Realfiction Dreamox XL3 Basic Stand User manual

Stand assembly guide
Version 1.0
Dreamoc XL3 Shelf Opon StandDreamox XL3 Basic Stand

2
When receiving the Dreamoc XL3 Stand
1. 2 x Side Panels (Indencal)
2. 2 x Top / Boom Panels (Indencal)
3. 1 x Power extension cord
4. 1 x Carpet
5. 32 x Ø5, 70 mm Screws
6. User Instrucon
7. 1 x 3 mm Unbrako key
8. 4 x Adjustable Feet
9. 8 x Self - adhesive felt pads
10. Black Plasc Strip
11. 4 x Shelf Support (for Dreamoc XL3 Shelf Opon Stand)
1 2 3
5
6
7
9
8
10
4
11
Package contents Dreamoc XL3 Shelf Opon Stand
1. 2 x Back-Wall parts
2. 1 x Shelf
Package contents Dreamoc XL3 Basic Stand

3
How to assemble the Dreamoc XL3 Stand
Note: To avoid damage or scratches we recommend to assemble the stand on top of the carpet that
comes with the product.
1.
When all the parts have been unboxed, place one of the Side Panels on the carpet as shown below
and take out the accessories bag from within the Side Panel.
2.
Assemble the Boom Panel with the Side Panel.
Start by placing the Boom Panel in a 90° angle to the Side Panel and slide them together.

4
Use 8 x screws and the Unbrako key to fasten the 2 parts together.
TIP: If you have a power drill we recommend to use it to speed-up the workow.
3.
Take the Power extension cord and make sure it runs inside the Side Panel.

5
Place it on the carpet, in a 90° angle to the Boom Panel and slide them together.
Ensure that the male plug comes out the boom, and the female plug at the top.
Assemble the 2 Panels with screws as described in Step 2.
4.
Mount the 4 x Adjustable feet.
IF YOU HAVE THE SHELF OPTION, PLEASE SKIP TO STEP 7 NOW.

6
The Basic Stand is now ready, and you can place your Dreamoc XL3 on top and connect the cable.
6.
Turn the Dreamoc XL3 Stand, so its stands on its feet.
Secure the power extension cable to the Stand with the Black Plasc strip, to avoid it from disappear-
ing down inside the Stand.
Aer you have aached it to the stand, you can safely drop the plug into the stand trough the hole.
5.
Assemble the Top Panel with the 2 Side panels.
FOR SHELF OPTION GO TO STEP 7
ONLY BASIC STAND

7
Insert the second Back-Wall part, while making sure the overlaps match, and both parts are aligned.
7.
Install the 2 x Back-Wall parts.
Each Back-Wall part has a at side and an overlap. The overlap must face towards the center.
Place the Back-Wall part as shown, and then slide the pins into the holes.
If you nd it dicult to get the pins into the holes, you can aach the self-adhesive felt pads on the
back side of the Back-Wall part to get the perfect height. Remove them again aer assembly.

8
8.
Assemble the Top Panel with the 2 Side Panels and ghten it with screws.
9.
Mount the 4 Shelf Supports (shelf hangers) in the desired height.
Return the Dreamoc XL3 stand to its feet, and place the shelf securely on top of the Supports.

9
10.
Secure the power extension cable to the Stand with the Black Plasc strip, to avoid it from disappear-
ing down inside the Stand.
Aer you have aached it to the stand, you can safely drop the plug into the stand trough the hole.
Your Stand is now ready, and you can place your Dreamoc XL3 on top and connect the cable.

10
Realcon and Dreamoc are registered trademarks owned by Realcon ApS. Other marks may be menoned here in that be-
long to other companies. © 2016 Realfcion Aps. All rights reserved.
Realcon Aps | Øster Alle 42, 7th oor | DK-2100 Copenhagen Ø Denmark | Phone: [phone]
For further informaon and pricing please contact Realcon
Phone: [phone]
email: contact@realcon.com