Qazqa 90500 User manual

VAP Duo WL Black Solar
MODEL: 90500
Important: Please ensure that you charge the solar lights in maxi-
mum sunlight for a period of up to 3 days (for 2200mAh Ni-MH)
before switching on the lights, in order that the lights work on a full
charge
HOW TO DETERMINE WHERE TO MOUNT YOUR SOLAR
PIR SENSOR LIGHT
The most important thing to remember for the operaon of your
SOLAR PIR SENSOR LIGHT is that it works from the power contained
in DIRECT SUNLIGHT. The more direct sunlight the solar cell receives
in a day, the longer the light will operate.
11
3 days/72h
12
5sec1min
5
9
02 4 6 8mm
H:2.5m
φ6mm
30mm
3
10
130°
6x
6x
4x30mm
6x27mm
90°
45° 45°
90°
90°
45°
45°
130° 130°
39.5mm
46
88mm
40mm
76mm
7
φ6mm
30mm
8
90°90°
180 mm
157 mm
142 mm
207 mm
166 mm
110 mm

Main Unit:
The main unit contains the 2*6*0.5W LED, moon sensor and baery
(Ni-MH Rechargeable baery, 3.6V 2200mAh). When deciding where
to mount this unit, keep in mind that the moon sensor that acves
the light has a “field of vision” of min. 8 meters (in front of the light)
and about 130º (horizontal) at 25℃ environmental temperature.
Solar Cell:
The solar cell is the power source for the SOLAR PIR SENSOR LIGHT. It
converts the sun’s energy into electricity that charges the baery
stored in main unit. This requires DIRECT SUNLIGHT falling onto the
face of solar cell for as long as possible over the course of day.
Use the three screws supplied (#4 on parts list) to mount the solar
cell unit onto a solid surface. Make sure it is anchored into the solid
surface.
You can adjust the angle of the solar cell by moving the adjustment
support to the appropriate hook on the mounng bracket. Remem-
ber, it must face as much DIRECT SUNLIGHT over the course of the
day as possible. Keep in mine shadows that may block sunlight at
some point during the day.
Now carefully route the solar cell power cord to the main unit and
plug it into the connector on the side of the unit.
FINAL ADJUSTMENT AND START-UP
Aer you successfully installed your SOLAR PIR SENSOR LIGHT, you
are almost ready for carefree operaon with a few final steps:
Inial 3-days Charge:
On the main unit there is a dial switch with 2 posions:
●OFF ● AUTO
AUTO —
Posion for normal operaon of unit.
OFF ---
1) Posion for shipping or extended periods of non-use
2) Posion for inial 3-day charge before final adjustment and first
use. (Although the unit can charge, it is not operaonal in this
mode)
For now, turn the dial switch to OFF posion. In this posion the solar
cell will charge the baery without acvang the unit. Leave the
switch in this posion for 3 sunny days to ensure that the baery has
a full charge prior to moon sensor adjustment and normal opera-
on.
OFF AUTO
2

HOW TO ADJUST THE MOTION SENSOR
Aer the inial 3-day charge, slide the switch on the main unit to
AUTO posion.
On the moon sensor there are threes adjusng knobs: TIME / LUX
1) TIME --- Duraon me: Depending on how long you wish the unit
to stay lit aer moon stops in the field of vision, the duraon
me will adjust from 10 seconds to 1 minute. Note: Once the light
has been triggered by the PIR sensor any subsequent detecon
will start the med period again from the beginning..
2) LUX – Lux control level: The Lux control module has a built-in sen-
sing device (photocell) that detects daylight and darkness.( )
posion denotes that the loading will be turned on by PIR during
day and night, ( ) posion denotes that the loading will be
turned on by PIR only at night. You can set to operate the unit at
the desired level by adjusng the LUX knob.
Note: If, in daily posion, the unit turns on when it is too light out-
side, turn the control towards ( ). however, if the light is not acva-
ng during nighme because of a street light or bright house light,
turn this control towards ( ).
Walking-test:
Point the moon sensor to face the area you want to detect moon
in and set the TIME knob to minimum (-) posion and LUX knob to
“light” ( ) posion. Walking slowly within its detecon area, the
sensor can detects moving invisible infra-red radiaon given off by a
human body and then turn on the light. Test the coverage of the area
by walking slowly around unl not to switch on the light.
ADJUSTMENT OF THE LAMP HOUSING:
Point the lamp housing to face the area you wish to illuminate.
GENERAL ELECTRICAL AND SAFETY WARNINGS
1) The AUTO/OFF switch on the main unit must be in the OFF posi-
on when changing baery.
2) Do not cut the solar cell wire. Disconnue use if the wire becomes
frayed or broken.
3) Do not immerse components in liquid.
4) Do not use any other charge than the single solar charging panel
provided with the SOLAR PIR SENSOR LIGHT. This may result in
injury or damage to the light and voids any warranty.
5) Posion so that the cord is securely fastened and will not result in
a hazard (such as tripping).
3

6) When changing baery, be careful of any sharp edges that could
cut you or the wires. Do not pull on wires.
CLEANING
It is important that the solar panel is kept free of dirt and debris. A
dirty solar panel will not allow the baery to fully charge and this will
shorten the life of baery and cause the light to malfuncon.
STORAGE
If you wish to store your light indoors for more than two or three
days, follow these steps to prevent damage to baery:
1. Turn the switch to OFF posion
2. Store the light and solar panel where it can receive some sunlight
or room light each day. The baery needs light to maintain a
charge during storage.
NOTE THE FOLLOWING TROUBLE-SHOOTING:
1. Symptom: Light doesn’t acvate in normal operaon.
Correcon: make sure that:
1) The main unit switch is at the AUTO posion.
2) The Lux control is not set too far toward ( )
3) The moon sensor is posioned to face oncoming movement
4) The solar cell is angled so that it gets plenty of direct sunlight for
most of day, if not the enre day.
5) Baery charge is not too low (charge for 3 sunny days—switch
turned to OFF)
2. Symptom: Light turns on during the day.
Correcon: Make sure that
1) The Lux control is not set too far toward ( )
3. Symptom: Light quickly flashes on and off
Correcon:
1) Move the Lux control toward ( )
2) Low baery (charge for 3 sunny days—switch turned to OFF).
4. Symptom: Light is not as bright as normal.
Correcon:
1) Low baery (charge for 3 sunny days—switch turned to OFF).
4