Pyle Pure Clean PUCRC17 User manual

PUCRC17
Robot Sweeper
USER MANUAL

1
www.PyleUSA.com
2
www.PyleUSA.com
CAREFULLY READ THIS MANUAL BEFORE OPERATING THE MACHINE.
ANY WRONG OPERATION MAY CAUSE DAMAGE OR INJURIES.
SAFETY INSTRUCTIONS:
1. Do not use next to steps or on balconies. This machine does not have step
avoidance sensors.
2. This machine is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities. It is not also intended for
use by those with a lack of knowledge and experience, unless they have
been given instruction or supervision concerning the use of the machine by
a person responsible for their safety.
3. This appliance is for indoor use only.
4. This unit is suitable for low to medium le carpet. It is not suitable for
uneven oor or in mixed carpet.
5. Take o the side brush when cleaning undercoat carpet to protect the side
brush.
6. A damaged power supply should be replaced only with the original parts
from manufacturer.
7. Do not use on wet or greasy dust.
8. Before operation, move away the fragile things (glass, light and etc) and
other things possibly entangle brushes (long hair, plastic bag, rope, wire etc.)
9. Don't sit on the machine or put heavy things on it.
l0. Clean the machine regularly. Empty the dust container.
11. If the robot is not to be used for more than 3 months, charge the robot
sweeper for 12 hours
12. Charge only when it alarms for low power or powers o. Fully charge the
robot sweeper before use.
13. Battery can be recycled if the machine breaks.
COMPONENTS
2
3
4
5
6
7
8
9
11
12
10
113
14
15
16
17
1. Cli Detection Sensor
2. Side Brush
3. Right Wheel
4. Charger Port
5. On/O Button
6. Battery Cover
7. Middle Brush Holder
8. Left Wheel
9. Brush Wheel
10. Dustbin
11. Dustbin Release Button
12. Universal Wheel
13. Start/Pause Button
14. LED Indicator
15. Light Sensor
16. Handle
17. Obstacle Sensor
HOW TO ASSEMBLE SIDE BRUSH:
HOW TO OPERATE
1. Before activating the machine, make sure the dust bin is empty, brush
wheel and side brush are assembled properly .
2. Remove any object from the area to be cleaned in advance.
3. Turn on the power button, music will play accordingly. LED indicator is on,
the machine will enter stand by status.
4. Press Start/Pause button, machine will start working.
5. When in operation, press start/pause button and the machine will stop
temporarily
6. When machine stops unexpectedly, LED indicator will blink in 3Hz, please
check carefully if machine being entangled or brush wheel fails to operate,
if machine is being entangled, place it to a spacious place to re-start, if
brush wheel fails to operate, take it out and clean. If the machine still won’t
start properly and malfunction happens, long press ON/OFF button to
power o the machine, and start again. If the malfunction still exists, send
the machine to a service center for repairing.
7. When machine stops working, LED indicator will slow ashes lHz, which
means low battery, please charge it in time. The LED indicator ashes when
charging and will constantly on after fully charged, plug out the charger
when fully charged.
Hexagonal Hole
face down
There is a hexagonal hole at the bottom of side brush, align the brush
and press it until clicks in.

3
www.PyleUSA.com
4
www.PyleUSA.com
HOW TO REMOVE AND REINSTALL THE MIDDLE BRUSH:
HOW TO CHARGE BATTERY
Note: If the machine shuts down when working, the display shows "!" and the
battery light ashes, that means power shortage and the machine needs to be
recharged.
1. Plug the adapter into the power outlet.
2. Plug the lead in the charging port next to the ON/OFF button.
3. With a sound, three grids electricity dynamically ashing. The screen shows
the charging status. It means the machine is charged normally.
4. When fully charged, it will beep again. The display shows 99% and three
grids electricity fully lit up. Then remove the charger.
5. Plug out the charger and power cord
HOW TO REPLACE BATTERY
CLEANING AND MAINTENANCE
• Make sure the unit is unplugged before cleaning.
• Do not clean the machine and power supply by immersing in water or other
liquids.
1. Metal parts (power plug or terminal): Wipe them with a clean dry cloth.
2. Plastic parts: Wipe them gently by a clean, soft cloth together with water or
mild detergent.
3. Do not use gasoline, alcohol, rubber water and other strong irritant
cleaning lotion to clean it.
4. Store the robot in a cool and dry place.
PRODUCT SPECIFICATIONS
Turn the robot upside down on a at
surface, press the middle brush release
catch, take out the brush and wheel.
Clean the brush and the side wheel and
reverse procedure to reinstall.
1. Open the battery cover and take
out the battery and save the
screws.
screw on
battery cover
2. Remove the connector.
Press the lock on the connector
and pull o.
Buckle
3. Replace with new battery.
Push down the lock and push the
right part to the left unit until you hear
it clicks into place.
4. Close the battery cover and
secure it with the screws you
saved.
Power supply
Rechargeable battery
Voltage
Input:l00-240VAC 50-60Hz 0utput:9VDC,500mA
Battery
N I MH 7.2V 2l00mAh
Charging time
4.5hrs
Continuously working time
Around l20minutes
Capacity of dustbin
0 . 3L
Clean eciency
over 98%
Clean width
2 4 0 mm
Product size
Diameter:286mm Width:65mm
Net weight
About l.70kg

5
www.PyleUSA.com
6
www.PyleUSA.com
TROUBLESHOOTING
Please read this instruction manual carefully before sending to after-sale
service center. Following are troubles and solutions for your reference.
TROUBLE POSSIBLE REASON SOLUTION
Abnormal sound
Works only for a
short time even
battery is fully
charged
Machine stops when
in operation, LED
indicator ashes
quickly
LED indicator ashes
slowly
Without obstacle
ahead, machine often
makes wrong turn
Machine often back
and forth in the same
spot
Machine falls from
height or upstairs
Robot often stops
under the bed
Serious deform of
side brush
Side brush does not
work in operation
Dustbin won’t close
The robot is entangled
or trapped
The brush wheel can
not operate or battery
defected
1. Machine is trapped.
2. Brush wheel or side
brush is entangled.
3. Machine malfunction
Low battery
1. Dust in the universal
wheel
2. Dirt in anti-falling
sensor
There’s some objects
under the machine
Malfunction on
anti-falling sensor
1. Lack of light under bed
2. Dirt on light sensor
Normal damages
Side brush is entangled
by hair
Button can not pop out
after pressing in
Clear the debris surrounding
the brush wheel
Remove the brush wheel and
clear it. If still does not work,
consult distributor to replace
new battery
1. Put the machine to a
spacious place to restart
2. Clean the brush wheel or
side brush
3. Restart the machine, send it
to after-sale service center if
problem still exists.
Recharge the machine
1. Remove universal wheel,
open the cover board, clean
the dust.
2. Clean the anti-falling sensor
Check if it s an even oor or
if theres any object under
the machine
Clean the anti-falling sensor
by soft cloth or tissue. send it
to after-sale service center if
theres still problem.
1. Working room is dark, open
window or turn on the light
2. Clean the light sensor
Replace new side brush
Take o the brush and
remove the hairs
Remove the screws in the
dustin cover, take o the
button cover, clean and
reinstall.