qleeno QS101 User manual

qleeno rev 102011
Operating Instructions
Read this manual and follow all the Safety Rules and Operating Instructions before using the product.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
!
!WARNING
The owner and/or operator shall have an understanding of the product, its operating characteristics and safety
instructions before operation. For your safety, read, understand, and follow the information provided with and
on this product before using. If the operator is not uent in English, the product and safety instructions shall
be read to the operator in their native language.
SFA Companies, Inc.
10939 N. Pomona Ave. Kansas City, MO 64153
[email protected]
Protect your investment! Register your Qleeno at www.qleenousa.com
Model QS101

2
! DANGER
! CAUTION
! WARNING
NOTICE
SIGNAL WORDS
Indicates situation which, if not avoided,
will result in death or serious injury
Indicates situation which, if not avoided,
could result in death or serious injury
Indicates situation which, if not avoided,
could result in minor or moderate injury
Indicates situation which, if not avoided,
could result in damage to property
!WARNING
• Read, understand and follow all instructions provided with/on this machine.
• Inspect the device before each use to make sure there are no defects or damage. The machine shall not be
used if it has been damaged, isn't working properly, has been subjected to wet conditions or has been left
outdoors.
• This machine requires an extension cord. Do not run over the extension cord. Do not use the machine if the
electrical cord shows signs of damage. Inspect the cord carefully if it becomes twisted, bent, crushed or is run
over. If damage is observed, replace the cord before using Qleeno.
• Do not use Qleeno to remove explosive or ammable materials. It should not be used in a ammable or
explosive environment.
• Do not modify this device mechanically or electrically. Do not attempt to alter or defeat safety devices in any
way.
• Never insert hands, feet or other foreign objects into or close to the brush mechanism while Qleeno is in operation.
Always make sure the machine is disconnected when inspecting the rotating brush mechanism.
• Qleeno should only be used by properly trained operators.
• Ensure wheel height is properly adjusted and machine does not pull in any direction.
TABLE OF CONTENTS
Warnings 2
Safety and General Information 4
Product Description and Specications 4
Preparation 5
Operation 7
Troubleshooting and Maintenance 8
Replacement Parts 11
Warranty 12
Serial No. _______________________ Date of Purchase ________________________

3
!WARNING
• If using detergents with Qleeno, follow all instructions from the manufacturer. Use only non-foaming
detergents.
• As much as practical, operate Qleeno on a surface clear of obstructions and other people. Use in well-lit
areas.
• Qleeno is only suitable for use on at surfaces, and is not for use on stairs.
• The operator should always remain behind the machine while in use.
• Do not release the handle while Qleeno is running. Always maintain positive control of the machine. Always
turn off the machine when not in use.
• Keep children away from this equipment. Qleeno is not a toy and may be dangerous in the hands of an
untrained user.
• Never leave the machine unattended while the electrical cord is connected to a power source.
• Exercise caution when operating Qleeno around tables and shelves where there is a risk of falling objects.
• Always turn Qleeno completely off and disconnect it from the power source when not in use or before storing,
making adjustments, changing brushes, performing any type of cleaning, maintenance, or repair work.
• Disconnect electrical power by pulling on the plug, not the cord.
• When performing maintenance specified in this manual, follow all instructions. Use of unauthorized
parts or failure to follow maintenance instructions may result in injury and damage to property.
• Maintenance or service other than prescribed in this manual must be performed by qualified repair
personnel.
!CAUTION
• Do not use or store Qleeno outdoors. Do not store in a wet or damp environment.
• Always turn off machine completely when not in use.
• Do not place, transport or store items on top of Qleeno. Do not use without the motor cover in place.
• It is recommended that an annual inspection be done by qualied personnel.
• Use only original, manufacturer approved replacement parts.
• Never use or store Qleeno in temperatures under 32° F/0° C. Liquid left in the reservoir may freeze. Empty
reservoir completely if transporting Qleeno through environment with possible freezing conditions.
• Only use brushes and accessories recommended by the manufacturer. Use of non-approved equipment may
adversely affect function and safety of the machine.
• Vacuum or sweep the surface of loose objects prior to using Qleeno. The Qleeno suction system is designed
for water only.
• Do not use or store this device near strong magnetic elds (such as an MRI machine). Qleeno contains
magnetic materials.
• Ensure that all brushes are properly installed prior to starting the machine.
• Floor coverings should be tested for suitability before using Qleeno. The manufacturer is not responsible for
damage to the machine or ooring if Qleeno is used with improper brush, pad or detergent.
NOTICE

4
SAFETY AND GENERAL INFORMATION
Save these instructions. For your safety, read, understand, and follow the information provided with and on this
product before using. The owner and operator of this equipment shall have an understanding it's safe operating
procedures before attempting to use. The owner and operator shall be aware that use and repair of this product
may require special skills and knowledge. Instructions and safety information shall be conveyed in the operator's
native language before use of this equipment is authorized. If any doubt exists as to the safe and proper use of this
product, remove from service immediately.
Inspect before each use. Do not use if broken, bent, cracked or damaged parts are noted. Any equipment that
appears damaged in any way, or operates abnormally shall be removed from service immediately. It is recommended
that an annual inspection be done by qualied personnel. Labels and Operator's Manuals are available from
manufacturer.
PRODUCT DESCRIPTION
Qleeno is an electric powered, low-prole, wet oor scrubber. It scrubs and dries in one pass, and utilizes water
and any common household oor cleaner. Qleeno is intended for commercial use only and is not a consumer
product.
SPECIFICATIONS
Working width 15 in. (12" pad)
Operating time, per tank 10 - 30 min.
Tank Volume 0.8 gal.
Voltage 230/115V 50/60Hz
Rated Power 1500W
Size (W x L x H) 16-1/2" x 38-7/8" x 7-1/2"
Weight (empty) 66 lbs.
Brush Pressure 26.5 lbs.
Control
Panel
Transport
Wheels
Electrical
Connection
Kick
Stand
Water/Cleaning
Solution Tank
Caster Adjust-
ment Arm

5
PREPARATION
WARNING: Always turn Qleeno completely off and disconnect from power source when making
adjustments, changing brushes, performing any type of cleaning, maintenance, or repair work.
CAUTION: Never use Qleeno without an extension cord, brush or pad holder with pad. Use only accesso-
ries and equipment supplied or recommended by the manufacturer.
Before Each Use
1. Inspect Qleeno to make sure no damage has occurred during transport, storage or previous use.
2. Inspect squeegee ring and change if edges or suction hoses show excessive wear.
3. Inspect brush or scouring pad - replace if necessary.
4. Ensure that correct brush/scouring pad is securely mounted to machine.
5. Adjust casters to proper height (ref. page 6).
6. Fill water tank with fresh water and chemical (if desired).
NOTICE: Follow chemical manufacturer's instructions when using cleaning agent. Use only non-foaming clean-
ing agents.
NOTICE: Qleeno is not intended to be used as a buffer. Do not ll water tank with wax.
NOTICE: After removing water tank, always carry with drain end down - water tank can spill if carried incorrectly.
When replacing, set rear of tank on metal posts in frame side and insert tank ports in matching frame
orices.
NOTICE: Always empty dirty water before each use.
!
!
Place Water tank on metal posts at rear
frame.
Fresh Water Fill
Dirty Water Drain Carry water tank drain end down -
water can leak through ports in front.

6
Mounting the brush/scouring pad
1. With Kick Stand folded up, lift Qleeno to upright (vertical) position and turn brush/scouring pad holder counter-
clockwise to remove it.
2. Mount brush and turn clockwise until it contacts mounting tabs on hub (ref. photo below).
3. If using scouring pad, fasten the pad to the velcro on the pad holder, then mount in same way as brush.
NOTICE: For best results and longer pad life, ensure scouring pad is concentric with holder.
Unfolding the Handle
Unlock handle support locks on both sides of handle, raise handle to desired position and re-lock handle supports.
Handle is adjustable to vertical position or intermediate positions to accomodate the user.
Adjusting the Casters
NOTICE: The Qleeno brush/pad should always operate as close to horizontal as possible, and should not cause
the machine to drag or pull in any direction. Due to normal usage, the casters may require occassional
adjustment.
1. Pull knob on adjustment arm (ref. photo) and raise/lower the caster to desired position.

2. Knob will lock into one of four detents in side of machine.
OPERATION
Starting Qleeno
1. Qleeno requires the use of an extension cord. Handle should be upright and locked.
2. Mount brush or pad holder with scouring pad according to the instructions on previous page.
3. Connect to common household current (110V) electrical outlet via extension cord.
4. Tilt Qleeno backwards slighlty before starting to avoid damaging the scrubber. Start Qleeno by pressing Start/
Stop Scrubber button on control pattern. The machine will perform a brief function test, after which the scrub-
ber, water ow and suction will all commence.
5. Regulate water ow with Decrease Water Flow or Increase Water Flow buttons on control panel. Adjust water
suction with button shown below.
1. Start/Stop Scrubber 3. Decrease Water Flow 6. Start/Stop Suction
2. Scrubber Indicator Light 4. Water Flow Indicator Lights 7. Suction Indicator Light
5. Increase Water Flow 8. Warning Light (red)
Normal Operation
Best results can be obtained by always using a full tank of clean water and chemical (if required). Move Qleeno
in slow, overlapping lines over one portion of the surface at a time.
NOTICE: Change direction slowly - do not move Qleeno in sudden or jerking motions.
Judicious monitoring of water ow should provide the user with approximately 10 - 25 minutes of working time
(low water ow setting - .03 gal/min; med water ow setting - .05 gal/min; high water ow setting - .10 gal/min).
Turning off Qleeno
1. Turn off water ow by pressing Decrease Water Flow button on control panel until all indicator lights go out.
Continue cleaning for ten seconds to collect any excess water.
2. Turn Qleeno off by pressing Start/Stop Suction button on control panel. Suction will continue for an additional
two seconds.
3. Disconnect power cord from power source.
4. Empty dirty water tank.
7
1
2
3
4
5
6
7
8

After Each Use
1. Clean the hub insert and inside of the hub.
2. Empty water tank. Position Qleeno over a oor drain and hold Decrease Water Flow button down for 3 sec-
onds to empty clean water.
3. Clean brush/pad and squeegee ring.
Transporting Qleeno
CAUTION: Do not attempt lifting the entire machine without assistance. If transporting Qleeno a short dis-
tance, simply tilt the machine back on the transport wheels.
1. Unlock handle support locks, fold handle to lowest position and re-lock handle supports.
2. Lift front of machine and roll Qleeno with weight supported on transport wheels.
TROUBLESHOOTING
Symptom Corrective Action
Qleeno will not start • Check electrical connection and fuse.
Control panel Warning Indicator Light is on • Water tank is low. Empty dirty water and rell clean
water.
Qleeno makes beeping sound and shuts off • Water tank is empty. Empty dirty water and rell
clean water.
Water will not ow after starting • Check lters for clogging.
Qleeno leaks water
• Clean water tank seals.
• Verify Water Fill cap is tight and properly threaded.
• Check water pump on.
• Inspect water tank for damage.
Qleeno leaks water when lifted for transport • Check both caps on water tank rmly sealed.
Qleeno drags or pulls in one direction while operating • Adjust casters (see pg. 5)
MAINTENANCE
WARNING: Do not remove the motor cover. Maintenance requiring removal of the cover should only be
performed by a qualied repair technician.
Changing the Fuse
Wait 15 minutes after shutting down before changing the fuse and attempting to restart the machine.
The fuse is a standard 115V/10A, and is located under the control panel, near the electrical connection.
8
!
!

Cleaning the Hub
WARNING: Always turn Qleeno completely off and disconnect it from the power source when not in use or
before storing, making adjustments, changing brushes, performing any type of cleaning, maintenance, or repair
work.
NOTICE: The hub should be cleaned after each use to ensure optimum performance.
1. Turn hub insert clockwise to release bayonet lock.
2. Remove and clean hub insert. Clean inside of hub.
3. To reassemble hub, mate grooves on hub insert with screws around hub, seat insert fully and turn counterclock-
wise to lock in place.
Changing the Squeegee Ring
1. Remove brush or pad holder.
2. Disconnect all three suction hoses from hub.
3. Lift squeegee ring just enough to allow access to nuts on mounting frame.
5. Using an 8mm wrench, remove nuts holding squeegee ring to mounting frame and replace with new ring.
6. To secure squeegee ring, follow steps 1 - 5 in reverse order.
1. Hub 3. Squeegee Ring Mounting Frame 5. 8mm Nut
2. Squeegee Ring 4. Suction Hose
9
4
3
1
25
!

Adjustment of Suction Hoses
NOTICE: Proper adjustment of the suction hoses is essential to good operation. Check hose adjustment on a
regular basis.
1. Pinch hose to allow insertion into squeegee ring.
2. End of suction hose should be approximately 1-3/16" from squeegee ring surface.
Weekly Maintenance
1. Make sure brush rotates freely.
2. Inspect water tank for leaks and that membrane separating clean and dirty water is in good condition.
Monthly Maintenance
1. Perform Weekly Maintenance.
2. Rinse water hoses by cleaning a section of a oor with a large amount of clean water.
3. Thoroughly clean gaskets around water tank.
4. Clean both ll and drain caps on water tank.
5. Clean inside of both clean water and dirty water tank.
After First 100 Hours of Use
Frequency of use and type of environment will dictate when some maintenence is performed. Lubricate casters
with silicone grease or spray. Inspect entire machine for damage, loose screws, nuts and other parts.
Yearly Maintenance
It is recommended that you take your Qleeno to the nearest authorized service center for thorough inspection.
Before long periods of inactivity
1. Perform Monthly Maintenance.
2. Empty machine of all water.
3. Lubricate gaskets with silicone grease.
After long periods of inactivity
1. Inspect gaskets and wipe away excess silicone grease.
2. Perform monthly maintenance.
10
Approximate Critical Component Expected Lifetime
Squeegee 600 hrs.
Vacuum Tube 600 hrs.
Brush 1000 hrs.
AC Motor 1000 hrs.
DC Motor (brush replacement) 2500 hrs.
Timing Belt 1500 hrs.
Water Pump 1500 hrs.
Water Tank 2000 hrs.
Casters 2000 hrs.
Transport Wheels 2000 hrs.

Item Part No. Description Qty
1710-3-9920-107 Hood Assembly Repair Kit 1
2710-4-8700-104 Water Tank Assy (includes parts 3, 4) 1
3710-3-9922-101 Tank Fill (Large) Cap Repair Kit 1
4710-3-9921-109 Tank Drain (Small) Cap Repair Kit 1
5710-6-8706-108 Water Tank Gasket 1
6710-3-9903-107 Fuse Repair Kit (includes 10 fuses) 1
7710-6-8105-102 Water Distributor 1
8710-3-9916-106 Vacuum Tube Repair Kit 3
9710-4-8500-106 Squeegee Ring Assembly 1
10 710-4-8501-108 Brush 1
11 710-3-9902-105 Caster Repair Kit 1
12 710-3-9901-103 Transport Wheel Repair Kit 1
13 710-6-8911-109 Extension Cord, 14 AWG (not shown) 1
14 710-3-9925-107 Safety Labels 3
15 qleeno rev 082011 Owner's Manual 1
For information about Qleeno accessories, go to www.qleenousa.com
9
8
7
1
3
24
6
11
5
12
10
13
REPLACEMENT PARTS
11

SFA Companies, Inc.
10939 N. Pomona Ave., Kansas City, MO 64153
816.891.6390
[email protected]
TWO YEAR LIMITED WARRANTY
Qleeno®, represented in the United States by SFA COMPANIES ("SFA") warrants to the original purchaser that this
product is free from defects in material and workmanship for a period of two (2) years from date of purchase. The warranty is
non-transferable and is subject to the terms, exclusions, and limitations described below:
• Any damage resulting from misuse of neglect including, but not limited to bent squeegee rings, dented or crushed machine
hoods, broken welds or punctured rubber bladders as well as worn out seals, o-rings and springs are the result of misuse and
not covered by warranty and no warranty credit will be provided for such damaged components.
• This warranty does not apply to ordinary wear and tear, overloading, alterations (including repairs or attempted repairs not
performed by SFA or one of its authorized service centers).
• This warranty is voided by improper uid use, or use of the product in any manner for which the product was not intended use of
the product in accordance with the instructions or warnings provided with the product and any modications of the product.
• In the unlikely event that a Qleeno product fails due to material defect in workmanship, you may contact SFA for disposition.
Please contact our customer service department at [phone] before proceeding with shipment or repairs on the product.
In such cases, the customer’s sole and exclusive remedy for any breach or alleged breach of warranty is limited to the repair
or replacement of the defective product.
• Under no circumstances is SFA liable for any consequential such as lost prots or any other incidental damage whatsoever.
• THIS WARRANTY IS LIMITED TO NEW PRODUCTS SOLD THROUGH AUTHORIZED DISTRIBUTORS AND OTHER
CHANNELS DESIGNATED BY SFA. NO AGENT, EMPLOYEE OR OTHER REPRESENTATIVE OF SFA, IS AUTHORIZED
TO MODIFY THIS WARRANTY.
• THE FOREGOING IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FOR A FITNESS FOR A PARTICULAR
PURPOSE. ALL OTHER WARRANTIES ARE EXPRESSLY DISCLAIMED. WARRANTY LAWS IN DIFFERENT LOCALITIES
MAY VERY AND YOU MAY HAVE RIGHTS BY VIRTUE OF STATE OR LOCAL LAW.
• SFA’s, liability in all cases is limited to, and will not exceed the purchase price paid for the product.
• “Wear Items” such as accessories, motor carbon brushes, AC motor, squeegees, brushes, pads, vacuum tubes, wheels, casters,
belts, bearings, and etc. are excluded unless found defective by Qleeno or SFA or an authorized service center.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you. This warranty gives you specic legal rights, and you may also have other rights, which vary from state to
state.