AFX MOTORSPORTS CAN AM MAX X3 User manual

INSTALLATION MANUAL
CAN AM MAX
X3
SPORT ROOF RACK
SKU CAN006-S
[email protected]
THIS PRODUCT IS FOR OFF ROAD USE ONLY
Place the central bar over the Bracket aligning it with the
perforations, as it is shown in the image, hold it using a 1/4 x
3/4” screw with the washer and nut. (Repeat this step on both
driver’s and passenger’s side)
Tighten all the screws to nish with the installation.
13
12

AFX
Motorsports
products
are
designed
to
best
fit
user’s
ATV/UTV
under
stock
conditions.
Adding,
modifying,
or
fabricating
any
factory
or
aftermarket
parts
will
void
any
warranty
provided
by
AFX
Motorsports
and
is
not
recommended.
AFX
Motorsports
products
could
interfere
with
other
aftermarket
accessories.
If
user
has
aftermarket
products
on
machine,
contact
AFX
Motorsports
to
verify
that
they
will
work
together.
Although
AFX
Motorsports
has
thousands
of
satisfied
customers,
user
should
be
aware
that
installing
bumpers,
rock
sliders,
spare
tire
carriers,
etc.
will
change
the
ride
of
machine
and
may
increase
maintenance
and
part
wear.
Operating
any
off-road
machine
while,
or
after,
consuming
alcohol
and/or
drugs
increases
risk
of
bodily
harm
or
death.
No
warranty
or
representation
is
made
as
to
this
product’s
ability
to
protect
user
from
severe
injury
or
death.
AFX
Motorsports
urges
operators
and
occupants
to
wear
a
helmet
and
appropriate
riding
gear
at
all
times.
By
purchasing
and
installing
AFX
Motorsports
products,
user
agrees
that
should
damages
occur,
AFX
Motorsports
will
not
be
held
responsible
for
loss
of
time,
use,
labor
fees,
replacement
parts,
or
freight
charges.
AFX
Motorsports,
nor
any
3rd
party,
will
not
be
held
responsible
for
any
direct,
indirect,
incidental,
special,
or
consequential
damages
that
result
from
any
product
purchased
from
AFX
Motorsports.
The
total
liability
of
seller
to
user
for
all
damages,
losses,
and
causes
of
action,
if
any,
shall
not
exceed
the
total
purchase
price
paid
for
the
product
that
gave
rise
to
the
claim.
AFX
Motorsports
will
warranty
only
parts
provided
by
AFX
Motorsports.
Any
damage
or
problems
with
OEM
housings,
bearings,
seals,
or
other
manufacturers’
products
will
not
be
covered
by
AFX
Motorsports.
AFX
Motorsports
parts
and
products
are
not
warrantied
if
item
was
not
installed
properly, misused, or modified.
Liability Statement
5/32” Allen Key.
7/16” Combination Wrench.
(48x) 1/4” x 1/2” Bolts with nuts.
SPORT ROOF RACK
HOW TO INSTALL
FOR PURCHASING AT AFX MOTORSPORTS
(12x) 1/4” x 3/4” Bolts with nuts.
10
Central Bar
Front Roof Rack
Rear Legs
Frontal legs
Bracket
Rear Roof Rack
Front Roof Rack
Passenger’s side: Align Bracket at the front part of the roof rack
with the perforations, (as it is shown in the image), hold it with
a 1/4 x 1/2" screw using the washer and nut provided (Do not
tighten)(Repeat this step in the Driver´s Side)
Now, settle the front part of the roof rack over the front legs,
using a 1/4 x 1" screw using the washer and nut provided. (Do
not tighten yet)
Front Roof Rack
11
(6x) 1/4 x 1 ” Bolts with washer and nuts.

Check that the central perforations match, use three 1/4 x 3/4”
screws with the nut it is shown in the image. (Do not thighten
yet)
Hold the front leg of the passenger´s side aligning it with the
leg at the rear from the passenger´s side.
8
9
NOTE: Just in case you have the Flat Roof start from step 5.
Settle the part at the rear of the Roof Rack over the legs at the
rear that were installed before, using a 1/4 x 1”screw using the
washer and nut provided. (Do not tighten yet)
Rear Roof Rack
Align 3 central rails with the perforations (as it is shown in the
image). Use sixteen 1/4 x 1/2” screws with nut, inserting them
bottom-up. (Do not tighten yet). Central Rail
3/16 x 1/2 “ screw

3
4
5
6
Settle the leg over the roof (Only with he Original Roof), place
a washer over the perforations as it is shown in the image,
using 1/4 x 1” screws. (Do not thighten yet)
7
Repeat steps from 1 to 3 on the
driver’s side and tighten all the
screws.
1/4”Washer
1/4 x 1” Screw
1/4” nut
1/4”Washer
1/4 x 1” Screw
1/4” nut
Install rear frame assembly onto rear side rails (as it is shown in
the image). Use four 1/4x 1/2”screws with nut. (Do not tighten
yet).
Rear Roof Rack
1/4 x 1/2” Screw
Nuts
Laterals
Align 3 central rails with the perforations (as it is shown in the
image). Use twelve 1/4 x 1/2”screws with nut, inserting them
bottom-up. (Do no tighten yet)
1/4 x 1/2” Screw
Central rail
Install Front frame Assembly onto front side rails (as it is
shown in the image). Use four 1/4 x 1/2” screws with nut (Do
not tighten yet).
Laterals
1/4x 1/2 “ screw