Reckhorn A-400 User manual

Wwww.reckhorn.com
subwoofer amplifier user manual
A-400 subwoofer amplifier with complete crossover and room equalization
This professionally designed and produced amplifier will satisfy highest expectations
regarding sound, power, frequency control, room adjustment and variable satellite speaker
signal. The high reliabilty is based on an oversized heatsink aluminium housing and safety
circuits protecting the subwoofer.
A-400
A-400 Subwooferverstärker mit kompletter Frequenz- und Raumanpassung
Dieser professionell konstruierte und gefertigte Verstärker befriedigt höchste Ansprüche an
Klang, Leistung, Frequenzregelung, Raumanpassung und variablem
Satellitenausgangssignal. Das Aluminiumgussgehäuse als überdimensionierter Kühlkörper
und diverse Schutzschaltungen gewährleisten eine hohe Betriebssicherheit und schützen
die Lautsprecher.
R CKHORN
--
+++
-
LR
RL
SPEAKER INPUT
R L
Subwoofer Verstärker Bedienungsanleitung
-1-
(~230V/50Hz/500W/6A/250V)

Technical data:
AC supply 230 V / 50 Hz or 110 V / 60 Hz according to back side printing
internal power supply with 40000 uF storage capacitance
protection circuits against overheat and shortcut with speaker relay / breaker
damping factor at 8 ohms 250
output power at total distortion level 0.02 % 170 watts / 8 ohms
output power at total distortion level 0.02 % 250 watts / 4 ohms
output power at total distortion level 0.02 % 400 watts / 2 ohms
output power at total distortion level 2 % 280 watts / 4 ohms
frequency response subwoofer with subsonic filter at 15 Hz 15 -150 Hz / -1 dB
frequency response satellite output 50 - 40000 Hz -1 dB
signal-noise ratio over 95 dB
RCA low input sensitivity 0.1 volts / 10 ohms
speaker high input sensitivity 1.2 volts
high cut frequency variable 40 - 150 Hz / 24 dB
bass boost variable 0 to +6dB
bass boost frequency variable 20 - 55 Hz
equalizer decrease variable 0 to -6 dB
equalizer decrease frequency variable 22 - 80 Hz
subsonic filter variable 15 - 40 Hz / 24 dB
phase shift variable 0 - 270°
satellite high pass variable 50 - 150 Hz / 24 dB
satellite output signal +3 dB / 47 k ohms
standby automatic off without signal after 30 seconds
standby power consumtion max. 10 watts
max. power consumption 700 watts
width x height x depth / mm 425 x 100 x 240
weight 8 kg
Subwoofer combinations
All passive subwoofers with minimum impedance of 2 ohms can be driven. The A-400 has
exeptionally strong deep bass power and must be adjusted to the power rating of the subwoofer.
Subwoofer connection with these steps
1. POWER at OFF, all knobs far left, HIGH CUT far right
2. LOW INPUT connect as sketches A to G. B is useful if the Subwoofer input
signal is too low. C is requested if SAT OUT = Satellite output signal is needed. At F and
G the level is only adjustable at A-400.
H and J show the connection to a separate amplifier for satellite speakers.
RL R
Audio/Video Receiver
LFE-MONO OUT
LOW INPUT
A-400
Audio/Video Receiver
PRE OUT FRONT
CA
Audio/Video Receiver
LFE-MONO OUT
Stereoamplifier
PRE OUT
LOW INPUT
A-400
L R
L R
Preamplifier
OUTPUT
D E
B
LOW INPUT
A-400
LOW INPUT
A-400
L R
L R
LOW INPUT
A-400
L R
L R
-2-

G
L R
L R
Stereoamplifier
TAPE REC
L R
L R
Taperecorder / CD
OUTPUT
F
LOW INPUT
A-400
LOW INPUT
A-400
J
L R
L R
A-400
SAT OUT
L R
L R
A-400
SAT OUT
H
Stereoamplifier
MAIN IN or AUX
Poweramplifier
INPUT
3. If RCA connection is not possible connect as sketch K.
4. SUBWOOFER OUTPUT connect to subwoofer speaker as sketches L = total impedance
2 - 8 ohms, M = total impedance 2 - 4 ohms, N = total impedance = 4 - 8 ohms. The amplifier
delivers the highest power at 2 ohms. The sound and overload safety are the best at 8 ohms.
A-400 HIGH INPUT
Stereo amplifier speaker output
4 - 8Ù
N
-
+
-
+
-
+
-
+
2 - 8Ù
-
+
-
+
4 - 8Ù
+
-
2 - 4Ù
-
+
-
2 - 4Ù
+
-
+
-
-
++
A-400
SUBWOOFER OUTPUT
RIGHT A-400
SUBWOOFER OUTPUT
A-400
SUBWOOFER OUTPUT
LEFT
K L M
-
+
-
+
5. If the voltage printed at the back side (110 V or 230 V) is equivalent to your house voltage
connect AC INPUT with your house AC with the attached cable. Due to the high switch-on
power at least a 230V/10 amp (110V/20 amp) house fuse is needed.
6. Play your main amplifier at low level music with deep bass
7. POWER at On and LEVEL turn right until you hear sound from your subwoofer
8. At medium loudness adjust all knobs as shown below. The numbers are related to clocklike setting,
examples: 7 = 7 o'clock = far left, 12 = 12 o'clock = upright, 5 = 5 o'clock = far right
9. POWER OFF: amplifier is totally off = no electric power wasted
10. POWER ON: amplifier on = steady electric consumption 10 watts with STANDBY ON
11. PROTECT LED: lights up at faulty operation as too low speaker impedance / short cut,
overload, overheat
12. CLIPPING LED: a short light up indicates that overload starts but it is still tolerable at
very short bass impulses. At stronger light up reduce LEVEL. At speaker shortcut, too low
impedance and overload the relay cuts the speaker and the LED steady on. After about
every 10 seconds the circuit tests if the shortcut, low impedance or overload has been relieved.
13. STANDBY LED: lights at standby mode
14. STANDBY OFF: amplifier is always on with POWER ON
15. STANDBY ON: amplifier switches on immidiately with input signal and switches
automatically back into standby mode after 30 seconds without signal
16. LEVEL SUB: 7=no sound, 5=maximum input sensitivity
17. HIGH CUT: cuts high frequencies above 7=40Hz, 8=55H, 9=65Hz, 10=70Hz, 11= 75Hz,
12=77Hz, 1=80Hz, 2=90Hz, 3=110Hz, 4=125Hz, 5=150Hz
18. BOOST LEVEL: increases the level at 7=0dB, 8=0.5dB; 9=0.8dB, 10=1dB, 11=2dB, 12=2.5 dB, 1=3dB,
2=4dB, 3=4.5dB, 4=5dB, 5=6dB
19. BOOST FREQUENCY: sets the BOOST frequency at 7=20Hz, 8=22Hz, 9=23Hz, 10=25Hz, 11=30Hz,
12=35Hz, 1=35Hz, 2=40Hz, 3=45Hz, 4=50Hz, 5=55Hz
20. EQUALIZER LEVEL: reduces the level at the frequency set by EQUALIZER ,FREQUENCY at 7 = 0dB, 8 =
0.5 dB, 9 = 1 dB, 10 = 1.8 dB, 11 = 2.5 dB, 12 = 2.5 dB, 1= 3,5 dB, 2 = 4 dB, 3 = 4.5 dB, 4 = 5 dB, 5 = 6 dB
21. EQUALIZER FREQUENCY: adjusts the narrow bandwith decrease at 7=22 Hz, 8=30Hz, 9=40Hz,
10=43Hz, 11=50Hz, 12=65Hz, 1=70Hz, 2=72Hz, 3=75Hz, 4=78Hz, 5=80Hz
22. SUBSONIC: filters unwanted lowest frequencies below 7=15Hz, 8=16Hz, 9=18Hz, 10=19Hz, 11=21Hz,
12=24Hz, 1=28Hz, 2=30Hz, 3=33Hz, 4=37Hz, 5=40Hz,
23. PHASE: adjusts the subwoofer for same acoustical phase as the front speaker at the preferred listening
spot. Listening test for best mix of front speaker and subwoofer is essential.
24. SAT OUT: limits the lowest frequency of the satellite speakers at 7=50Hz, 8=55Hz, 9=60Hz, 10=65Hz,
11=70Hz, 12=80Hz, 1=90Hz, 2=100Hz, 3=110Hz, 4=130Hz, 5=150Hz.
-3-

10 20 30 40 6050 70 80 100 200 400300 500
+10
+5
+7.5
+2.5
0
-2.5
-7.5
-5
-10
-12.5
-15
-17.5
-20
BOOST FREQUENCY
7 o’clock
+10
+5
+7.5
+2.5
0
-2.5
-7.5
-5
-10
-12.5
-15
-17.5
-20
10 20 30 40 6050 70 80 100 200 400300 500
+10
+5
+7.5
+2.5
0
-2.5
-7.5
-5
-10
-12.5
-15
-17.5
-20
10 20 30 40 6050 70 80 100 200 400300 500
10 20 30 40 6050 70 80 100 200 400300 500
+10
+5
+7.5
+2.5
0
-2.5
-7.5
-5
-10
-12.5
-15
-17.5
-20
EQUALIZER FREQUENCY
7 o’clock
10 20 30 40 6050 70 80 100 200 400300 50010 20 30 40 6050 70 80 100 200 400300 500
+10
+5
+7.5
+2.5
0
-2.5
-7.5
-5
-10
-12.5
-15
-17.5
-20
SUBSONIC
7 o’clock
+10
+5
+7.5
+2.5
0
-2.5
-7.5
-5
-10
-12.5
-15
-17.5
-20
+10
+5
+7.5
+2.5
0
-2.5
-7.5
-5
-10
-12.5
-15
-17.5
-20
10 20 30 40 6050 70 80 100 200 400300 500 10 20 30 40 6050 70 80 100 200 400300 50010 20 30 40 6050 70 80 100 200 400300 500
12 o’clock 5 o’clock
12 o’clock 5 o’clock
12 o’clock 5 o’clock
+10
+5
+7.5
+2.5
0
-2.5
-7.5
-5
-10
-12.5
-15
-17.5
-20
SAT OUT
7 o’clock
+10
+5
+7.5
+2.5
0
-2.5
-7.5
-5
-10
-12.5
-15
-17.5
-20
+10
+5
+7.5
+2.5
0
-2.5
-7.5
-5
-10
-12.5
-15
-17.5
-20
10 20 30 40 6050 70 80 100 200 400300 500 2K 10K 20K 10 20 30 40 6050 70 80 100 200 400300 500 2K 10K 20K 10 20 30 40 6050 70 80 100 200 400300 500 2K 10K 40K 50K40K 50K40K 50K
12 o’clock 5 o’clock
-4-
dB
dB dB
dB
10 20 30 40 6050 70 80 100 200 400300 500
+10
+5
+7.5
+2.5
0
-2.5
-7.5
-5
-10
-12.5
-15
-17.5
-20
HIGH CUT
7 o’clock
+10
+5
+7.5
+2.5
0
-2.5
-7.5
-5
-10
-12.5
-15
-17.5
-20
10 20 30 40 6050 70 80 100 200 400300 500
+10
+5
+7.5
+2.5
0
-2.5
-7.5
-5
-10
-12.5
-15
-17.5
-20
10 20 30 40 6050 70 80 100 200 400300 500
5 o’clock
12 o’clock
dB
+10
+5
+7.5
+2.5
0
-2.5
-7.5
-5
-10
-12.5
-15
-17.5
-20
+10
+5
+7.5
+2.5
0
-2.5
-7.5
-5
-10
-12.5
-15
-17.5
-20
The following graphs show frequency
curves at these knob settings: 7 o’clock 12 o’clock 5 o’clock

Technische Daten
Stromversorgung 230 V / 60 Hz oder 110 V / 50 Hz gemäß Aufdruck auf der Geräterückseite
Netzteil mit 40.000 uF Speicherkapazität
Schutzschaltungen gegen Überhitzung und Kurzschluss durch Lautsprecherrelais
Dämpfungsfaktor an 8 Ohm 250
Ausgangsleistung bei Gesamtverzerrung 0,002 % 170 Watt / 8 Ohm
Ausgangsleistung bei Gesamtverzerrung 0,002 % 250 Watt / 4 Ohm
Ausgangsleistung bei Gesamtverzerrung 0,002 % 400 Watt / 2 Ohm
Ausgangsleistung bei Gesamtverzerrung 2 % 280 Watt / 4 Ohm
Frequenzgang Subwoofer mit Subsonic Filter 15 Hz 15 - 150 Hz / -1dB
Frequenzgang Satellitenausgang 50 - 40000 Hz / -1dB
Störabstand über 95 dB
Eingangsempfindlichkeit Cinch 0,1 Volt / 10 k Ohm
Eingangsempfindlichkeit bei Lautsprecheransteuerung 1,2 Volt
Tiefpass 40 - 150 Hz / 24 dB
Bassanhebung variabel 0 bis +6 dB
Bassanhebung Einsatzfrequenz variabel 20 - 55 Hz
Equalizer Absenkung variabel 0 bis -6 dB
Equalizer Einsatzfrequenz variabel 22 - 80 Hz
Subsonic Filter variabel 15 - 40 Hz / 24 dB
Phasendrehung variabel 0 - 270°
Satelliten Hochpass variabel 50 - 150 Hz / 24 dB
Ausgangssignal Satelliten +3 dB / 47 k Ohm
Standby Abschaltung ohne Signal nach 30 Sekunden
Standby Stromverbrauch max. 10 Watt
Maximale Leistungsaufname 700 Watt
Breite x Höhe x Tiefe / mm 425 x 100 x 240
Gewicht 8 kg
Geeignete Subwoofer
Betrieben werden können alle passiven Subwoofer ohne eigenen Verstärker bis zu einer Mindestimpedanz von 2 Ohm.
Der A-400 ist besonders tiefbassstark und muss gemäss der Belastbarkeit des Subwoofers eingestellt werden.
Inbetriebnahme in folgenden Schritten
1. POWER auf OFF, alle Regler ganz links, HIGH CUT ganz rechts
2. LOW INPUT verbinden nach den Skizzen A bis G. B ist sinnvoll, wenn das Subwoofer Eingangssignal zu schwach ist.
C ist erforderlich, wenn SAT OUT = Satellitenausgangssignal benötigt wird. Bei F und G ist eine Lautstärkeregelung
nur am A-400 möglich. H und J zeigen die mögliche Verbindung zu einem getrenntem Verstärker für Satellitenlautsprecher.
RL R
Audio/Video Receiver
Subwoofer Ausgang
LFE-MONO OUT
LOW INPUT
A-400
Audio/Video Receiver
Cinchausgang FRONT
PRE OUT FRONT
C
G
A
Audio/Video Receiver
Subwoofer Ausgang
LFE-MONO OUT
Stereoverstärker
Vorverstärkerausgang
PRE OUT
LOW INPUT
A-400
L R
L R
Vorverstärker
Ausgang
OUTPUT
L R
L R
Stereoverstärker
Tonbandaufnahme
TAPE REC
L R
L R
Tonband / CD
Ausgang
OUTPUT
D E
F
LOW INPUT
A-400
LOW INPUT
A-400
B
LOW INPUT
A-400
J
L R
L R
A-400
SAT OUT
L R
L R
A-400
SAT OUT
H
Vollverstärker
oder MAIN IN
Endverstärker Eingang
LOW INPUT
A-400
L R
L R
LOW INPUT
A-400
L R
L R
-5-

5. Wenn die auf der Rückseite aufgedruckte Netzspannung (110V oder 230V) gleich ist Ihrer Hausnetzspannung,
verbinden Sie AC INPUT mit Ihrer Haussteckdose mit dem beiliegenden Netzkabel. Aufgrund des hohen
Einschaltstromes benötigen Sie mindestens eine 230V/10 Ampére (110V/20 Ampére) Haussicherung.
6. Betreiben Sie Ihren Hauptverstärker mit Musik mit Tiefbass in geringer Lautstärke.
7. POWER auf ON und LEVEL nach rechts drehen bis Sie etwas aus dem Subwoofer hören.
8. Bei mittlerer Lautstärke stellen Sie jetzt alle Regler ein wie unten genannt. Die Zahlen beziehen sich auf die
Uhrzeigerstellung, Beispiele: 7 = 7 Uhr = ganz links, 12 = 12 Uhr = oben, 5 = 5 Uhr = ganz rechts am Ende.
Die Schaubilder auf Seite 4 zeigen Frequenzgänge bei 7, 12 und 5 Uhr.
9. POWER OFF: Verstärker abgeschaltet = kein Stromverbrauch.
10. POWER ON: Verstärker eingeschaltet = Dauerstromverbrauch 10 Watt mit STANDBY ON.
11. PROTECT Lampe: leuchtet bei Störungen wie zu niedriger Lautsprecherimpedanz und -kurzschluss, Überlastung,
Überhitzung.
12. CLIPPING Lampe:
13. STANDBY Lampe: zeigt Bereitschaftsschaltung.
14. STANDBY OFF: Verstärker ist mit POWER ON immer eingeschaltet.
15. STANDBY ON: Verstärker schaltet sofort ein mit Eingangssignal und nach 30 Sekunden ohne Signal zurück auf
Bereitschaftsschaltung.
16. LEVEL SUB: 7 = keine Lautstärke, 5 = maximale Eingangsempfindlichkeit / Lautstärke.
17. HIGH CUT: filtert höhere Frequenzen über 7=40Hz, 8=55Hz, 9=65Hz, 10=70Hz, 11=75Hz, 12=77Hz, 1=80Hz,
2=90Hz, 3=110Hz, 4=125Hz, 5=150Hz.
18. BOOST LEVEL: erhöht den Pegel bei 7=0dB, 8=0,5dB, 9=0,8dB, 10=1dB,11=2dB, 12=2,5dB, 1=3dB, 2=4dB,
3=4,5dB, 4=5dB, 5=6dB.
19. BOOST FREQUENCY: regelt den BOOST Einsatzpunkt bei 7=20Hz, 8=22Hz, 9=23Hz,
10=25Hz, 11=30Hz, 12=33Hz, 1=35Hz, 2=40Hz, 3=45Hz, 4=50Hz, 5=55Hz.
20. EQUALIZER LEVEL: reduziert den Pegel bei der durch EQUALIZER FREQUENCY eingestellten Frequenz um 7 =
0 dB, 8 = 0,5 dB, 9 = 1 dB, 10 = 1,8 dB, 11 = 2,5 dB, 12 = 3 dB, 1 = 3,5 dB, 2 = 4 dB, 3 = 4,5 dB, 4 = 5 dB, 5 = 6 dB.
21. EQUALIZER FREQUENCY: regelt die Frequenz, um die herum schmalbandig abgesenkt wird bei 7=22Hz, 8=30Hz,
9=40Hz, 10=43Hz, 11=50Hz, 12=65Hz, 1=70Hz, 2=72Hz, 3=75Hz, 4=78Hz, 5=80Hz.
22. SUBSONIC: unterdrückt unerwünschte tiefste Frequenzen unter 7=15Hz, 8=16Hz, 9=18Hz, 10=19Hz, 11=21Hz,
12=24Hz, 1=28Hz, 2=30Hz, 3=33Hz, 4=37Hz, 5=40Hz.
23. PHASE: regelt den Subwoofer auf gleiche akustische Phase wie die Hauptlautsprecher. Bezogen auf den Hörplatz
stellt man durch Probieren das beste Zusammenspiel mit den Hauptlautsprechern ein.
24. SAT OUT: begrenzt Übergangsfrequenz der Satellitenlautsprecher auf 7=50Hz, 8=55Hz, 9=60Hz, 10=65Hz,
11=70Hz, 12=80Hz, 1=90Hz, 2=100Hz, 3=110Hz, 4=130Hz, 5=150Hz.
ein kurzes Aufblinken deutet auf anfängliche Übersteuerung, ist jedoch bei sehr kurzen
Bassimpulsen noch unbedenklich. Bei stärkerem Aufblinken muss LEVEL zurückgedreht werden. Bei Lautsprecher-
kurzschluss und starker Überlastung schaltet das Schutzrelais ab und die Lampe bleibt an. Nach ca. 10 Sekunden
prüft die Schaltung, ob der Kurzschluss, die zu niedrige Lautsprecherimpedanz oder die Überlastung behoben
wurde.
3. Wenn keine Cinchverbindung möglich ist, verbinden Sie nach Skizze K.
4. SUBWOOFER OUTPUT verbinden Sie mit Ihrem SUBWOOFER nach Skizzen: L = Gesamtimpedanz 2 - 8 Ohm,
M = Gesamtimpedanz 2 - 4 Ohm, N = Gesamtimpedanz 4 - 8 Ohm. Die Leistungsabgabe ist bei 2 Ohm am höchsten,
der Klang und die Überlastsicherheit sind bei 8 Ohm am besten.
A-400 HIGH INPUT
Stereoverstärker Lautsprecherausgang
Stereo amplifier speaker output
4 - 8Ù
N
-
+
-
+
-
+
-
+
2 - 8Ù
-
+
-
+
4 - 8Ù
+
-
2 - 4Ù
-
+
-
2 - 4Ù
+
-
+
-
-
++
A-400
SUBWOOFER OUTPUT
Rechts-RIGHT A-400
SUBWOOFER OUTPUT
A-400
SUBWOOFER OUTPUT
Links-LEFT
K L M
-
+
-
+
-6-
Table of contents
Languages:
Other Reckhorn Amplifier manuals