RapidX Ferrino Installation guide

Place cardboard or drop cloth under chair to prevent damage to
floor during assembly. Make sure the seat back adjuster on the
seat base is set at 90 degrees (as shown in step 1)
Five-star base x 1
Allen keys x 1
M8 screws x 8
Pre-mounted
M8 screws can be found pre-mounted on the seat back and
base. Refer to steps 1 and 4 for unmounting screws.
90°
90°
1
36
7
Pre Assembly Instructions
Parts
ATTENTION
Assembly Instructions
8
5
1
2
3
4
5
6
7
8
Remove the the four M8 screws from the sides of
the seat back. Align Metal Brackets found on Seat
Base at 90 degrees, place the Seat Back onto the
seat base.
Insert and tighten the four M8 screws.
Place the chair on its side.
Add Side Covers and snap into place. Be sure that
the plastic clip fully lines up with the bracket, as
shown in figure 4G-1. The pegs on the clip must
lineup with the holes in the bracket. Press the
bottom round part of the cover into the hinge area,
and then tapping the top firmly with your palm, as
shown in figure 4G-2.
CAUTION, TO AVOID BREAKING COVER: Do not
attempt to tap the top area of the cover in before
the bottom is in place. Also, only tap after ensuring
the clip is lined up with the bracket, and the bracket
holes are aligned with the bracket pegs.
Remove the four M8 screws from the Seat Base.
Mount the Mechanism on the Seat Base (Make
sure arrow is pointed to the front of the chair and
the handle is on the right side) and attach it using
the four M8 screws.
Insert the Caster Wheels into the 5 Point-Star
Base. Stand on the base. Use one foot to hold
down the base, and press the caster into the slot
with two hands. Then, insert the Gas Lift Piston
into the base and add the Piston Cover.
Next, lower the assembled Seat onto the Base -
you may need assistance if you are unable to lift
the seat by yourself.
Loop the bottom straps of the lumbar support
cushion through the area in between the seat and
the chair back. Loop the top straps through the
eyeholes on the chair back. and clip the two sides
together. Adjust the cushion vertically to your
comfort. loop the top of the headrest pillow over
the top of the chair back.
Visit www.RapidX.io to view the
unboxing and assembly video.
Scan the QR code with your
phone to be taken to the video
landing page.
2
by www.RapidX.ioFor additional help, please email [email protected]
Press this part in first
Then tap this part in
4

Assembly Instructions
Adjust Seat Back Seat Height and Rocking
Mechanism Adjustments
Adjust Armrests
by
www.RapidX.io
12
3
Warnings
Care
To adjust the seat back: lift up on the
Be sure the rocking mechanism is in the
locked position before using the
reclining feature.
handle and adjust to the most comfortable
angle.
Reset to the upright position: lift up on the
handle, gently lean against the seat back
and it automatically returns to the upright
position.
Use the Tilt tension dial to increase or
decrease the rocking tension.
Tilt tension
dial
1. Do not use this chair for purposes other than sitting, do not stand on the seat
2. Do not use chair as a ladder or step stool
3. Only use chair on flat surfaces to prevent turning over
4. This chair is design for single person use, maximum weight 265lbs.
5. Do not use chair to move heavy items
6. Do not use chair near flammable materials
7. Keep out of direct sunlight
8. Do not use chair near fire or in damp environments
9. Do not dismantle gas piston
10. Do not use the recline feature while rocking mechanism is engaged.
Do not lift feet off the ground when the seat back is completely lowered
Do not push down on the headrest when the seat back is completely lowered
Wipe with a soft dry cloth to clean the chair
To remove stain use a small amount of mild detergent diluted with
hot water, wipe until stain is removed, then dry the chair to remove
excess water and detergent
Lower the seat: Sit down and lift the
handle, the seat automatically lowers.
Raise the seat: Stand up and lift the
handle, the seat automatically rises up.
Unlock Rocking Mechanism: pull handle
to the right.*
Lock Rocking Mechanism: push handle to
the left.*
* Seat cannot be leaning back while performing
lock procedure
Button 1 moves the armrest up and down.
Button 2 slides the armrest side to side.
Button 3 the armrest forward and back.
Armrests also swivel in both directions.
Button 1 Button 2
Button 3
armrest also swivels out
Be sure to LOCK the Rocking Mechanism before using the reclining feature