.
Using a awl or nail to make where the nails are located, as shown as fig.2b. Pre-drill
these holes with a 5mm drill bit to at least 40mm in deep hole. Please make sure
these holes are level and located at center. Use wall mount as a template to mark the
location of other holes and drill the same holes. Fix the wall mount to the wall
with long bolts(J) and washers(L).
Wooden wall:
three
4
Wooden wall:
Fig 2b Fig 2c
Brick, Concrete and Stone wall:
Using the wall mount as template to mark 4 holes location on the wall. Two holes are
located at the top row of the slots and two more are located at the bottom row. Please
make sure these holes are level. Pre-drill these holes with a 10mm drill bit to at least
50mm deep hole. Insert wall anchors(K) into each of these holes. Attach the wall
mount to the wall using 4 long bolts(J) and washers(L). as shown as fig.2c.
Brick, Concrete and Stone wall:
L
1
J

Following examples shows how to use bolts and square washers.
Install the bracket directly to the back of display by using bolts and square washers
provided. As shown in Fig.1b.
Fig 1b
b
15 degree
viewing angle
eyelevel
a
Fig 2a
Step 2: mount to wall
First, determine the height of stand
The best height of stand is parallel to eyelevel of a person who sitting on a couch.
Normally, the horizontal distance of eyelevel is about 4’ from ground level.
The following two conditions are for determining the perfect height of stand:
1) the distance between wall and couch(Fig 2a).
2) the distance of eyelevel from ground level plus the distance measured from
eyelevel of a person sitting on couch with viewing angle of 15 (Fig 2a).
For example:
1) the distance of ‘a’ is 5’-7’, the distance of ‘b’ is about 1’
2) the distance of ‘a’ is 8’-13’, the distance of ‘b’ is about 3’
3) the distance of ‘a’ is 14’-17’, the distance of ‘b’ is about 4’
The perfect height of stand centre will be anywhere within b, where you feel
comfortable for viewing.
°
AttachStep 2: Attach mount to wall
A,B
2
C,F
2
D,G
2
E,H
I
II
I
2
M4Fig bit M5Fig bit
M6Fig bit M8Fig bit
PYLE MISCELLANEOUS PARTS MISC ACCESSORIES