QCAMZ FULL HD User manual
// English
QCAMZ FULL HD 1080p
170° Fisheye Waterproof // Action Cam
Introduction
Thank you for purchasing the QCAMZ FULL HD! Record your limits with this waterproof full HD
action cam!
It is highly recommended for you to read this user manual carefully in order to fully understand how
to operate the QCAMZ FULL HD correctly.
Table of Contents
What’s in the box?
How to use
Camcorder Overview
Initial set up
Charging the battery
Power ON/OFF
Taking a video
Taking snapshot photos
Memory capacity chart
Digital Video Motion Stabilisation Technology
Playback on your computer
On a Mac
Date & time setting
Webcam setting
Firmware Installation
LED status table
Removing/Installing battery
Repairs
Technical specications
Warranty
Warning
What’s in the box? 1. QCAMZ FULL HD with Sound Cap
2. Camcorder Mount
3. Universal Mount
4. Roll Bar Mount
5. Pad Mount
6. Rotating Kitset
7. Magic Tape 2pcs
8. Adhesive Stickers 8 pcs
9. Waterproof Cap
10. Rubber O-Rings 6 pcs
11. Silicon Grease
12. Hand Safety Strap
13. Rechargeable Lithium-Polymer Batteries 2 pcs
14. USB Cable
15. User Manual
How to use the QCAMZ FULL HD
1. Camcorder on Handlebar 2. Camcorder on Vented Helmets
Roll Bar Mount Camcorder Mount Magic Tape 2pcs Universal Mount Camcorder Mount
3. Camcorder for Non-vented Helmets 4. Camcorder on top of Helmet
Adhesive Sticker Universal Mount Camcorder Mount Adhesive Stickers Pad Mount Rotating Kitset Camcorder Mount
6. Camcorder on Surfboard or any curved surface
5. Camcorder on Front Helmet
Adhesive Stickers 4pcs Pad Mount Rotating Kitset Camcorder Mount Adhesive Stickers 4pcs Pad Mount Rotating Kitset Camcorder Mount
Using QCAMZ FULL HD for water sports
When using the waterproof cap remember to put some silicon
grease to the rubber O-ring from time to time, especially before
using the camera in water. Make sure to close the rear cap ③
tightly. Only use the camera in water with the waterproof cap!
Rubber O-Rings Silicon Grease Waterproof Cap
4. Mode switch
5. USB Port
6. Micro SD card slot
7. Battery
8. Microphone
9. 1080P / 720P mode switch
10. Stabiliser / rmware switch
CAMCORDER OVERVIEW
1. LED
2. Power / Shutter
3. Rear cap
Initial set up
1. Make sure the camera is OFF before inserting in or removing the Micro SD card!
2. Unscrew the rear cap from the back of the camera ③.
3. Put your Micro SD card (max up to 32GB) into the slot with the card label facing
down (contacts up). Use your ngernail to do this. You will hear a click sound once
the Micro SD card is in place. Then screw the rear cap back on tightly.
Only use Micro SD cards Class 6 or above.
4. If no Micro SD card is inserted into the camera, the LED light on top of the ca-
mera will start ashing red and blue for approx. 30 secs and then auto shut-off.
5. The Micro SD card must be blank; meaning without images from other sources
on it. If you are using a Micro SD card previously used with other cameras, please
make sure you format the Micro SD card in your computer before using it with
your QCAMZ FULL HD. New cards can be used straight from the packaging.
Charging the battery
Unscrew the cap located at the back of the camera ③ and connect the camera
with the USB cable to your PC ⑤ or charger (optional). The LED light will glow
green while charging and goes off once the battery is fully charged.
Before the rst use charge the battery for 10 hours! You can record
approx. up to 90 minutes with one charge.
Power on/off
Turn on the camera // Press and hold the POWER/Shutter button for approx. 3
seconds until the blue LED turns on and the red LED ashes once. The camera
will beep and vibrate once long, indicating it is now in stand-by mode.
Turn off the camera // Press the POWER/Shutter button again for approx.
3 seconds. The LED light will go off and the camera will short vibrate twice,
indicating it switches off.
Standby mode // If the camera is in standby mode without activity, it will auto
switch off after approx. 3 mins to conserve battery power.
Taking a video
To take a video the camera must be set to video mode. To check unscrew the cap
located at the back of the camera ③. The video/photo switch ④ must be set to the
right for the video recording standby mode, screw the cap back on tightly.
Press the Power/shutter button ② to turn on the camera. Press the Power/shutter
button again once shortly to start video recording. The camera will beep and
vibrate one short time and the LED will ash red while the video is recording.
Press the Power/shutter button again to stop recording. The camera will beep
once and vibrate two short times and the red LED will stop ashing.
Take Snapshot Photos
Unscrew the cap from the back ③, set the video/photo switch ④ to left for the
photo standby mode and screw the cap back on tightly. Press the Power/shutter
button to turn on the camera. Press the Power/shutter button ② to start taking
photos.
The camera will beep and vibrate one short time and the LED will ash red. The
camera automatically takes a photo every 3 seconds until the battery is empty or
the Micro SD card full. Press the Power/shutter button again to stop the recording.
The camera will beep once and vibrate two short times and the red LED light will
stop ashing.
Memory capacity chart
Below chart will show you the possible number of photos and videos according to
memory card size. Please use only Micro SD Cards Class 6 or above!
Memory capacity chart
Mode 4GB 8GB 16GB 32GB
HD Video Recording 720P 55 min 115 min 230 min 450 min
Full HD Video Recording 1080P 45 min 90 min 180 min 350 min
Digital Photos 450 850 1700 3500
Digital Video Motion Stabilisation Technology
The QCAMZ FULL HD comes with integrated Digital Video Motion Stabilisation
Technology reducing and compensating for unwanted video vibrations caused by
hand jiggle or rough recording conditions. It can be turned off by moving the Mode
switch ⑩ right to position F.
Playback on your computer
Turn off the QCAMZ FULL HD! Unscrew the cap at the back ③, plug the USB
cable into the USB Port ⑤ of the camera and connect it to your computer. Turn on
the camera! The camera will automatically be recognized as USB device. You can
now download the les directly from the Micro SD card inside your camera.
Alternatively you can take out the Micro SD card while the camera is turned off (!),
put it into a card reader and connect it to your PC
The camera must be turned on after it has been connected to the PC in
order to download the les. Do not remove the battery!
Trying to watch a video at the same time can lead to disruptions and
unknown outcome!
On a MAC
Using the provided USB cable, connect the camera to your Mac. Turn on the ca-
mera and the MAC OS will recognize it as an external hard drive.
IMPORTANT TIP FOR MAC USERS:
When deleting les from your Micro SD cards you must empty the rubbish bin of
your computer before removing it or unplugging the camera. If you do not follow
these instructions, photos and videos will not be completely erased from your
card.
Date & time setting
Download the time.txt le from
www.qcamz.us\Downloads\QCAMZ FULL HD
Date & Time Quick Setup for QCAMZ FULL HD:
Open the le “time.txt” and change the date & time as follows:
YYYY.MM.DD hh:mm:ss
Y = year h = hour
M= month m = minutes
D= date s = second
1. Unscrew the cap from the back of the camera ③, remove the Micro SD from the
camera and put it into your PC card slot.
2. Copy the “time.txt” le to your Micro SD. Then put the card back into your
camera and screw the rear cap back on tightly.
3. Press the Power button and now date and time has been updated
automatically!
*Once you format your Micro SD card the time and date settings will be lost!*
Webcam Setting
Pls go to www.qcamz.us\Downloads\QCAMZ FULL HD if you like to use the
QCAMZ FULL HD as a webcam.
6. The LED light will ash red for 20 seconds, indicating the camera is installing the
rmware. Afterwards it will shut itself off.
7. Now take out the Micro SD card and format it.
LED status table
Green LED Red LED Blue LED
Standby Off Off On
Battery charging On Off Off
Taking a video Off Flashing On
Taking a photo Off Flashing On
No Micro Sd card Off Asynchronous ashing
Micro SD card full Off On On
Data transfer Off Off On
Firmware Installation
It is not necessary to install any rmware to view videos or pictures. It only needs
to be installed to change the default settings from 5 minutes to 15 minutes per
video le selection, available for Windows OS systems or in case of a software
problem with the camera or available rmware update.
1. Unscrew the cap from the back of the camera ③, remove the Micro SD from the
camera and put it into your PC card slot.
2. Download the latest rmware at www.qcamz.us\Downloads\QCAMZ FULL HD
– Firmware for QCAMZ FULL HD – to your Micro SD card.
3. Put the Micro SD card back into the camera
4. Switch ⑩ to rmware mode. F = Firmware
5. Press and hold the POWER/Shutter button for about 3 seconds to turn on the
camera.
Removing/Installing battery
The battery is designed to have a tight t to maximize reliability in highly active
situations. To remove the battery, pull it out of the battery holder.
It is intentionally not easy to do, but the battery will come out.
Additional batteries and mount packages are available at www.qcamz.us
Repairs
Most helmet cameras are used for recording extreme sports and outdoor activi-
ties. This increases the danger of damaging the camera. The warranty does not
cover any damage that has occurred during sporting activities.
Before giving up on your QCAMZ FULL HD, contact us to see if we can help.
Photo: • 20.0 Mega Pixel (5296x3968)
• HD Image Sensor CMOS 9Mega Pixel 1/ 2.3”
• Format: JPEG
• Capture mode: Auto snapshot every 3 seconds
Memory: • Micro SD card, up to 32GB capacity
(Minimum Class 6 or above)
• Avg. recording time: 10-15min/GB
Product size: 104 x 32 mm // Weight: 105g (without battery)
Operating Systems (for USB Drive): Win ME, 2000, XP, Vista; Win7; Mac OS X 10.6+
Charger (optional): Input: AC 110 ~ 240V 50/60Hz
Output: DC 5.0 - 5.5V ....450 - 550mA
Technical Specications
Optics: • 170° FISHEYE view @ 1080p Mode
Super Wide Angle view @720p Mode
• f/2.4, xed focus glass lens
Video: • Full HD Resolution: 1920x 1080 @30fps
• HD Resolution: 1280x 720 @ 60fps
• Digital Video Motion Stabilization Technology
• Light Sensitivity: 960mV / (Lux-sec)
• Video Format: H.264 (avc1) / MOV
• Exposure control: Auto
• White Balance: Auto
Audio: • Built-in microphone
Warranty:
This product is covered by a Limited Warranty on parts and labour from the date
of original purchase. The warranty period depends on the legislation of the country
you reside in. The warranty covers defects in workmanship and materials.
The warranty does not apply to units which have been damaged or abused inten-
tionally or unintentionally. The warranty does not apply to units where the rear caps
were incorrectly used or closed, to cosmetic damage, to units that have been
modied or have modied parts on them.
Tampering with or altering the unit will void the warranty. Any unauthorized service
will void the warranty. Purchase from individuals or unauthorised internet websites
voids the warranty. The original sales receipt must be produced for any warranty
service. The warranty does not cover any damage that may occur during sports
activity. It is the user’s responsibility to securely attach the QCAMZ FULL HD to
any sports equipment.
WARNING:
The form and functions of QCAMZ FULL HD, accessories, logos, and all graphics
are the patented, protected property of Alvission Group Ltd.
Any attempt by anyone other than our authorised dealers to copy or reproduce
any of the above without permission of Alvission Group Ltd. or its appointed local
dealers will be met with legal action. Alvission products are available for purchase
only from authorised dealers.
Thank you very much for purchasing QCAMZ FULL HD and we are sure
you will enjoy this product!!
This manual is subject to technical changes without prior notice.
www.qcamz.us
Table of contents
Other QCAMZ Action Camera manuals
