5Attach the wall plate to the wall using the drywall screws from the hardware kit (see Fig. 8).
Ensure that the wall plate remains level.
A
B
NOTE: This mount comes with a variety of screw lengths and diameters to accommodate
different display models. Not all of the hardware in the kit will be used. If you cannot find the
appropriate screw size in the kit provided, consult with the manufacturer of your display or a
professional installer.
Part 2 – Attaching the Mount to the Display
IMPORTANT! Use extra care during this part of the installation to avoid damaging your display.
4Insert a concrete anchor from the hardware kit into each hole so that it is flush with the
concrete surface (see Fig. 7). A hammer can be used to lightly tap the anchors into place if
necessary.
1
1
To adjust the tilt angle or rotate your screen, firmly grasp the sides of your display and
carefully move it into position. If you find the mount is too difficult to move or is too loose
to hold your display in position, adjust the three screws located directly behind the head of
the mount using the S4 Allen key (H) from the hardware kit
(see Fig. 12)
. Adjust all three
screws evenly.
2
3
Swivel adjustments can be made simply by moving your display to the desired position. If
any of the swivel joints are too tight or too loose, they can be adjusted using the S4 Allen
key (H) from the hardware kit
(see Fig. 13)
.
Periodically clean your mount with a soft, dry cloth. Inspect all screws and hardware at
regular intervals to ensure that no connections have become loose over time. Re-tighten
as needed.
WARRANTY PERIOD: 1 YEAR.
Ready•Set•Mount is a registered trademark of Creative Concepts International, LLC. Supplier Warranty: Creative Concepts
International, LLC will replace this product if, due to defective parts or workmanship, it does not perform as specified by Creative Concepts International,
LLC. This limited warranty extends to the original purchaser for 1 year from the date of purchase. Creative Concepts International, LLC shall warrant any
replacement product for the remainder of the Warranty Period of the product which it replaces. In no event does this warranty extend to instances where
the product is opened or damaged through abnormal use, misuse, Installation, mishandling, neglect, accident tampering or detrimental exposure,
including without limitation: (i) abnormal wear and tear or damage caused by use or handling which is contrary to the instructions published by Creative
Concepts International, LLC, (ii) any cause beyond the control of Creative Concepts International, LLC, including without limitation conditions caused by
movement, settlement or structural defects of the environment in which the product is installed , fire, wind, hail, flood, lightning or other acts of God, any
conditions related to, or caused by, intentional acts, accidents, negligence or foreign matter or energy, or (iii) any damage to the finish of a product after it
leaves Creative Concepts International, LLC, manufacturing facility. EXCEPT FOR THE FOREGOING, THE PRODUCT IS PROVIDED AS IS AND CREATIVE
CONCEPTS INTERNATIONAL, LLC MAKES NO REPRESENTATION OR WARRANTY (WHETHER STATUTORY, EXPRESS OR IMPLIED), INCLUDING WITHOUT
LIMITATION ANY REPRESENTATION OR WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT, WITH RESPECT
TO THE PRODUCT OR OTHERWISE. TO THE EXTENT AN IMPLIED WARRANTY CANNOT BE EXCLUDED, SUCH WARRANTY IS LIMITED IN DURATION TO THE
WARRANTY PERIOD. THIS DISCLAIMER AND EXCLUSION SHALL APPLY EVEN IF THE EXPRESS WARRANTY SET FORTH ABOVE FAILS OF ITS ESSENTIAL
PURPOSE. In no event will Creative Concepts International, LLC be liable for (i) incidental, special or consequential damages arising out of the use or
inability to use the product, or (ii) any OTHER damages in excess of the purchase price arising out of the use or inability to use the product.
OPERATION AND ADJUSTMENT
2
Determine the correct length of screw to use by again examining the back of your display:
If the back of your display is flat and the mounting holes are flush with the surface, use
the shorter screws from the hardware kit.
If the back of your display is curved or if additional space is needed between the display
and the mount, use the longer screws from the hardware kit.
3
Determine the correct diameter of screw to use by carefully trying one of each size from the
hardware kit. Do not force any of the screws – if you feel resistance stop immediately
and try a smaller diameter screw.
Attach the mount to the back of your display using the screws identified in steps 1 and 2 (see
Fig. 9). If you are using the longer screws, you may also need to use spacers (G).
Fig. 9
Fig. 10
Fig. 12
Fig. 13
Fig. 11
Part 3 – Final Assembly
1
2
To complete the installation, carefully slide the mount with your display attached into the
wall plate until the plastic piece at the top of the wall plate clicks
(see Fig. 10)
.
Do not release
the display until the display plate is securely placed in the wall plate.
If you need to remove the display from the wall, push the plastic piece at the top of the
wall plate in and carefully slide the mount upwards and out of the wall plate.
3
Tighten the set screw located on the bottom front portion of the wall plate using the S4 Allen
key (H) from the hardware kit
(see Fig. 11)
. Remember to loosen the set screw before
attempting to remove the mount from the wall plate.
4
Cables can be routed through the cable management hook to keep them organized and
out of the way. Make sure no cables can be pinched when operating the mount.
RSMWA10 Rev 20170531
Fig. 7
Fig. 8
IMPORTANT! The set screw should be used at all times to prevent the mount from being
accidentally lifted from the wall plate.
For displays with curved or
recessed backs.
For displays with
at backs.
3000000-170531
