RazorBack Offroad IT FITS User manual
R
A
Z
O
R
B
A
C
K
O
F
F
R
O
A
D
™
OPERATIONS MANUAL
RAZORBACK OFFROAD™
R
A
Z
O
R
B
A
C
K
O
F
F
R
O
A
D
™
Important Information Read Carefully.
Keep This Information for Further Reference.
!
Copyright 2018 Inventive Edge, LLC dba RazorBack Oroad ™ (RBO)
All information contained within this publication is based on the latest product information at the
time of publication. Due to constant improvements in the design and quality of production
components, some minor discrepancies may result between the actual parts and the information
presented in this publication. Depictions and/or procedures in this publication are intended for
reference use only. No liability can be accepted for omissions or inaccuracies. Any reprinting or reuse
of the depictions and/or procedures contained within, whether whole or in part, is expressly prohibited.
Printed in U.S.A.
RBO1018 - “IT FITS™” Spare Tire Mount Operation Manual
DOC CONTROL NUMBER RBO0052
!!
WARNING
! !!
Read, understand, and follow all of the instructions and safety
precautions in this manual and on all product labels.
Failure to follow the safety precautions could result in serious
injury or death.
It is the operator’s responsibility to follow all manufacture’s
recommendations regarding the safe operation of the vehicle.
It is the installers responsibility to follow all manufacture’s
recommendations and instructions regarding safe assembly
and installation of an accessory.
It is up to the installer that each accessory is securely mounted.
Operator must use common sense when using any RBO
accessory and when a loading rack so as not to affect the
vehicle’s safe operation.
The IT Fits Spare Tire Mount is not rated for nor should be
used as a step or hung from.
The IT Fits Spare Tire Mount should not be used as a tie-down
point for hanging items.
We recommend regular inspections and replacement of
faulty O-ring to ensure the Lugs functions as designed and to
prevent loss.
Adding mounts to the side and/or rear of the vehicle increases
its size. RBO highly recommends that you only use the RBO1018
IT FITS Spare Tire Mount on the RBO5040 Polaris RXR®900
Expedition Rack™ (Jim Todd Edition)’s tailgate location.
Ignoring these cautions and warnings could increase the
potential for accidents that could result in serious injury or death.
RAZORBACK OFFROAD™
1
Hello, and welcome to the world of Razorback Offroad™.
Thank you for your purchase of a Razorback Offroad™ (RBO)
Product. As a US-based small company, we want you to know that
each order you place means a lot to us as we grow our worldwide
family of RBO enthusiasts.
We passionately believe RBO sets new standards in UTV accessories
for excellence and design quality. We also take a lot of pride in the
fact that RBO directly creates US jobs in our small town in southern
Idaho. We believe that success is only possible by having great
customers, invested distributors, and an unwavering commitment to
both. We want you to know that we understand that your choice to
own an RBO product makes it all possible for us, and we are grateful
for the opportunity to be the choice you have made for your UTV.
We have always believed in asking ourselves - ”
Are we better today
than we were yesterday?
” to best meet our commitment of constant
improvement we ask that If you like our products, service, or wish
to reach out to us for any reason then please do so. We are always
excited to get feedback from our clients and fanatical customers.
That you would give some of your valuable time to leave a review,
watch a video about our products, visit our website, or even call
or send us a testimonial means a great deal to us.
If for any reason you are not satised with any part of the order,
the process, or our product, please let us know right away. We are
committed to doing everything we can, to make sure you are 100%
satised with all parts of our company and your experience.
Thanks again for choosing RBO and supporting us, our company and
our community!
Razorback Offroad
Mountain Home, Idaho
R
A
Z
O
R
B
A
C
K
O
F
F
R
O
A
D
™
RAZORBACK OFFROAD™
2
RECOMMENDED TOOLS FOR INSTALLATION
( Not Included )
RBO1018 - “IT FITS™” Adjustable Spare Tire Mount
Made here in Idaho, The RBO “It Fits ™” Adjustable Spare Tire Mount is a true industry rst!
With our sliding mounting studs you can easily adjust this mount to accommodate different sized tires
and wheel offsets. Not only did we design this mount to work with 10mm and 12mm wheel lugs we also
include all of the mounting hardware.
When it comes to installation, this mount has our exclusive “It Fits ™” base plate. Just look at any of our
racks and if you see the It Fits Icon you will know this mount will bolt directly onto the rack.
A Warnings
01 Welcome
02 Table of Contents & Product Introduction
03 Parts & Hardware
04 Assembly Instructions
04 Step 1 ......... Determining Length to Set the Mount
04 1.1 Establishing Bore to Surface Measurment
05 Step 2 ......... Setting the Mounting Arm
06 Step 3 .......... Attaching the Base Arm
07 Bore to Surface Measurment Recording Location
08 Step 4 .......... Stud Installation
09 12mm Lugs 4A - 4C
10 10mm Lugs 4A - 4B
11 Final Assembly
12 Warranty
13 Product Registration
14 RBO 100% Money Back Guarantee
15 Return Policy
16 Contact Information
INTRODUCTION:
• Tape Measure
• Impact Gun
• #3 Phillips Screw Driver
• 7/16” End Wrench
TABLE OF CONTENTS:
PAGE
RAZORBACK OFFROAD™
3
HARDWARE:
PARTS:
INCLUDED PARTS AND HARDWARE:
(1)
“IT FITS™” Mounting Arm
(1)
Base Arm for Spare Tire
(8)
¼” x ¾” Phillips
/ Slotted Screw
(2)
12mm Studs
(2)
10mm Lug Nuts
(2)
12mm Lug Nuts
(2)
10mm Studs
(8)
¼” Nylock Nuts
(1)
¼ Flat Washer
(2)
Nut Holders
(2)
3/8” O Rings
RAZORBACK OFFROAD™
4
The following are general instructions for assembling the RBO1018 – “IT FITS™” Adjustable Spare Tire
Mount.
Due to constant improvements in the design and quality of production
components, some
minor discrepancies may result between the actual parts and the information presented.
ASSEMBLY INSTRUCTIONS:
Determining the Length of the “IT FITS™” Adjustable Spare Tire Mount to the Spare Tire:
It is up to the installer to see that any accessory is securely mounted, and any tools used by the installer are used
and/or operated using common sense and that the installer follows the tools manufacturer’s
descriptions for intended use and recommendations.
RBO, its employees, and afliates can assume no responsibility or liability for misuse of tools and/or improper
installations that may result in breakage, damage, injury, and/or death.
!!
ATTENTION
STEP 1
(STEP 1.1)
Set the tire you wish to mount on a at surface
with the inner side facing down.
(STEP 1.2)
Measure from the at surface to the bottom edge
of the wheel’s central bore. This is the minimum
length you will need to have in order to mount
your tire to your “IT FITS™” Adjustable Spare Tire
Mount. See Figure 1. Record this measurement
in the box on page 7 for use in Step 3.3.
FLAT
SURFACE
BASE OF
CENTRAL
BORE
BORE TO
SURFACE
MEASUREMENT
(FIG. 1)
RAZORBACK OFFROAD™
5
Installation of the “IT FITS™” Support Arm
(STEP 2.1)
Place the hardware piece with the “IT FITS™”
Mounting Arm for the Adjustable Spare Tire
Mount against the location on the rack you wish
to install your “IT FITS™” Adjustable Spare Tire
Mount. At this time make sure that the facing of
the arm with the four circular holes and the single
large oval slot is facing upward.
STEP 2
(STEP 2.2)
Once the rack’s “IT FITS™” mounting bracket and
the “IT FITS™” Mounting Arm are aligned, inset a
single 1.4” x 3/4” Phillips/Slotted Screw into each
of the four holes on the “IT FITS™” Mounting
Arm, and then secure each screw with a single
1/4” Nylock Nut.
!!
WARNING
Adding mounts to the side and/or rear of the vehicle
increases its size and may affect the balance and
performance of a vehicle. RBO does not recommend
installing the RBO1018 “IT FITS™” Spare Tire Mount
anywhere but at the tailgate location.
(STEP 2.3)
With the screws and bolts in place RBO recommends
using an impact driver with a #3 Phillips attachment
with a 7/16” wrench to tighten down the “IT
FITS™” Mounting Arm to the rack.
(FIG. 2.0)
(FIG. 2.1)
See Figure 2.0
See Figure 2.1
RAZORBACK OFFROAD™
6
STEP 3
(STEP 3.1)
With the “IT FITS™” Mounting Arm now rmly attached to the rack, take the Base Arm for Spare Tire
and place it on top of the “IT FITS™” Mounting Arm.
The “IT FITS™” mounting
system is designed so that you
can quickly and easily install
onto any RBO rack any RBO
Accessory with the “IT FITS™”
icon onto any RBO Rack.
“IT FITS™” also means that these
accessories come with all the
hardware you need to install
accessories on your RBO rack
without drilling or modifying
your accessory or machine.
The “IT FITS™” mounting system
R
A
Z
O
R
B
A
C
K
O
F
F
R
O
A
D
™
Assembly of the Base arm for Spare Tire to the “IT FITS™” Mounting Arm:
(FIG. 3.0)
See Figure 3.0
RAZORBACK OFFROAD™
7
(STEP 3.2)
Next, measure from the outside edge of the Mounted “IT FITS™” Mounting Arm (Now attached ush
to your rack). Once in place, set the distance equal to the recorded measurement that was taken on
page 4 in step 1.2.
(STEP 3.3)
Move the Base Arm for Spare Tire outward until its outer edge is equal to the distance you have mea-
sured for the Bore to Surface Measurement in Step 1.2. This is the minimum distance you will need to
attach your tire to the “IT FITS™” Adjustable Spare Tire Mount.
WRITE BORE TO SURFACE MEASUREMENT HERE:
Bore to Surface Distance
(FIG. 3.1)
See Figure 3.1
RAZORBACK OFFROAD™
8
(STEP 3.6)
The remaining cap screw, closest to Tire Mount
Plate, will need the single 1/4” Flat washer to be
installed on the underside of the arm before
adding the last remaining 1/4” Nylock Nut to
secure it in place.
(FIG. 3.2)
(FIG. 3.4)
(STEP 3.4)
Continue to slide the Base Arm for Spare Tire
outward until the two holes on the side of the
Tire Mount Plate align with two holes on the “IT
FITS™” Mounting Arm. Once aligned inset, a
single a 1/4” x 3/4” Phillips/Slotted Screw into
three of the four holes on the “IT FITS™” Adjust-
able Spare Tire Mount’s Arms (One on Top and
two on the side).
See Figure 3.2
(STEP 3.5)
Place a 1/4” Nylock nut on the inside of the
channel and screw down each of the two screws
on each side of the arm and then tighten the
single screws closest on the top of the “IT FITS™”
mounting bracket using a single 1/4” Nylock Nut.
See Figure 3.3
(FIG. 3.3)
1
2
3
See Figure 3.4
(STEP 3.7)
With the screws and bolts in place RBO recommends
using an impact driver with a #3 Phillips attachment
with a 7/16” wrench to tighten down each Bolt and
nylock nut.
See Figure 3.3
RAZORBACK OFFROAD™
9
STEP 4
UTVs with a 12mm Lugs:
(12mm - Step 4.1)
Insert the 12mm stud and rotate it so that it rests within the slot in the inner facing of the Tire Mount Plate.
(12mm - step 4.2)
Once the stud is in place/slip a single 3/8” O-ring over the stud’s threads on the opposite side of the
Tire Mount Plate and slide it down until it is touching the Tire Mount Plate. The 3/8” O-ring will then
hold the stud in place within the slot preventing it from falling out, but still allow for the stud to be
adjusted to t multiple-Lug patterns. (See Figure 12mm 4.1)
(12mm - step 4.3)
Once the O-ring is in place, screw on the Lugnuts to completely secure the lug until you are ready to
mount your spare tire.
(We recommend regular inspections and replacement of faulty O-rings to ensure the Lugs functions as designed.)
Stud Installation:
After consulting your owners guide to determine the stud size of your vehicle
use the RBO provided Stud of the correct size (either 10mm or 12mm) and
proceed to the assembly instructions for the specic Stud Size.
(FIG. 12mm 4.1)
ATTENTION
Only one set of O rings is provided in the hardware pack. You may need to remove the
O rings from one set of studs and transfer them to the Lug set you wish to use.
RAZORBACK OFFROAD™
10
UTVs with a 10mm Lugs:
(10mm - Step 4.A)
Insert the 10mm stud into a Nut Holder. (See Figure 10mm 4.1)
(10mm - Step 4.2)
Insert both the stud and nut holder so that it rests within the slot in the inner facing of the Tire
Mount Plate. It is important to note that only when used together will the 10mm stud be prevented
from freely rotating when the stud is nested. (See Figure 10mm 4.2)
(FIG. 10mm 4.2)
(FIG. 10mm 4.1)
RAZORBACK OFFROAD™
11
(STEP 4.2)
Once the O ring is in place you may screw on the Lugnuts to completely secure the stud until you are
ready to mount your spare tire.
(STEP 4.1)
With the Stud and Nut holder in place slip a single 3/8” O ring over the studs threads on the opposite
side of the Tire Mount Plate and slid it down until it is touching the Tire Mount Plate. The 3/8” O ring
will then hold the stud in place within the slot preventing it from falling out but still allow for the lug
to be adjusted to t multiple-Lug Hole positions. (See Figure 4.3)
(FIG. 4.3)
WARNING
RBO recommends that when not transporting a spare tire that the Lugnut is always
used to secure the stud and O-ring. Reliance strictly on the O-ring only will
most likely result in the stud falling out and needing to be replaced.
!!
THANK YOU AGAIN FOR CHOOSING RBO!
RAZORBACK OFFROAD™
12
WARRANTY
Limitation on Warranty
Inventive Edge, LLC dba RazorBack Of-
froad ™ (RBO) warrants to the original
purchaser that each new RazorBack
Offroad™ (RBO) product will be free
from defects in material and workman-
ship for a period of twelve (12) months
from date of purchase.
RBO’s obligation under this warran-
ty, statutory or otherwise, is limited
to the repair or replacement at the
RBO factory, or at a point designated
by RBO, of such part or parts as shall
appear upon inspection by RBO to be
defective in material or workmanship.
In no event shall RBO accept such no-
tication later then twelve (12) months
from date of purchase. This warranty is
not transferable.
Except as expressly set forth in this
warranty, RBO makes no other war-
ranty, express or implied, and hereby
disclaims all other warranties includ-
ing, but not limited to, the implied
warranties of merchantability and
tness for a particular purpose. RBO
shall in no event be liable for claimed
downtime, claimed loss of prots or
goodwill, or any other special, inciden-
tal, indirect, or consequential damages
concerning or relating to any product
or parts, whether based on negligence,
strict liability, breach of contract,
breach of warranty, misrepresentation,
or any other legal theory, regardless
of whether the loss resulted from any
general or particular requirement
which RBO knew or had reason to
know about at the time of sale.
RBO makes no warranty, express or
implied, as to the nished products
manufactured or supplied by another
manufacturer and supplied by RBO to
purchaser, including, but not limit-
ed to, any boat or vehicle to which
an RBO product may be afxed or
any accessories, and RBO expressly
disclaims any implied warranties of
merchantability and tness for a par-
ticular purpose as to such equipment
or products. This language shall in no
way effect or diminish the rights of the
purchaser to rely on such warranties as are extended by such manufacturers or
supplies. RBO shall, to the extent permitted under applicable law, pass on to the
purchaser such manufacturer’s or seller’s warranty.
RBO, who’s policy is one of continuous improvement, reserves the right to im-
prove it’s products through changes in design or materials as it may deem desir-
able without being obligated to incorporate such changes in products previously
sold.
This warranty is not intended to cover or include the following items, which are
set forth by way of example and not limitation:
Normal deterioration of trim, paint, lettering, appearance of items due to wear
or exposure to weather, etc.
Any damage or defect due to accident, misuse, abuse, operation exceeding
rated loads, Improper or unauthorized repairs, failure to provide reasonable and
necessary maintenance, or uses of which the equipment was not designed or
intended.
Alterations or modications that effect performance, operations, or reliability.
Products Covered
All Products carrying the Razorback Offroad ™ (RBO) name. (All other products
purchased from other manufacturers are limited to that manufacturer’s warranty.)
R
A
Z
O
R
B
A
C
K
O
F
F
R
O
A
D
™
RAZORBACK OFFROAD™
13
PRODUCT REGISTRATION
Please ll out the Product Registra-
tion form found on our web site at
(https://razorbackoffroad.com/
product-registration/ )
to register you’re equipment.
By submitting the information within
15 days of you’re purchase, you’re
warranty transfer will be validated, and
it ensures that you’re equipment will
be protected. If we should ever need
to contact you concerning the compli-
ance of you’re registered equipment
with any applicable safety standards,
the information you have provided
on the warranty registration transfer
below will ensure you’re immediate
notication.
RBO 100% Money Back
Guarantee:
The RBO 100% Money back
guarantee pertains to any
Razorback Offroad ™ (RBO)
Branded product purchased
online directly from RBO.
If you are not 100% satised with the
product for any reason, just return
the product back to RBO and RBO will
refund 100% of the purchase price of
the product.
• In order to receive refund for
product return, RBO must be no-
tied in writing or via email within
30 days of product purchase that
user wishes to return product.
• In order for a product to qualify
for the 100% money back guaran-
tee, claim must be led must be
led within 30 days of purchase
date.
• Once the product is returned to
RBO, RBO will send a check to the
user to cover the initial product
cost less freight charges if any.
• This offer does not include freight
or transportation cost (See Return
Policy).
• It is the responsibility of the pur-
chaser to pay all freight charges.
• In no way will RBO be responsible
to refund freight cost to end user.
• If RBO determines that the prod-
uct was blatantly destroyed or
damaged due to negligence of the
purchaser, this refund offer will be
null and void.
• This warranty does not obligate
RBO to bear the cost of labor or
transportation charges in connec-
tion with the repair or replacement
of any parts found to be defective,
nor shall it apply to a product
upon which repairs or alterations
have been made unless authorized
by RBO.
The Purchaser, when returning a Prod-
uct, must follow the following steps:
1. The Purchaser must have proof
of purchase of any damaged
Product. The Purchaser must
obtain from Razorback Offroad
™ (RBO) a Returned Merchandise
Authorization (RMA) will be given
along with the correct address
where to ship the damaged
product.
2. The Purchaser must pay all
shipping costs to deliver the
damaged Products to RBO and
must send the damaged Product
along with the RMA and proof of
purchase together.
3. Upon receipt of damaged Prod-
uct, RBO will determine whether
the damaged Product is covered
under the Limited Warranty.
4. If it is, RBO will repair or replace
the Product.
5. If the Product is replaced, the
Product that is originally returned
by the Purchaser shall become
the exclusive property of RBO.
6. If the returned Product is not
covered under the Limited War-
ranty, RBO will notify the Pur-
chaser before taking any farther
action with regard to repair or
replacement, which would be at
the Purchaser’s cost.
7. The Customer is responsible to
pay shipping charges to RBO for
product inspection. RBO will pay
return freight if product is found
to be under warranty using UPS
Ground or equivalent.
8. If a customer would like to have
they’re product returned over-
night or via rapid freight meth-
ods, RBO will give customer the
option to pay for rapid freight
options.
RETURN POLICY:
ATTENTION
Notice to Owner or User:
It is the responsibility of the Owner
or User to go to our Product
Registration page to register your
RBO product. Failure to register a
product will void any expressed or
implied warranties of RBO products.
Filling out you’re online warranty reg-
istration is very important in the event
that RBO should ever need to contact
you concerning the compliance of
you’re registered equipment with any
applicable safety standards, the infor-
mation you have provided on the war-
ranty registration transfer below will
ensure you’re immediate notication.
User should also read and understand
all operations manuals pertaining to
the product purchased. User should
also consult with all manufacturers
operations manuals regarding the
addition of aftermarket products to
they’re machines to make sure that
RBO products can be used without
affecting the machine’s performance
and handling. When in doubt please
consult with you’re local UTV dealer.
R
A
Z
O
R
B
A
C
K
O
F
F
R
O
A
D
™
PH: (208) 696-7230 FAX: (208) 580-1900
inventive edge, LLC 3190 Industrial Way, Mountain Home, ID 83647
RBO0052
This manual suits for next models
1
Table of contents
