Cornwell Tools CSE-4000TS User manual

CSE-4000TS 1Rev. 6/18/03
• Operating Manual
• Warning Information
• Parts List
CSE-4000TS
4000 Lb.
Tripod Stand
THIS OPERATING
MANUAL CONTAINS
IMPORTANT SAFETY
INFORMATION.
READ CAREFULLY
AND UNDERSTAND
ALL INFORMATION
BEFORE OPERATING
THIS TOOL.
SAVE THIS MANUAL
FOR FUTURE USE.
THIS UNIT IS AN ACCESSORY STAND
ONLY AND IS NOT DESIGNED OR
INTENDED TO SUPPORT VEHICLES.
DO NOT OVERLOAD STAND. OVER-
LOADING CAN CAUSE DAMAGE TO, OR
FAILURE OF, THE STAND.
PLACE LOAD IN THE CENTER OF THE
SADDLE ONLY. LOADED STAND MUST BE
STABLE BEFORE PROCEEDING WITH
WORK.
A VISUAL INSPECTION SHOULD BE
MADE BEFORE EACH USE OF THE
STAND, CHECKING FOR CRACKED,
DAMAGED, LOOSE OR MISSING PARTS.
USE STANDS ON HARD LEVEL SURFACE
CAPABLE OF SUSTAINING THE LOAD.
USE ON OTHER THAN HARD LEVEL
SURFACES MAY RESULT IN POSSIBLE
LOSS OF LOAD.
NO ALTERATIONS TO THE STAND SHALL
BE MADE.
READ, STUDY AND UNDERSTAND THE
INSTRUCTION MANUAL PACKED WITH
THIS STAND BEFORE USING STAND.
FAILURE TO HEED THESE WARNINGS
MAY RESULT IN LOSS OF LOAD,
DAMAGE TO STAND, AND/OR FAILURE
RESULTING IN PROPERTY DAMAGE,
PERSONAL OR FATAL INJURY.
Meets or exceeds ASME PALD-1997
standards for performance & safety.

CSE-4000TS 2Rev. 6/18/03
OWNER/USER RESPONSIBILITY
The owner and/or user must have a thorough
understanding of the manufacturer’s operating
instructions and warnings before using this underhoist
stand. Personnel involved in the use and operation of
equipment shall be careful, competent, trained, and
qualified in the safe operation of the equipment and its
proper use when servicing motor vehicles and their
components. Warning information should be emphasized
and understood. If the operator is not fluent in English,
the manufacturer’s instructions and warnings shall be
read to and discussed with the operator in the operator’s
native language by the purchaser/owner, making sure
that the operator comprehends its contents.
Owner and/or user must study and maintain for future
reference the manufacturer’s instructions. Owner and/or
user is responsible for keeping all warning labels and
instruction manuals legible and intact. Replacement
labels and literature are available from the manufacturer.
INSPECTION
Visual inspection should be made before each use of the
underhoist stand, checking for damaged, loose or
missing parts. Each stand must be inspected by a
manufacturer’s repair facility immediately, if accidentally
subjected to an abnormal load or shock. Any stand which
appears to be damaged in any way, found to be badly
worn, or operates abnormally MUST BE REMOVED
FROM SERVICE until necessary repairs are made by a
manufacturer’s authorized repair facility. It is
recommended that an annual inspection of the stand be
made by a manufacturer’s authorized repair facility and
that any defective parts, decals or warning labels be
replaced with manufacturer’s specified parts. A list of
authorized repair facilities is available from
the manufacturer.
ASSEMBLY INSTRUCTIONS
1. Attach legs (#4) to guide weldment (#3) using (3) M10
hex bolts (#13), (3) washers (#14) and (3) M10 hex nuts
(#15). Note: Do not tighten securely until the small
and large braces have been attached.
2. Attach small braces (#5) to legs (#4) using (6) M8 HHCS
(#8) and (6) M8 hex nut (#9). Note: Do not tighten
securely until large braces have been attached.
3. Attach large braces (#6) to legs (#4) using (6) M8 HHCS
(#8) and (6) M8 hex nut (#9). Note: Now securely tighten
all nuts and bolts.
4. Place bearing assembly (#2) on guide weldment (#3) and
screw handle (#10) on worm shaft (#16). Then, place
handle grips (#11) onto ends of handle (#10).
5. Insert the 6mm roll pin (#7) into the hole located near
the bottom of the worm shaft (#16).
6. Set saddle (#1) on top of worm shaft (#16) and screw
M8 hex bolt (#12) through saddle to secure on
worm shaft.
OPERATING INSTRUCTIONS
To Raise:
Turn adjusting handle clockwise until saddle contacts
load. Continue turning handle to raise load to
required height.
To Lower:
Turn adjusting handle counterclockwise.
Capacity . . . . . . . . . . . . . . . . . . . . . .4000 Lbs.
Low Height . . . . . . . . . . . . . . . . . . . . . . . .68"
Raised Height . . . . . . . . . . . . . . . . . . . . . .76"
Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24"
Shipping Weight . . . . . . . . . . . . . . . . .35 Lbs.
CSE-4000TS SPECIFICATIONS

CSE-4000TS 3Rev. 6/18/03
PARTS BREAKDOWN - CSE-4000TS
16
3
4
5
6
7
89
89
13
14
15
12
1
2
11 10 11
ITEM PART
NO. DESCRIPTION NO. QTY.
1Saddle Assembly (incl. 1, 7, 12 & 16) RS6808BD01A 1
2Bearing Assembly RS6808BD02 1
3Guide Weldment 1
4Leg 3
5Small Brace 3
6Large Brace 3
76mm Roll Pin 1
8M8 HHCS 12
9M8 Hex Nut 12
10 Handle (including grips) RS6809A08 1
11 Handle Grip RS6809A03 2
12 Hex Bolt M8 1
13 Hex Bolt M10 3
14 Washer 10 3
15 Hex Nut M10 3
16 Worm Shaft 1
Note: Only items with part numbers are available for purchase.

CSE-4000TS 4Rev. 6/18/03
WARRANTY COVERAGE
Cornwell Quality Tools Company (“Cornwell”) warrants against defects in material and workmanship on this product for a
period of TWO (2) YEARS from the date of original retail purchase. Subject to the conditions and limitations set forth below,
Cornwell will, at its option, either repair or replace any part of the product(s) that proves defective by reason of improper
workmanship or materials.
This warranty does not cover any damage to this product that results from accident, abuse, misuse, natural or personal disaster,
or any unauthorized disassembly, repair, or modification. Repairs, disassembly and modification are only authorized to be made
by Cornwell or a warranty service center approved by Cornwell.
WARRANTY SERVICE
To obtain warranty service, contact your Cornwell dealer.
EXCLUSIONS AND LIMITATIONS
THIS WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES
AND CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. CORNWELL SPECIFICALLY DISCLAIMS ANY AND ALL
IMPLIED WARRANTIES, INCLUDING, TO THE EXTENT PERMITTED BY APPLICABLE LAW, ANY WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IF CORNWELL CANNOT LAWFULLY DISCLAIM IMPLIED
WARRANTIES UNDER THIS LIMITED WARRANTY, ALL SUCH IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE
DURATION OF THIS WARRANTY.
IN NO EVENT SHALL CORNWELL BE LIABLE TO THE PURCHASER OR TO THE USER OF A CORNWELL PRODUCT FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE,
TORT, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, WITHOUT LIMITATION, EXPENSES, LOST REVENUES, LOST
SAVINGS, LOST PROFITS, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE PURCHASE, USE OR
INABILITY TO USE THE CORNWELL PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages or exclusions or limitation on the
duration of implied warranties or conditions, so the above limitations or exclusions may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights that vary by state.
Repair kits and replacement parts are available for many Cornwell products, regardless of whether or not the product is still
covered by a warranty plan.
Cornwell Quality Tools Company
667 Seville Road • Wadsworth, OH 44281-1094