Ravelli HRB160 User manual

Brochure for
HRB160 model

Brochure for HRB160 model
Stove, support and frame:
stove FRAME
STOVE
stove SUPPORT

Brochure for HRB160 model
Manteinance and cleaning:
Before carrying out any maintenance operation take the following precautions:
- Make sure that the general power switch has been disconnected.
- Make sure that all the parts of the stove are cold.
- Make sure that the ashes have cooled completely.
- Always use appropriate tools for maintenance.
- When you have fi nished maintenance reinstall all the safety guards before using the stove again.
The stove requires little maintenance if a good quality pellet is used. Therefore it is difficult to establish how often the stove needs to be
cleaned. The quality of the pellet and the combustion adjustment are crucial.
Cleaning the combustion chamber:
The stove requires simple but frequent cleaning to guarantee an effi cient yield and correct functioning. Therefore, clean the combustion
chamber every day using a drum-type vacuum cleanermaking sure that the ashes have gone out completely.
COMBUSTION CHAMBER
FIRE POT
Cleaning the re pot:
Clean the fi re pot as described in the dedicated chapter of the instruction manual. Only a clean and tidy fi re pot can guarantee
that the pellet stove will run without any problems. Deposits may form while it is running and these must be eliminated immediately.
Correct, daily cleaning will allow the stove to burn properly and to give a good yield, avoiding problems that in the long term
could require the intervention of a technician to repair the stove.
Fire pot GRATE

Brochure for HRB160 model
INSPECTION HATCH
(NR.1 right side)
INSPECTION HATCH
(NR.1 left side)
GASKETS
How to pull out the insert:
In order to pull the stove out push down the unhooking lever (as shown below in the drawing). In order to pull the stove
back into the fireplace, keep the lever pushed down until the stove completely fits in the fireplace.
Access and cleaning of inspection hatches:
In order to access the inspection hatches, you need to first pull the stove out.

Brochure for HRB160 model
Cleaning of “T” discharge:
Remove the two “M5” screws that fix the inspection
door and the silicone seal to the discharge in order to
access it and carry out cleaning operations.
INSPECTION HATCH
GASKET
PARTS / FREQUECY Everyday every 2-3 days every 30 days every 60-90 days every season
Fire pot
Ash-drawer
Glass
Suction duct
Door gasket
Tube bundle turbolators
Exhaust pipe
Combustion chamber
Suction of pellet tank
Cleaning of the tube bundle:
The cleaning of the tube bundle is an operation to be carried out daily (WHEN THE STOVE IS COLD)
moving 4-5 times TURBOLATORS mounted on the stove (as shown below in the drawing). In order to
access to the turbolators, you need to pull the stove out from the fireplace. In case the optional pellet
drawer has been mounted on the stove, in order to access to the turbolators you only need to pull the
drawer out.
Turbolators

Brochure for HRB160 model
Access to the debimeter and the electric mother board:
In order to access to the debimeter and the mother board, pull the stove completely out along the entire lenght of the tele-
scopics guides.
DEBIMETER
MOTHER BOARD
Position of automatic air valve
This hydraulic component is placed on the LEFT side of the stove. In order to access the automatic air valve, pull the stove
out.

Brochure for HRB160 model
The cable tightener (optional)
Placed on the rear part of the support, the cable tightener is designed to avoid that, on extracting
the stove, the power supply cable falls between the base of the stove and the support surface of the
stove, resulting in damage and disconnection.
Cable tightener
Assembly of front pellet loading drawer (optional)
Remove the four upper components of the hopper.
Remove the front grate.

Brochure for HRB160 model
Fix the drawer grate and pull the drawer in the dedicated space (as shown below in the drawing).
In order to load the hopper of the frontal drawer, open the drawer pulling the frontal grate. Then load
the pellet and push the pellet inside the hopper using the little shovel supplied togheter.
Assembly of lateral pellet loading kit (optional)
Remove the four upper components of the hopper.

Brochure for HRB160 model
Mount the pellet loading kit and its support as shown below in the drawing:

Brochure for HRB160 model
Frontal view of the stove after having mounted the lateral pellet loading kit. Maximum dimensions are
indicated below.

