R&B Wire Products 715 User manual

[e-mail] [phone] RBWIRE.COM
ASSEMBLY INSTRUCTIONS
R
TOOLS REQUIRED:
(2) 7/16 wrenches or sockets
STEP
1
Install casters to upright legs by inserting caster
stems into bottom of legs. Insert bolts through side
with flush bolt holes, and secure with nuts on the side
with dimpled bolt holes.
STEP
2
Place crossbar (with warning label side facing up) onto
the side of the wheelbase with nuts. Align the three
vertical holes and secure with partial-thread bolts and
nuts, with nuts on underside. Then secure horizontal holes
with four partial-thread bolts. Nuts should be on the same
side as crossbar. Repeat for other side.
WARNING
!
MODEL 715/721 and 722/725
Portable Garment Racks
2 person assembly suggested
· Never allow children (or adults) to ride on or swing from garment rack
· Keep casters free of thread, lint, hair and other debris. Be sure casters turn easily and roll freely
at all times. If a caster does not roll properly, remove the garment rack from service immediately.
· Periodically check all nuts and bolts to ensure they are tight.
· Weight limit 175 lbs. — Do not overload!
· Be sure all loads are evenly balanced at all times. Overloading or unbalanced loads may cause
tipping, resulting in serious injury.
· Always proceed slowly and use extra caution when turning corners.
715, 721 HARDWARE INCLUDED (Not to scale)
x28 Nuts
x24 Partial-thread boltsx4 Full-thread bolts

[e-mail] [phone] RBWIRE.COM
ASSEMBLY INSTRUCTIONS
R
pg 2
MODEL 715/721 and 722/725
Portable Garment Racks
STEP
3
Model 715/721: With upper horizontal crossbar resting
and centered on top of uprights, align the three vertical
holes at each end and secure with three partial-thread
bolts and nuts, nuts on the underside. Then secure
crossbar at each end with two partial-thread bolts and
nuts through the two center holes, nuts on inside.
Model 722/725: Position one upper crossbar as pictured,
with flush side of triangular support facing out. Align
crossbar and upright holes and secure with two partial-
thread bolts on each side, with nuts on the side of
triangular support. Repeat for other crossbar.
NOTE: Be sure all bolts and suts are securely tightened.
Your Portable Garment Rack is ready for use.
If you have purchased the Basket Shelf Accessory, please continue
onto page 3.
WARNING
!
· Never allow children (or adults) to ride on or swing from garment rack
· Keep casters free of thread, lint, hair and other debris. Be sure casters turn easily and roll freely
at all times. If a caster does not roll properly, remove the garment rack from service immediately.
· Periodically check all nuts and bolts to ensure they are tight.
· Weight limit 175 lbs. — Do not overload!
· Be sure all loads are evenly balanced at all times. Overloading or unbalanced loads may cause
tipping, resulting in serious injury.
· Always proceed slowly and use extra caution when turning corners.
722, 725 HARDWARE INCLUDED (Not to scale)
x26 Nuts
x4 Full-thread bolts
WARNING
!
x22 Partial-thread bolts

[e-mail] [phone] RBWIRE.COM
ASSEMBLY INSTRUCTIONS
R
STEP
1
STEP
2
STEP
3
Basket Shelf Accessory Installation:
Remove bolt and nut in center of lower crossbar at
both ends.
Place one half of basket on top of lower crossbar
so that hole in basket lines up with hole in center
of crossbar at one end. Replace bolt and nut through
basket and crossbar.
Take other half of basket and slide male connector end
into female connector end so that it rests on crossbar.
Align hole in basket with hole in crossbar and replace
bolt and nut.
pg 3
MODEL 715/721 and 722/725
Portable Garment Racks