RecorderGear SC600W User manual

SC600W
WIFI IP HIDDEN CAMERA
USER MANUAL

In order to comply with 18 U.S. Code § 2512 federal
law (USA), the audio recording function has been
removed from this device. Please be familiar with your
country and state surveillance laws before using this
product. RecorderGear will not be held liable for any
illegal use of this product.
This Device is Compliant with
USA Surveillance Laws
1 YEAR WARRANTY
All RecorderGear™ brand products are backed
by our 1 Year Warranty. For full details visit
WWW.RECORDERGEAR.COM
MID: AI-IP80
MADE IN CHINA

MULTIPLE HIDDEN CAMERAS.
MULTIPLE LOCATIONS.
ONE APP.

4

5
Table Of Contents
Section & Title Page #
1Charging 6
2Insert/Eject Micro SD Card 7
3Power On/Off 8
4Record In Continuous/Motion Detection 8
5Access Saved Recordings 10
6Download The RecorderGear APP 11
7Set-up Wi-Fi IP Camera Function 11
8Understanding The RecorderGear APP 17
9Live Stream Screen Settings 21
10 Device Settings Menu 25
11 Device Settings 26
12 Troubleshooting 30
13 Clock Set-up/Function 31
14 FM Radio 33
15 Specs 34

6
1Charging
The SC600W operates o wall power or
batteries. If using batteries, we recommend
fully charging the SC600W before your
rst use. It takes approximately 7.5 hrs to
charge.
1. Charging The SC600W
A. Open the back of the SC600W by sliding
the cover. Remove the paper tab in between
the battery.
B. Using the included mini USB cable, plug
the SC600W into a computer USB port or a
USB wall adapter.
C. The charging indicator light on the back of
the SC600W will light up red to indicate it is
charging (the light is under the back cover).
NOTE: To operate the SC600W using wall
power (instead of batteries), just plug it in as
if you were charging it.

7
2Insert/Eject Micro SD
Card
The SC600W supports up to a 128GB micro
SD card. The purpose of the SD card is to
store the bulk of your surveillance footage.
Without an SD card, you can still live
stream video, get motion activated alerts,
& record video clips to your iOS/Android
device using the App (see section 6).
1. Insert A Micro SD Card
A. Open the back of the SC600W by sliding
the cover. Insert a micro SD card into the
card slot. We recommend a class 10 card.
B. You will feel a click when the micro SD
card has been inserted correctly.
2. Remove The Micro SD card
A. Push the card in until you feel a spring
release & the card will eject when you let go.

8
3Power On/O
A. Power On - Make sure a micro SD card is
inserted & slide the power switch to the ON
position (located under the back cover).
B. Power O - Slide the power switch to OFF
4Record In Continuous/
Motion Detection
The SC600W can record in either
continuous or motion activation. The
default mode is continuous; it will
automatically start recording in this mode
when it is initially powered on. If you set
it to motion activation, it will run in this
mode the next time you power it on.
1. Continuous Recording
A. Make sure a micro SD card is inserted &
slide the power switch to the ON position.
B. The front indicator light will show blue for
5 seconds & then turn OFF. After 15 seconds,
the light will turn back on for 20 seconds &
turn back OFF for 10 seconds. After the 10

9
seconds, it will begin flashing.
C. Once the blue light begins flashing
continuously, recording has begun.
NOTE: When the SC600W is connected as a
Wi-Fi IP camera, the front indicator light will
no longer flash, but be a solid blue light. To
turn off the indicator light, see section 9-2D.
2. Motion Detection Recording
Before changing to motion detection
mode, download & connect the camera to
the RecorderGear App (See sections 6-8).
A. After completing sections 6-8 open the
RecorderGear App.
B. Press the Camera Settings icon to the
right of the camera on the Live Video/Main
Page & select Device Settings.
C. Select Recording Settings & tap Record.
D. Select Motion Detection
E. Select OK to save the settings.
F. Select Alarm Settings & change the
Motion Detection Sensitivity to adjust it.
NOTE: Make sure you change the Motion

10
Detection Settings in the Alarm Settings. If
it’s DISABLED, your camera will NOT record in
motion detection. (See section 11-1A)
3. Stop Video Recording
Slide the power switch to the OFF position.
NOTE: The default video file interval length is
3 minutes. To change this, see section 11-3D
5Access Saved
Recordings
There are two methods to access saved
recordings
1. Remove The SD Card
A. Slide the power switch to OFF & remove
the SD card.
B. Insert the SD card into a card reader &
insert it into your PC.
C. Open the disk that appears on your PC.
NOTE: We recommend using VLC media
player to playback your files.
2. Use The RecorderGear App
(See section 8-3)