QFX CR-30 User manual

CLOCK RADIO
Model no.: CR-30
PLEASE READ THIS USER MANUAL COMPLETELY BEFORE
OPERATING THIS UNIT AND RETAIN THIS BOOKLET FOR
FUTURE REFERENCE.

WARNINGS
•To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
• To reduce the risk of electric shock, do not open the cabinet. No user serviceable parts are
inside. Refer servicing to qualified personnel.
• This appliance uses a Laser System. To prevent direct exposure to the laser beam do not
open the cabinet.Visible and invisible laser radiation is present when the cabinet is open.
Avoid direct exposure and do not stare into the beam.
• Batteries should not be exposed to excessive heat such as direct sunlight, fire, or other
heat sources.
• Caution: Do not expose this appliance to dripping or splashing liquids. Do not put objects
filled with liquid, such as vases on or near the appliance.
• Caution: To turn this appliance off completely, the POWER cord must be unplugged from
the wall outlet. The power cord must be easily accessible at all times.
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade and/or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.

10) Protect the POWER cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged inany way, such as POWER-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.

LOCATION OF CONTROLS
1. FUNCTION button 7. NEXT / MINUTE button
2. CLOCK / MEMORY button 8. SNOOZE button
3. VOLUME DOWN / ALARM-1 button 9. LED Display
4. SLEEP button 10. Battery Door
5. VOLUME UP / ALARM-2 button 11. AC Power Cord
6. PREV / HOUR button •AC 120V~60Hz 3W
NOTE: Some buttons have multiple functions based on if the function requires a
“Press” (Press & Immediately Release the button) command or a “Press & Hold”
(Press & Hold the button for 1-2 seconds) command.

EXPLANATION OF DISPLAY LIGHTS
LETTER DESCRIPTION
A “PM” INDICATOR LIGHT
B ALARM-1 BUZZER INDICATOR LIGHT
C ALARM-1 RADIO INDICATOR LIGHT
D ALARM-2 BUZZER INDICATOR LIGHT
E ALARM-2 RADIO INDICATOR LIGHT
SETTING THE TIME
NOTE: Before setting the TIME make sure all of the non-clock functions (BLUETOOTH,
FM,
AM) are turned OFF. If any of the non-clock functions are playing, turn the function OFF by
simply pressing & holding the FUNCTION button (1).
1. Press & hold the CLOCK / MEMORY button (2) until the time flashes on the LED
display. Once the time is flashing you can release the CLOCK / MEMORY button (2).
2. Press the PREV / HOUR button (6) repeatedly until the correct HOUR is shown on
the LED display.
• NOTE: The “PM” Indicator Light (A) will turn ON when the hour is set to PM.
For AM hours the “PM” Indicator Light (A) will turn OFF.
3. Press the NEXT / MINUTE button (7) repeatedly until the correct MINUTE is shown
on the LED display.
SETTING THE ALARM
CAUTION: Before setting theAlarm make sure the correct TIME is shown on the LED
Display.
NOTE: Before setting the TIME make sure all of the non-clock functions (BLUETOOTH,
FM,AM) are turned OFF. If any of the non-clock functions are playing, turn the function
OFF by simply pressing & holding the FUNCTIONbutton (1).

1. Press & hold the VOLUME DOWN / ALARM-1 button (3) until the time flashes on the
LED display and the ALARM-1 BUZZER Indicator Light (B) flashes. Once the time is
flashing you can release the VOLUME DOWN / ALARM-1 button (3).
2. Press the PREV / HOUR button (6) repeatedly until the correct HOUR is shown on the
LED display.
• NOTE: The “PM” Indicator Light (A) will turn ON when the hour is set to PM.
For AM hours the “PM” Indicator Light (A) will turn OFF.
3. Press the NEXT / MINUTE button (7) repeatedly until the correct MINUTE is shown on
the LED display.
4. After setting the HOURS & MINUTES press the VOLUME DOWN / ALARM-1
button (3) to confirm the ALARM-1 time.
5. The clock will automatically set the Alarm-1 for BUZZER and the ALARM-1 BUZZER
Indicator Light (B) will turn ON.
6. To choose to wake to RADIO simply press the VOLUME DOWN / ALARM-1 button
(3) until the ALARM-1 RADIO Indicator Light (C) turns ON.
7. To turn the ALARM OFF press the VOLUME DOWN / ALARM-1 button (3) until
both the ALARM-1 Indicator Lights (B & C) turn OFF.
SETTING THE SECOND ALARM
NOTE: This Alarm Clock can be set for two separateAlarm times.
NOTE: Before setting the TIME make sure all of the non-clock functions (BLUETOOTH,
FM,AM) are turned OFF. If any of the non-clock functions are playing, turn the function
OFF by simply pressing & holding the FUNCTION button (1).
1. Press & hold the VOLUME UP / ALARM-2 button (5) until the time flashes on the LED
display and the ALARM-2 BUZZER Indicator Light (E) flashes. Once the time is flashing
you can release the VOLUME UP / ALARM-2 button (5).
2. Press the PREV / HOUR button (6) repeatedly until the correct HOUR is shown on the LED
display.
• NOTE: The “PM” Indicator Light (A) will turn ON when the hour is set to PM.
ForAM hours the “PM” Indicator Light (A) will turn OFF.
3. Press the NEXT / MINUTE button (7) repeatedly until the correct MINUTE is shown on
the LED display.
4. After setting the HOURS & MINUTES press the VOLUME UP / ALARM-2 button (5)
to confirm the ALARM-2 time.
5. The clock will automatically set the Alarm-2 for BUZZER and the ALARM-2 BUZZER
Indicator Light (E) will turn ON.
6. To choose to wake to RADIO simply press the VOLUME UP / ALARM-2 button (5)
until the ALARM-2 RADIO Indicator Light (F) turns ON.

7. To turn the ALARM OFF press the VOLUME UP / ALARM-2 button (5) until both the
ALARM-1 Indicator Lights (E & F) turn OFF.
SNOOZE
Once the alarm sounds you can press the SNOOZE button (4) and the alarm will temporarily
be silenced.After Nine Minutes have passed the Alarm will sound again.
STOPPING THE ALARM
To permanently stop the alarm from sounding simply press the FUNCTION button (1) and
the alarm will automatically stop.
• NOTE: The Alarm-1 and/or Alarm-2 setting will still be ON and set for the same
time for the next day.
FUNCTION
The FUNCTION button (1) will turn the non-clock functions ON & cycle through the
different function options ( FM, AM).
• To turn the non-clock functions ON, simply press the FUNCTION button (1)
repeatedly until you arrive at the desired function (FM, AM)
• To turn the non-clock functions OFF, press & hold the FUNCTION button (1) until the
LED display shows only the current time.
VOLUME
• To Increase Volume - Press the VOLUME UP / ALARM-2 button (5)
• To Decrease Volume - Press the VOLUME DOWN / ALARM-1 button (3)
LISTENING TO RADIO
1. Press the FUNCTION button (1) repeatedly until the LED Display shows a FM Radio
frequency (such as “87.5” or “108”).
2. To listen to AM Radio simply press the FUNCTION button (1) until the LED Display
shows an AM Radio frequency (such as “520” or “1710”).
3. To change to a different Radio Station (Frequency) press the NEXT / MINUTE button (7)
to tune to a higher numbered station, or press the PREV / HOUR button (6) to tune to a
lower numbered station.
4. Press and hold the NEXT / MINUTE button (7) to begin the sequential sweep of allfrequency
channels starting form the lowest frequency to the highest frequency.

Press the NEXT / MINUTE button (7) again to stop the SWEEP. You can also press the
NEXT / MINUTE button (7) quickly to select an individual frequency.
5. Press and hold PREV / HOUR button (6) to begin the sequential sweep of all frequency channels
starting form the highest frequency to the lowest frequency.
Press the PREV / HOUR button (6) again to stop the SWEEP. You can also press the PREV / HOUR
button (6) quickly to select an individual frequency.
• TIPS FOR BEST RECEPTION
The AM & FM antennas are built-in to the cabinet of this player. To improve
reception of radio stations simply move the entire player to another location
until reception improves.
RADIO PRESETS
This Alarm Clock can store 10-FM & 10-AM radio stations in the Preset memory. To store
preset stations follow the steps below.
1. Use the NEXT / MINUTE (7) or PREV / HOUR (6) buttons to tune to the desired radio
station.
2. Press & hold the CLOCK / MEMORY button (2) until “P01” flashes on the LED
Display.
3. Use the NEXT / MINUTE (7) or PREV / HOUR (6) buttons to choose which preset
(P01 – P10) you wish to use for the current Radio Station.
4. Press the CLOCK / MEMORY button (2) to set the current Radio Station to the selected
preset shown on the LED Display.
5. Repeat steps 1-4 to set additional presets into the memory.
To tune directly to your Radio Presets simply press the CLOCK / MEMORY button (2)
repeatedly to cycle through the Presets stored in the memory.
SLEEP FUNCTION
This Alarm Clock can be set to play music for a set amount of time (10-60 minutes) and then
automatically turn OFF using the SLEEPTimer.
To turn the SLEEPTimer function ON simply press the SLEEP button (4) and “90” will
show
on the LED Display indicating the music will automatically turn OFF after 90 minutes.
To adjust the amount of time before the music will turn OFF, press the SLEEP button (4)
repeatedly until the correct amount of time (90 – 80 -70 – 60 – 50 – 40 – 30 – 20 – 10
minutes) is shown on the LED Display.
To turn the SLEEPTimer OFF continue pressing the SLEEP button (4) until the LED Display
shows “OFF”.

BATTERY INSTALLATION FOR POWER BACKUP - Requires 2
AAABatteries (Not Included)
In case of a Power failure, the Battery Backup will keep the Clock &Alarm times accurate
until the main power has been restored.
During a power failure the LED display will remain OFF until power has been restored.
NOTE: Batteries are not required for normal use of this clock. The purpose of the Battery
Backup is to insure the correct Time & Alarm settings are stored in the Clock Memory in the
event of a power failure.
• Open the Battery Compartment by gently pushing the tab on the compartment door in
the direction indicated on the bottom of the clock.
• Insert 2 AAA batteries (not included) following the + / - polarity as indicated in the
compartment.
• Replace the door to the Battery Compartment and make sure it properly clicks in
place.
NOTE: Do not force the door as breakage may occur.
TROUBLESHOOTING
Symptom Possible Cause Solution
Alarm did not sound - Alarm was not properly
turned ON.
- Alarm was not set to the
correct
Time (AM / PM)
- Check the LED Display
Lights
to insure the correctAlarm is
turned ON
- Check the Alarm Time reset
as necessary
No sound - Clock not in correct
Function.
- Volume set at minimum
- Press the FUNCTION
button
(1) to the desired Function
( FM, AM).
- Increase Volume.
Time is Flashing - Power Loss - Reset the Time

RADIO RELOJ
Modelo no.: CR-30
Por favor lea este manual completamente antes de utilizar este
equipo, y consérvelo para futuras referencias.