Qixiang Technology QX310 User manual

Website: www.keennew.com
Qixiang Technology, Contact Us for purchasing Email: [e-mail]
Whatsapp: [phone]
1
Installation and Configuration Quick Guide
QX310
Industrial Cellular Router Din Rail Mount
(2 Eth + 1 SIM + 1 RS232/RS485)
Package Contents
Before installing QX310 Router, please verify the kit contents as
following.
1 x QX310 Industrial Cellular Router Remote Gateway
1 x power adapter(12V DC/1A, EU/US/UK/AU plug optional)
1 x Quick Start Guide
1 x Ethernet Cable
1 x SMA Cellular antenna (default: magnet/optional: stubby)
1 x SMA Wi-Fi antenna (default: magnet/optional: stubby)
1 x 35mm DIN rail mounting kit
1 x RS232/485 serial cable
*If any of the above items is missing or damaged, please contact your sales representative.
Environmental Requirements
Input voltage: 7.5V-32V(standard DC12V/1A)
Operating temperature: -30 to +70 °C
Storage temperature: -40 to 85°C
Relative humidity: < 95% (no condensation)

Website: www.keennew.com
Qixiang Technology, Contact Us for purchasing Email: [e-mail]
Whatsapp: [phone]
2
Hardware Introduction
1. Overview
2. 7 Pin terminal block
1
DI
Redundant Interface
2
DO
Redundant Interface
3
RX/A
Data Input
4
TX/B
Data Output
5
GND
GND
6
V-
Power Input (Negative)
7
V+
Power Input (Positive)
3. LED Indicators
Name
Color
Status
Description
PWR
Green
On
Router is powered on
Off
Router is powered off
WiFi
Green
On
WiFi is on
Off
WiFi is off
SYS
Green
On
Redundant
Off
Redundant
WAN
Green
On, blinking
Link connection is working
Off
Link connection is not working
LAN
Green
On, blinking
Link connection is working
Off
Link connection is not working
NET
Green
On, solid
Network is joined successfully
and worked in an optimum one
Off
Network is not joined
4. Reset Button
After powered on the router, press and hold the RST button for 10 seconds,
and release the button to return the router to factory defaults.

Website: www.keennew.com
Qixiang Technology, Contact Us for purchasing Email: [e-mail]
Whatsapp: [phone]
3
Hardware Installation
1. Insert or Remove SIM Card
Insert or remove the SIM card as shown in the following steps.
Insert SIM card
1) Make sure router is powered off.
2) To open the SIM card slot, use a card removal pin plug in the card hole.
3) To insert SIM card, press the card with finger until your hear a click and
then push back the sim card slot
Remove SIM card
1) Make sure router is powered off.
2) To open the SIM card slot, use a card removal pin plug in the card hole.
3) To remove SIM card, press the card with finger until it pops out and then
take out the card.
4) To push back the sim card slot.
Note:
1) Use the specific card when the device is working in extreme temperature
(temperature exceeding 40 °C), because the regular card for long-time
working in harsh environment will be disconnected frequently.
2) Do not forget to push back the card to avoid being lost.
3) Do not touch the metal of the card surface in case information in the
card will lose or be destroyed.
4) Do not bend or scratch the card.
5) Keep the card away from electricity and magnetism.
6) Make sure router is powered off before inserting or removing the card.
2. Attach External Antenna (SMA Type)
Attach external SMA antenna to the router’s antenna connector and twist
tightly. Make sure the antenna is within the correct frequency range
provided by the ISP and with 50 Ohm impedance.
3. Mount the Router

Website: www.keennew.com
Qixiang Technology, Contact Us for purchasing Email: [e-mail]
Whatsapp: [phone]
4
The router can be placed on a desktop or mounted to a DIN rail.
DIN rail mounting
Use 3 pieces of screws to fix the DIN rail to the router, and then hand the
DIN rail on the mounting bracket. It is necessary to choose a standard
bracket mount the router with the wall mounting kit on the wall.
4. Connect the Router to a Computer
Connect an Ethernet cable to the LAN port of the router, and connect the
other end of the cable to your computer.
5. Power Supply
The power interface is in the 7 Pin terminal block on the top panel. Connect
the power adapter with the convert cable with Pin terminal block.
Note: The range of power voltage is 7.5V-32V DC
PC Configuration
There are two methods to get IP address for the PC. One is to obtain an IP address automatically from “Local Area Connection”, and another is to configure
a static IP address manually within the same subnet of the router. Please refer to the steps below.
Here take Windows 10 as example, and the configuration for windows system is similar.

Website: www.keennew.com
Qixiang Technology, Contact Us for purchasing Email: [e-mail]
Whatsapp: [phone]
5
1. Click Start >Control panel, click Network and Internet, click Network
and Sharing Center, click Change Adapter Settings, and then double-click
Local Area Connection (Ethernet).
2. Click Properties in the window of Local Area Connection (Ethernet)
Status.
3. Choose Internet Protocol Version 4 (TCP/IPv4) and click Properties.
4. Two ways for configuring the IP address of PC.
1) Obtain an IP address automatically:

Website: www.keennew.com
Qixiang Technology, Contact Us for purchasing Email: [e-mail]
Whatsapp: [phone]
6
2.) Use the following IP address
Configured a static IP address manually within the same subnet of the
router, router default IP address is 192.168.1.1, so static IP address set as
192.168.1.xxx (XXX can be any number between 2 ～254). Subnet set as
255.255.255.0
5. Click OK to finish the configuration.
Router Configuration
1. Log in the Router
To log in to the management page and view the configuration status of your
router, please follow the steps below.
1) On the PC, open a web browser such as Internet Explorer, Google or
Firefox etc.
2) From your web browser, type the IP address of the router into the
address bar and press enter. The default IP address of the router is
192.168.1.1, though the actual address may vary.
3) In the login page, enter the username and password, then click Login.
The default username and password are “admin”.

Website: www.keennew.com
Qixiang Technology, Contact Us for purchasing Email: [e-mail]
Whatsapp: [phone]
7
4) After logging in, the home page of the QX310 Router’s web interface is
displayed, for example.
2. Configure the Cellular Connection
There are two methods to dial up for cellular connection of this router.
1) DHCP dial-up (Default)
Click Basic Network > Mobile Network, choose “DHCP client” as the
Protocol, don’t change other default settings, click SAVE & APPLY button.
2) PPP dial-up
When you don’t want to dial up with DHCP, this router also provide PPP
dial-up option. Click Basic Network > Mobile Network, choose “PPP”as
the Protocol, click SWITCH PROTOCOL button, no need to change the
default parameter, click SAVE & APPLY button.

Website: www.keennew.com
Qixiang Technology, Contact Us for purchasing Email: [e-mail]
Whatsapp: [phone]
8
3) Check the cellular connection status
Click System Status > Overview > 3G/4G WAN Status to view the status of
the cellular connection, the details status information will be displayed.
Note:
A) This router support IoT and VPDN card of multiple carriers.
B) Generally, this router will identify APN information automatically. When
dail-up fail with some IoT card and VPDN card, please contact your carrier
and fill in the AP data such as username, password to configure then get
cellular connection.
C) This router support wired connection, the configuration is similar with
cellular network. Click Basic Network > Wired Network > WAN, choose
“DHCP client” (Optional PPPoE, Static address) as the Protocol, click SAVE &
APPLY button.
3. Configure the WiFi Connection
Besides cellular and wired connection, you can choose WiFi Client mode to
connect this router to internet with following steps:
1) Click Basic Network > Wireless Network, click SCAN button
2) Select existing WiFi network, Click JOIN NETWORK
3) Fill in WiFi password in “WPA passphrase”, then click SUBMIT button

Website: www.keennew.com
Qixiang Technology, Contact Us for purchasing Email: [e-mail]
Whatsapp: [phone]
9
4) Protocol as default DHCP, Click SAVE & APPLY button, Router now can
connect to internet via WiFi network
5) Double check WiFi connection status: System Status > Mobile
Network > Overview > Wireless
4. Connect PC and Terminal to Router
There are two methods to connect PC and terminal to router. One is
connect with Ethernet cable, and another is connect through Wireless
Access Point. Please refer to the steps below.
1) Ethernet cable connection (Wired)
Connect an Ethernet cable to the LAN port of the router, and connect the
other end of the cable to your computer or terminal. Obtain an IP address
automatically from “Local Area Connection”, or to configure a static IP
address manually, detail please refer to page 4 “PC Configuration”
2) Wireless Access Point
To log in to the router management page, please refer to Page 6 “Router
Configuration”

Website: www.keennew.com
Qixiang Technology, Contact Us for purchasing Email: [e-mail]
Whatsapp: [phone]
10
Click Basic Network > Wireless Network> Wireless Overview, click EDIT
button
>General Setup, Choose “Access Point” as Mode, fill in ESSID, click SAVE &
APPLY button.
>Wireless Security, recommend choose “WPA-PSK/WPA2-PSK Mixed
Mode” as Encryption, set password in “key”, click SAVE & APPLY button.
When finished, use your computer or terminal scan available Wireless
Access Point, choose your ESSID and key in password, then enjoy the high
speed, stability, flexibility network.
Note: When this router is using WiFi Client Mode to connect internet,
Wireless Access Point is not workable.

Website: www.keennew.com
Qixiang Technology, Contact Us for purchasing Email: [e-mail]
Whatsapp: [phone]
11
CONTACT US:
Email: [e-mail]
WhatsApp: [phone]
GuangZhou QiXiang Technology Co.,Ltd is a professional provider of machine-to-machine (M2M) and Internet of Things (IoT) connectivity products and
services. Qi Xiang has been focusing on providing Industrial Cellular Router, Cellular Serial Modem, Network Print Server, Serial Device Server (DTU), Android
Industrial Motherboard, Embedded Router Board, M2M Cloud Platform, etc.
With the powerful R&D team, efficient manufacturing plant, professional engineer and QA function, our rugged products offer mobile, high speed, reliable,
flexible, 24*7 hours connectivity for multiple fields such as Oil Field, Smart Grid, Smart City, Transportation, Industry Automation, Telco Infrastructure, Retail,
Video Surveillance, etc. Our products had been passed strict quality control according to CCC, CE, ISO 9001 regulations and implemented in many
well-known companies such China Mobile, China Telecom, China Unicom, KingLong Bus, UnionPay, Hive Box, etc.