Razor RIPSTIK RUSH User manual

TM
OWNER’S MANUAL
Read and understand this entire manual before allowing
child to use this product! For assistance contact Razor.
DO NOT RETURN TO STORE.
NOTE: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect exact appearance of actual product.
Specifications subject to change without notice.
Please have your product along with the 19 character product I.D. code with you
before contacting Razor for warranty assistance and/or replacement parts.
Product I.D. Code: _____________ - ____________ - ____________
NOTE: The unit must be traveling at least 3 mph (5 km/h) before motor will engage.
Kick to start to at least 3 mph (5 km/h) while applying the throttle to engage motor.

11
CONTENTS
Safety Warnings.............................................................................................1-2
Before You Begin...............................................................................................3
Assembly and Set-Up.................................................................................... 4-5
Charging the Battery.........................................................................................6
Pre-Ride Checklist .............................................................................................6
Usage .................................................................................................................7
Repair and Maintenance............................................................................... 8-9
Troubleshooting Guide ....................................................................................10
Warranty and Contact Information ................................................................14
SAFETY WARNINGS
WARNING: Riding a RipStik Rush does present potential risks and
caution is required. Like any riding product, a RipStik Rush has inherent
hazards associated with its use (for example, falling off or riding it into a
hazardous situation). Like any riding product, the RipStik Rush can and is
intended to move and it is therefore, of course, possible to lose control
or otherwise get into dangerous situations. Both children, and adults
responsible for supervising them, must recognize that if such things occur, a
rider can be seriously injured or die even when using safety equipment and
other precautions. RIDE AT YOUR OWN RISK AND USE COMMON SENSE.
WARNING: PARENTAL AND ADULT RESPONSIBILITY AND
SUPERVISION IS NECESSARY: Because products, like the RipStik Rush,
can and do present potential hazards plainly associated with their use, it is
well recognized THE NEED FOR EXERCISE OF PARENTAL RESPONSIBILITY
IN SELECTING RIDING PRODUCTS APPROPRIATE TO THE AGE OF A CHILD,
OR PARENTAL SUPERVISION IN SITUATIONS IN WHICH CHILDREN OF
VARIOUS AGES MAY HAVE ACCESS TO THE SAME RIDING PRODUCTS, IS
IMPORTANT. Not every product is appropriate for every age or size of child,
and different age recommendations are found within this category of product
which are intended to reflect the nature of the hazards and the expected
mental or physical ability, or both, of a child to cope with the hazards.
WARNING: NOT FOR RIDERS UNDER AGE 9 OR HEAVIER THAN
143 LB (65 KG). DO NOT EXCEED THE WEIGHT LIMIT OF 143 lb (65 kg)
– including backpacks and other items that might be carried. Exceeding the
weight limit could injure the rider and damage the RipStik Rush. Rider weight
alone also does not necessarily mean a person’s size is appropriate to fit
or maintain control of the RipStik Rush. Keep this product away from small
children and remember that this product is intended for use only by persons
who are, at a minimum, completely comfortable and competent while
operating the product.
Razor recommends that children under the age of 9 not be permitted to
use this product. This recommendation is based not just on age or weight
or height; it reflects consideration of expected maturity and skills as well
as physical size. The recommended rider age of 9 years or older is only an
estimate and can be affected by the rider’s size, weight, or skills – not every
rider 9 years old or older will be suited to the product. Certainly, any rider
unable to fit comfortably on the RipStik Rush should not attempt to ride it,
but a parent’s decision to allow his or her child to ride this product
should be based on the child’s maturity, skill, and ability to follow
rules. Razor emphasizes that adults are strongly advised not to
disregard Razor’s recommendations or permit younger children to
ride the RipStik Rush.
Keep this product away from small children and remember that it is
intended for use only by persons who are, at a minimum, completely
comfortable and competent while operating.
Persons with any mental or physical conditions that may make them
susceptible to injury, impair their physical dexterity or mental capabilities
to recognize, understand, and follow safety instructions and to be able to
understand the hazards inherent in the use of any ride-on product, should
not use or be permitted to use products inappropriate for their abilities.
Persons with heart conditions, head, back or neck ailments (or prior surgeries
to these areas of the body), or pregnant women, should be cautioned not to
operate such products.
DO NOT EXCEED THE WEIGHT LIMIT OF 143 lb (65 kg). Rider weight
does not necessarily mean a person’s size is appropriate to fit or
maintain control of the RipStik Rush.
CHECK AND MAINTAIN PRODUCT CONDITIONS
Before use, check to confirm that covers and guards are in place and in
serviceable condition. Check that the wheels are free of flat spots from
wear. The product should be maintained and repaired in accordance with
the manufacturer’s specifications, using only the manufacturer’s authorized
replacement parts, and should not be modified from the manufacturer’s
original design and configuration.
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Always check and obey any local laws or regulations which may
affect the locations where the RipStik Rush may be used. Keep
safely away from cars and motor vehicle traffic at all times. Only use
where allowed and with caution.
Do not activate the remote unless you are on the RipStik Rush and
in a safe, outdoor environment suitable for riding. The RipStik Rush must
be moving at least 3 mph (5 km/h) with the lever on the remote in
the “Go” position before the motor will engage. To push/kick start the
RipStik Rush before engaging motor, it is recommended that the rider place
forward foot on front deck and push start using rear foot (see page 7).
The normal powered top speed of this product will be approximately 10 mph
(16 km/h), which can be affected by conditions, such as rider weight, inclines
and battery charge level. Avoid excessive speeds that can be associated with
downhill rides.
Ride defensively. Watch out for potential obstacles that could catch your
wheel or force you to swerve suddenly or lose control. Be careful to avoid
pedestrians, skaters, skateboards, scooters, bikes, children or animals who
may enter your path, and respect the rights and property of others.
The RipStik Rush is intended for use on flat, dry surfaces, such as pavement
or level ground, without loose debris, such as sand, leaves, rocks or
gravel. Wet, slick, bumpy, uneven or rough surfaces may impair traction
and contribute to possible accidents. Do not ride your product in mud, ice,
puddles or water. Watch out for potential obstacles that could catch your
wheel or force you to swerve suddenly or lose control. Avoid sharp bumps,
drainage grates, and sudden surface changes.
Do not attempt or do stunts or tricks. The RipStik Rush is not made to
withstand abuse from misuse, such as jumping, curb grinding or any other
type of stunts. Racing, stunt riding, or other maneuvers also enhance risk of
loss of control, or may cause uncontrolled rider actions or reactions.
Never allow more than one person at a time to ride the product.
Do not ride at night or when visibility is limited.
Never use near steps or swimming pools.
Do not allow hands, feet, hair, body parts, clothing, or similar articles to come
in contact with moving parts or wheels while the motor is engaged.

Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer
Service contact information is listed at the back of this manual.
2
Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer
Service contact information is listed at the back of this manual.
2
SAFETY WARNINGS
Do not touch electric motor when in use or immediately after riding.
Never use headphones or a cell phone to talk or text when riding.
Never hitch a ride with a vehicle.
Do not ride your product in wet or icy weather and never immerse in water,
as the electrical and drive components could be damaged by water or create
other possibly unsafe conditions. Never risk damaging surfaces, such as
carpet or flooring, by use of a RipStik Rush indoors.
PROPER RIDING ATTIRE
Always wear proper protective equipment, such as an approved safety
helmet (with chin strap securely buckled), elbow pads, kneepads and wrist
guards. A helmet may be legally required by local law or regulation in your
area. A long-sleeved shirt, long pants, and gloves are recommended.
Always wear athletic shoes (lace-up shoes with rubber soles) and keep
shoelaces tied and out of the way of the wheels and motor. Never ride
barefooted or in sandals.
USING THE CHARGER
The charger supplied with the product should be regularly examined for
damage to the cord, plug, enclosure and other parts. In the event of such
damage, the product must not be charged until the charger has been repaired
or replaced.
Use only with the recommended charger.
Use caution when charging.
The charger is not a toy. Charger should be operated by an adult.
Do not operate charger near flammable materials.
Unplug charger and disconnect from product when not in use.
Always disconnect from the charger prior to wiping down and cleaning your
product with damp cloth.
WARNING: AAA BATTERIES This product contains AAA batteries. A
swallowed AAA battery can cause internal chemical burns. Dispose of used
batteries immediately. Keep new and used batteries away from children. If
you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
Batteries included for remote - adult attention for installing, changing and
disposal.
Batteries should only be installed or replaced by an adult.
Loose batteries could present a choking hazard and should be kept away
from small children.
Dispose of batteries properly.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE
WARNINGS FURTHER INCREASES RISK OF SERIOUS INJURY. USE
AT YOUR OWN RISK AND WITH APPROPRIATE AND SERIOUS
ATTENTION TO SAFE OPERATION. USE CAUTION.

33
BEFORE YOU BEGIN
WARNING: DO NOT USE
NON-RAZOR PRODUCTS WITH
YOUR RAZOR RipStik Rush. The
RipStik Rush has been built to
certain Razor design specifications.
The original equipment supplied
at the time of sale was selected
on the basis of its compatibility
with the frame and all other parts.
Certain aftermarket products
may not be compatible and will void
the warranty.
Note: RipStik Rush must be
moving at least 3 mph (5 km/h)
while holding the lever on the
remote in the “GO” position for
motor to engage.
Product ID Locations:
(See locations to the left)
1. Underneath Product
2. Charger
3. UPC Side of Box (Not Shown)
Box Contents:
• RipStik Rush
• Remote
• Two (2) AAA Batteries
• Charger
• Owner’s Manual
Remove contents from box. Remove the separators that protect the components from damage during shipping.
Inspect the contents of the box for scratches, or dents that may have occurred during shipping. Because the RipStik
Rush was 99% assembled and packed at the factory, there should not be any problems, even if the box has a few
scars or dents.
MAKE SURE POWER BUTTON IS TURNED “OFF” BEFORE CONDUCTING ANY ASSEMBLY OR
MAINTENANCE PROCEDURES.
Estimated Assembly and Set-Up Time
Allow up to 5 minutes for assembly, not including initial charge time.
Allow up to 6 hours for charge (see page 6 for charging information).
Battery
Remote
On/Off Button
360°
Inclined
Rear Caster
Urethane
Wheel
Remote Holster
Hub Motor
2.
Charger
(Note: Charger design may
vary from one shown)
1.
Charger Port

44
ASSEMBLY AND SET-UP
Installing and Replacing Remote Batteries
Tool Required: Phillips Screwdriver (not included)
Remote Pairing Confirmation
Note: Your remote should have been paired with your RipStik Rush at the factory.
1Using a Phillips screwdriver,
loosen the screw from the top of
battery cover. Remove the battery
cover and set aside.
Note: When installing the batteries,
please pay attention to the batteries’
positive and negative side which must
align with the positive and negative
markings in the battery housing.
1Turn the power switch on the
remote to the ON position.
2 To install batteries, insert two (2)
AAA batteries (included) into battery
housing. If replacing batteries,
remove and discard the old batteries
before inserting new batteries.
2Press power button on the
product to the ON position.
If the power button on the product is
solid red, then the product has been
successfully paired at the factory
and no further steps are needed.
3Replace the battery cover
and tighten the screw using a
Phillips screwdriver.
3 If power button on product is
flashing, leave power button on the
product in the ON position. See
Pairing the Remote section on page 5
for pairing instructions.
WARNING:
• AAA batteries included for
remote - adult attention for
installing, changing and disposal.
• Batteries should only be installed
and replaced by an adult.
• Loose batteries could present a
choking hazard and should be kept
away from small children.
• Do not mix old and new batteries.
• Do not mix alkaline, standard
(carbon-zinc) or rechargeable
(ni-cad, ni-mh, etc.) batteries.
• Dispose of batteries properly.
Note: Batteries are not covered
under the Limited Warranty.

Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer
Service contact information is listed at the back of this manual.
5
Pairing the Remote
1Turn the power switch on the
remote to the OFF position.
4 If the light on the power button on
the product is SOLID, your remote
has been successfully paired.
2Press the power button on the
product to the ON position for
about 2-3 seconds. The light on
the power button should now be
flashing quickly.
5If the light on the power button
continues to flash quickly, turn the
power switch on the remote to the
OFF position and repeat steps 2-3
until the remote is paired.
3Move the lever on the remote
to the STOP position and HOLD.
Do not let go of the lever. Turn the
power switch on the remote to the
ON position.
Note: Contact Customer Service
if you experience any issues with
pairing the remote.
ASSEMBLY AND SET-UP
Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer
Service contact information is listed at the back of this manual.
5

6
2Note: Make sure power button is
in the OFF position. Plug the charger
into the charger port. The light on
the charger should turn red during
charging. The light will turn green
again when charging is complete.
1Plug the charger plug into wall
outlet. The light on the charger
should be green.
Note: If green light (LED) does not
turn on, try a different outlet.
Charger
(Note: Charger design may vary from
one shown)
WARNING: Use ONLY
with the recommended charger.
Batteries are only to be charged
under adult supervision. The charger
is not a toy. Always disconnect the
charger before wiping down and/
or cleaning the RipStik Rush with a
damp cloth.
The charger supplied with the
RipStik Rush should be regularly
examined for damage to the
cord, plug, enclosure and other
parts. In the event of such damage,
the RipStik Rush must not be
charged until it has been repaired
or replaced.
Chargers have built-in overcharge
protection to prevent battery from
being overcharged.
Wall outlet - Green (stand by)
Wall outlet and product -
Red (charging)
Wall outlet and product -
Green (charged)
Note: Continue charging product
even if light turns green prior to
6 hours.
WARNING: Battery charge
can deplete over time. Periodically
recharge battery when not in use.
Your RipStik Rush may not have a fully charged battery; therefore you must charge the battery prior to use. Be sure to
charge the battery in a clean, dry location away from direct sunlight, flames or sparks.
• Initial charge time: 6 hours.
• Recharge time: up to 5 hours, even if the light
turns green. Recommended maximum charging
time is 24 hours.
• Always charge the battery immediately after riding.
• Fully charge battery before storing for extended
periods of time.
• Unplug charger from the wall outlet when not in use.
• Failure to recharge battery periodically may result in a
battery that will not accept a charge.
• Make sure the power button is turned OFF when
product is not in use. If the power button is left on for
an extended period of time, the battery may reach a
stage at which it will no longer hold a charge.
• Run time: Up to 40 minutes of continuous ride time.
Run time may vary depending on riding conditions,
rider weight, climate, and/or proper maintenance.
• Constant starting and stopping may shorten ride time.
• Battery life can vary depending on proper
maintenance and usage of the unit.
• Do not charge at or below 32°F (0°C).
• Do not allow charger or battery pack to overheat. If
they seem warm, allow to cool down. Charge only at
room temperature.
• Do not place product or charger in the sun or warm
environment. Keep at normal room temperature.
LED light
Charger
Model Voltage
(Nominal) Vdc
Capacity
(Nominal) Ah
Charge
Temperature Range
Operating
Temperature Range
RipStik Rush 21.6 2.5 0° to 45°C
32° to 113°F
-20° to 60°C
-4° to 140°F
PRE-RIDE CHECKLIST
Wheels
Periodically inspect the wheels for excessive wear.
Frame
Check for cracks or broken connections. Although broken
frames are rare, it is possible for an aggressive rider to run into
a curb or object and wreck, crack or break a frame. Get in the
habit of inspecting your product on a regular basis.
Hardware/Loose Parts
Before every ride, check all parts, such as nuts, bolts,
fasteners, etc., to ensure they are secure and assembled
correctly. There should not be any unusual rattles or sounds
from loose parts or broken components. If the product is
damaged, do not ride. Reference “Safety Warnings” on
pages 1 and 2 of this manual.
Safety Gear
Always wear proper protective gear, such as an approved
safety helmet. Elbow pads, kneepads and wrist guards are
recommended. Always wear athletic shoes (lace-up shoes with
rubber soles) and keep shoelaces tied and out of the way of the
wheels, motor and drive system. NEVER RIDE BAREFOOTED OR IN
SANDALS.
Laws and Regulations
Always check and obey any local laws or regulations.
Insurance
Do not assume that your existing insurance policies necessarily
provide coverage for product use. Check with your insurance
company for information regarding insurance.
Storage
Prolonged exposure to UV rays, rain and the elements
may damage the enclosure materials, store indoors when not
in use.
6
CHARGING THE BATTERY

Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer
Service contact information is listed at the back of this manual.
7
Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer
Service contact information is listed at the back of this manual.
7
USAGE
How to Ride
Do not activate the remote unless you are on the RipStik Rush and in a safe, outdoor environment suitable
for riding.
Turn power button to the “ON” position for both the RipStik Rush and the remote.
Place one foot on the front deck plate and with the other foot, push (kick start) RipStik Rush while holding the lever
on the remote in the “GO” position. Place other foot on rear deck plate once motor has engaged.
How to Stop
The RipStik Rush, like regular RipStiks or skateboards does not have a conventional “brake”, however the RipStik Rush
can coast to a stop or can use “dynamic motor braking” to slow more quickly.
1While riding, release the
remote lever and it will return to
the “NEUTRAL” position. The
product will slow to a stop with
motor resistance.
Note: Stepping off the product also works to stop. Releasing the remote
lever will cut power to the motor.
2To slow more rapidly to a stop,
move the remote lever down to the
“STOP” position and hold. This will
engage dynamic motor braking
and the product will slow down
more quickly.
Note: Practice riding only in wide
open areas clear from curbs,
parking blocks and other obstacles.
Impacting the wheels against
any hard surface can damage the
wheels. Wheels are not covered
under the limited warranty.
Note: RipStik Rush must be
moving at least 3 mph (5 km/h),
with lever on remote in GO
position, for motor to engage.
Note: As an additional safety
feature, the RipStik Rush is designed
to cut power to the motor when the
lever on the remote is in the “STOP”
or neutral position.
Note: Motor will re-engage,
(without having to kick start), if
the remote is in the “GO” position
before RipStik Rush has slowed
down to under 3 mph (5 km/h).

Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer
Service contact information is listed at the back of this manual.
88
Before beginning repair or maintenance:
• Read the instructions
• Disconnect charger
• Turn the power button OFF
• Exercise caution around
exposed parts
• Contact Razor Customer
Service if unsure about any
repair or maintenance
REPAIR AND MAINTENANCE
Rear Caster Wheel Replacement
Tools Required: Two (2) 5 mm Allen Wrenches (not included)
Rear Caster Replacement
Tools Required: Phillips Screwdriver and 24 mm Socket Wrench (not included)
1Turn product over. Using two (2)
5 mm Allen wrenches, loosen
coupling bolt and remove wheel
from caster.
1Turn product over. Using a Phillips
screwdriver, remove the three (3)
screws attaching the deck plate to
the platform.
2Insert replacement wheel
into caster.
Note: Make sure all three (3)
spacers are aligned with the holes
in the bearings before inserting
the coupling bolt. Secure tightly
into place.
2Turn product over. Using a 24 mm
socket wrench, loosen the nut on the
caster and remove caster.
3 Insert replacement caster. Secure in
place with nut removed in step 2. Re-
attach wheel to caster (Refer to Rear
Caster Wheel Replacement above).
4Re-attach the deck plate to the
platform with the three (3) screws
removed in step 1.
Wheel
13-1 Coupling Bolt
13-2 Small Spacer (x2)
13-3 Bearing (x2)
13-4 Large Spacer
Caster
6-1 Locknut
6-2 Spring Washer
6-3 Flat Washer
13-1
13-2
13-3
13-4
13-1
13-2
13-3
6-1
6-2
6-3

headline
9
Li-Ion
WARNING: Risk of fire - no user serviceable electric parts.
Battery Care and Disposal
• Do not store in freezing or below freezing temperatures. To properly maintain your battery and ensure maximum
battery life, carefully read the “Charging the Battery” section on page 6 of this owner’s manual.
• Battery pack should not be disassembled, crushed, punctured, opened or otherwise mutilated.
CONTAINS LITHIUM-ION BATTERY PACK. BATTERIES MUST BE RECYCLED.
UL 2271 COMPLIANT
Disposal: Your Razor RipStik Rush uses a lithium-ion battery pack which must be recycled or disposed of in
an environmentally safe manner. Do not dispose of a battery pack in a fire. The battery pack may explode. Do not
dispose of a battery pack in your regular household trash. The incineration, land filling or mixing of batteries with
household trash is prohibited by law in most areas. Return exhausted batteries to a federal or state approved lithium
ion battery recycler.
Charger
The charger supplied with the RipStik Rush should be regularly examined for damage to the cord, plug, enclosure and
other parts and in the event of such damage, the product must not be charged until it has been repaired or replaced.
Use ONLY with the recommended charger.
Wheels
Wheels and drive system are subject to normal wear and tear. It is the responsibility of the user to periodically inspect
wheels for excess wear and replace hub motor as required.
Replacement Parts
The most frequently requested replacement parts are available for purchase at some Razor retail partners. For the
complete selection of replacement parts visit www.razor.com.
Repair Centers
For a list of authorized Razor repair centers:
• Check online at www.razor.com.
• Additional Customer Service contact information is listed on the back of this manual.
In the US and Canada only:
For more information regarding
recycling of rechargeable batteries,
call toll free 1-800-822-8837, or visit
http://www.call2recycle.org
Caution: Do not handle damaged
lithium-ion batteries.
Recycling Lithium-ion
Batteries: Lithium-ion batteries are
recyclable. You can help preserve
our environment by returning your
used rechargeable batteries to the
collection and recycling location
nearest you.
9
REPAIR AND MAINTENANCE

headline
Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer
Service contact information is listed at the back of this manual.
10
TROUBLESHOOTING GUIDE
Problem Possible Cause Solution
Does not work out of the box Unit must be traveling at least
3 mph (5 km/h) before motor will engage
Product not paired with remote
Kick to start to at least 3 mph (5 km/h) while holding the lever on
the remote tn the “GO” position to engage motor.
Check for loose connections/wires underneath the deck plate.
No longer works No lights on charger
Undercharged battery
Battery will not hold a charge
Check power to wall outlet and/or try a different outlet.
Check lights on charger:
Plugged into wall - Green
Plugged into wall & unit - Red (charging)
Plugged into wall & unit - Green (charging complete)
No lights/Blinking lights - Replace Charger
Turn product over. Turn the power switch on the remote and
power button on the product to the ON position. Move the lever
on the remote to the GO position and hold. Manually (use caution)
spin the rear wheel forward. If motor engages - replace battery.
Short run time/runs slow Riders weight
Riding conditions
Battery not fully charged
Old/damaged battery
Do not exceed 143 lb (65 kg) maximum weight limit.
Use only on flat, dry surfaces. Avoid inclines and areas with
heavy debris.
Charge product - refer to page 6 for charging information.
Replace battery.
Charge battery at least once a month when not in use.
For more troubleshooting tips, a list of available replacement parts or to locate an authorized Service Center in your area,
visit our website at www.razor.com or call toll free [phone] to speak to a live Customer Service Representative.
*Unit(s) should be turned OFF and fully charged prior to doing any troubleshooting.
NOTE: All troubleshooting steps should be performed by an adult only.
10

NOTICE: INSURANCE
YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR
ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC
RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED,
YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.

1414
FCC COMPLIANCE
WARRANTY
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this product not expressly approved by Razor USA LLC, could void the user’s authority to operate the equipment.
Razor Limited Warranty
The manufacturer warranties this product to be free of manufacturing
defects for a period of 90 days from date of purchase. This Limited
Warranty does not cover normal wear and tear, wheel, or any damage,
failure or loss caused by improper assembly, maintenance, storage or use of
the electric product.
This Limited Warranty will be void if the product is ever:
• used in a manner other than for recreation or transportation;
• modified in any way;
• rented.
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
Razor does not offer an extended warranty. If you have purchased an
extended warranty, it must be honored by the store at which it was
purchased.
For your records, save your original sales receipt with this manual and write
the serial number below.
__________________________________________
CUSTOMER SERVICE CONTACT INFORMATION
Need Help? Visit our website for product support, a list of authorized service centers in the US and customer service contact information at www.razor.com.
Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service contact information is
listed below:
AMERICAS
Razor USA LLC
P.O. Box 3610
Cerritos, CA 90703
USA
[phone]
Monday - Friday
8:00 AM - 5:00 PM Pacific Time
[e-mail]
EUROPE, MIDDLE EAST, AFRICA
Razor USA LLC (Europe)
Handelsweg 2
2742 RD Waddinxveen
Netherlands
[phone]
[e-mail]
ASIA
Razor USA LLC (Asia)
P.O. Box 3610
Cerritos, CA 90703
USA
[phone]
[e-mail]
UNITED KINGDOM AND IRELAND
Razor USA LLC (UK)
Unit 20
Hartnoll Business Centre
Post Hill, Tiverton
Devon EX16 4NG
UK
[phone]
[e-mail]
AUSTRALIA AND NEW ZEALAND:
Razor USA LLC
P.O. Box 4280
Auburn South
VIC 3122
Australia
[phone] (AU)
+0 800 003 221 (NZ)
[e-mail]
IMPORTED IN JAPAN BY B-PLUS ASIA
CORP.
Razor USA LLC
Kurokawa 3-1, Asaoku,
Kawasaki, Kanagawa
215-0035 JAPAN
[phone] Tel
[phone] Fax
[e-mail]
Printed in China for Razor USA LLC.
Copyright © 2003-2022 Razor USA, LLC. All rights reserved. RipStik®, Razor®and the Razor logo design are among the registered trademarks of Razor USA LLC in the United States and/or select foreign countries. RipStik Rush™
and the RipStik Rush logo design are trademarks of Razor USA LLC.
US_220617